3d printing crossbow

... It was only off .13mm (.0051 inches) at the most, but not really an issue if you have printed the parts already. Here is very short video of this machine working. https://youtu.be/HgV3grxkY44 I also added optional **CantileverStablizer.stl**.

A constant current driver operating from 6 V to 15 V should do nicely for powering it directly from the main battery and adding an RC switch to control the light by the transmitter.\r\n\r\nI printed the chassis without supports using PETG and lots of...

This model was almost perfect, but when I printed one out, it turned out to be a bit chunkier than I really wanted. So, I figured I'd take my own shot at it and came up with this. My requirements were: * It had to match an authentic full-size...

You'll find the clips as single objects or as a complete set to download and print. Changelog: The clips now hold LM8UU bearings more tightly Bearings are pressed against the Y frame to prevent them from spinning. M3 screw holes are narrower now,...

You may have to warm the rear Pipe Sockets a bit as you put the 8mm Pipe in, but depending on your printer, it'll just fit "Snugly", whereas 7mm Pipe will be a touch loose until you tighten down your bolts/nuts.Seriously, use PLA+ (PLUS) filament...

I made some different designs and prints to hold the start of the wire in the chuck. My thoughts were good, but using them didn't bring the solution. Then I came up with the idea of making a kind of vice that could be placed into the chuck and clamp...

Print instructionsPrinted with PLA plastic at 200 micron and around 7% fill. Mount the two front arms to the main body with a single zip tie. These zip ties should be quite snug, I used pliers. For the rear arm/pivot, first give the hinge slots a...

---------- PRECAUTION: Après quelques prints, il faudra contrôler que les tensions soit toujours bonnes. Procéder à un ajustement ci nécessaire. ---------- Ce custom est un projet personnel, qui m'a pris beaucoup de temps à concevoir et à...

Mount the printed heatblock with the front and back parts of the mold, fix the whole with 2 screws. Make sure it's tight enough. (pictures 7 and 8) 2. Put the freshly assembled block over the bottom part of the mold (picture 9). Make sure the holes...

In a pinch (if your printer has issues printing these tiny bastards), you might be able to get away with some clipped up bits of the unused horns included with your servos. I designed the junction of two shoulder pieces to be held by two 3mm x 6mm...

It was not intended for printing purposes. I wanted to design some custom cases for CHIP and I always start by modeling the subject before moving on to designing accessories. However, until I had the actual CHIP board in my hands, I couldn't even...

There is a new version of this carriage at https://www.thingiverse.com/thing:3615464 AND an even newer one at https://www.thingiverse.com/thing:3688067 ** ** I'd recommend that newest version instead for better rigidity and simpler printing and...

This is mainly composed by Nitrogen (98%) it is 1.45 times the pressure of that of Earth at the surface, and it is 1.19 times more massive. Titan atmosphere has a climate system, in which methane sublimate and form clouds. It is known that Titan has...

You can find more information on the design, characteristics, and group discussion in this forum thread: http://www.rccrawler.com/forum/superclass-crawlers/594046-crazy-axles-idea-design.html Some parts can be printed or CNC cut on Glass Fiber,...

Shoulders and Forearms(https://www.aguilarworkshop.com/product-page/odst-battle-armor-arms)Armored Plate Carrier(https://www.aguilarworkshop.com/product-page/odst-battle-armor-armored-plate-carrier)Utility...

Both had minor errors that possibly causes them to print badlyUpdate 20.11.2023:-32 and 35 is the same, but the file for 32 is flawed and therefore gets deleted.If you like my work please consider supporting me on Patreon.Become a Patron!Some of my...

Planet's rings are stable thanks to the gravitational influence of the planet, and the presence of shepherd moons, like Prometheus and Pandora, that prevents the accretion of the disk material into a denser moon. Saturn is also known for having...

 There are two versions of this stop: a simple one that indexes directly against the material, and one with a hole for a dowel that you can epoxy into place to create a spacer for cuts narrower than the width of the track.You'll want to print two...

Case for Atari 1050 / XF551 floppy power supply unit. Krabička pro napájecí zdroj disketové jednotky Atari 1050 / XF551. Print instructionsenglish text bellow ==== CZ ============ Napájecí zdroj pro floppy Atari 1050 / XF551 Jde o návrh napájecího...

The two `o_ring` files are optional o-rings you could print with flex filament. Better to use o-rings, and at a pinch you can probably get away with using a rubber band, or just pushing everything together and putting up with water splashing...

So, measure twice and print once. In my case, I cured this by simply enlarging the holes with a needle file. But when I came to do this design, I had no idea where the original holes would have been.\r\n\r\nThe rear of the case has positions for two...

Installation ------------ Print out the four switch holders and slide them into the aluminium channel on the X and Y axis, as shown in the photos. The X axis holders are slightly longer than the Y axis holders. The tolerance is quite tight so they...

I encourage experimentation with springs and perhaps with print settings if you know what you're doing to create a blaster fine-tuned to your needs. Grab your Snakethanhas here: https://www.thingiverse.com/thing:3890229 Feedback is very much...

Printed Parts Assembly Mount pt 1 Assembly Mount pt 2 Backer Plate Bearing Filler 3to5mm X 2 Spur Gear11 Spur Gear21 Switch Plate Hardware Bearing: 5mm ID, 10mm OD, 4mm thick X 2 2.5mm x 14mm Cap Screw X 10 2.5mm x 35mm Cap Screw X 7 2.5mm Nuts X 8...

Welcome to the home for the things to print for the Eff-Uno Racer project (https://github.com/oracle-devrel/eff-uno-racer). Eff-Uno Racer is a LEGO© Open Wheel Race Car that you can build and remotely control. Most of it is made with LEGO© bricks...

I provide an easy-to-print alignment tool to ensure the heatsink is perfectly positioned for the cover to fit.\n* Direct airflow through the heatsink, don't leave proper airflow to chance.\n* Duct air in one side and out the opposite to maximize the...

6 is a hinged version, you need to print 3 of the hinges and 2 of the shafts.If you like my work please consider supporting me on Patreon.Become a Patron!Some of my other designs:https://www.thingiverse.com/thing:4654378 - Rivet Cutting...

You can automate it by printing this gearbox that will snap into the mechnisim.I have been successful at driving it with plastic 9g servos after modifying it to be 360. I highly recommand using metal gears which I plan on doing as I already had lost...

# Warning **PLEASE PRINT OFF THE SHROUD AND MOCKUP 4010 BLOWER AND CONFIRM FITMENT BEFORE PURCHASING OR MODIFYING ANYTHING! PLEASE POST IN THE COMMENTS IF THIS SHROUD WORKS FOR YOU AND WHAT CARD YOU HAVE INSTALLED** The shroud is designed to sit...

... done, carefully install your Pi in the bracket, being careful with the pins and make sure all 5 pins go smoothly into the Einsy board. Click the Pi in place so the four printed posts in the corners are flush withe Pi's PCB. ...Snap the cover on.