3d printing cad

- PrusaSlicer recently implemented a change for "Elephant Foot Compensation" that changes how the first layer is printed so that it isn't wider than subsequent layers. - I recommend setting the value for this at .1mm, because I found this change to...

All parts were printed with a 0.2mm Layer height. 3 perimeters, and 20% infill. I used PETG, however other materials would also work. A hardware list is provided. You may also need some basic tools, knifes, small drill bits, etc. Most parts...

I switched materials and I am now convinced that the print quality is actually quite a bit better over the original gantry. Update 2020-04-04: Made a v4. Changes from v3: * Added cable management rings to all the mounts * Added BLTouch versions of...

I Haven't printed it but I'm confident that it'll fit fine. Update 28/07/17: A gallery with larger photos: https://imgur.com/gallery/p00SB Original text: While I don't have a personal interest in modifying the grip for other versions of the...

Use 5050 LED's!  BOM:12v LED...

Results Since I don't print ABS I don’t need to heat the bed up to 100C. I tested it up to 80 about 10 cycles and it now heats a lot faster even without any heat insulation underneath. I checked it with a pyrometer. This is obviously due to better...

I'm creating a modular table game that doesn't require dice - you simply print the pieces and cards. The game involves building a spaceship from its most basic beginning to an interspace station with many inhabitants and resources to manage. It's...

http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following settings: nut_step_angle_radians = 0.7854, thicken_value = 2, hex_head_style = hex, bolt_size_in_mm = 5, screw_length_mm = 25,...

If you print out the following STL files and assemble them, you'll have a complete stand for RPi 2: Stnd-Unt_atd012.123dx -su012-arm-L.stl -su012-arm-R.stl -su012-leg-L.stl -su012-leg-R.stl -su012-dmybtry.stl -su012-stndbs.stl Here are the...

Blocks with other angles can easily be modeled and printed if needed. It should be noted that the complementary angle to the one shown on the gauge can be mitered by placing the material against the other face of the miter gauge. The shooting...

Print nose with supports everywhere and 20% support density. Also use 20% support density with support brim, support roof, and support towers enabled on the LID. Use four walls and 20% infill or more on the nose, and 40% on the LID. The lid also...

I also made the spacer shaft shape wider so it is not as hard to print, nor as fragile to handle. I also eliminated a few of the sizes that I felt were not necessary. --- This is a PPC (Pixel Pipe Clip) spacer tool that will help you accurately...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

... of running pipes to them for water transport and waste management. The angled door arches and angles underneath overhangs should allow this to be printed without supports. Added Version 2. Slices better in Slic3r. ...(tested in 1.0.1 and 1.1.3)

The design consists of 3 parts : 1) the base (about 4 hours) - 12% density zig zag support and 10% gyroid infill 2) the spindle (about 4 hours) 3) the screw (about 20 minutes) Note : spindle has been printed with different support angle. The outer...

Recommended Material for printing: Sainsmart TPU @ 01.mm / 210°C/ 40mm/s / no retraction Update: You can now buy my Gatehunter pod combined with the LeDrone Club Pickle frame from...

Models include the popular cable chains by johnnniewhiskey over on Thingiverse, a PSU mount for the Ender 3 Pro by Cancerix on Thingiverse, amazing riser feet by thrutheframe over on Thingiverse and also some inspiration by zoly15 here on...

If you print and install these and your lathe breaks, congrats; you used a part that some dummy on the internet with a set of calipers and too much time (namely, me), uploaded. If you try this idea, you are doing so at your own risk. I also make no...

This was printed on a Flashforge Guider II, High Quality, so the tolerances are good, but I also allowed a 1/4mm tolerance between parts and at this level of quality, it gave me a good fit. Painting it was using acrylic spray, primed and filled,...

I wanted it to be a very secure fit, strong, lightweight, low-profile, inexpensive, easy to print, and to also not damage the surface of the fork. I managed to achieve those goals.&nbsp;</p><p>I got the idea for this project from k-Lite's design,...

Most parts need to be printed flat/horizontally before being glued together for maximum strength. The only exceptions are the Tops and Bottoms of major Leg and Thigh pieces where stepper motors should slide in. Gluing these together will prevent...

This model is approximately what we saw it can be printed in two halves and glued together. We both agree this is extremely close to what it looked like. Klamath Falls is home to Kingsley Field, the 173rd fighter wing, a F15 and soon a F22 base which...

*Printed and checked. Passes XYZ Calibration and Selftest.* **Credits:** --------------- 1) Inspired by the MGN12 Linear Rails designed by Stwebster (https://www.thingiverse.com/thing:3400952) 2) Y-Tensioner and Z-Motor_Mounts are modified...

As of now, I am awaiting a new Creality hotend as well as the heated bed, and 165mm glass surface before printing can commence. However, movement systems work well. HARDWARE REQUIREMENTS Electronics: NEMA 17 Motor - replacement z-axis motor ...

https://youtu.be/3VeTzbk-lLA Parts other than prints ======================= * ATOM Lite (1 pce.) * universal PCB * pin header * MG90S servo (3 pcs.) * magnetic drawing board 106x76mm (1 pce.) (I used :...

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: Short term tool storage for tools being used on an active project Organization to help keep the bench cleaner To help facilitate rapid tool acquisition...

- Bottom diameter: select a diameter that your printer can bridge when printing the bottom pad. - Bottom thickness: determine how thick the bottom of your planter should be. That's not all - there are also complicated parameters to consider. The...

Therefore, when you choose a spring, its inner diameter should be approximately the same as the outer diameter of the tube.How to usehttps://youtu.be/2PpO4AbOWggThis welder is designed to join the last filament of a roll to a new roll.When using this...

Notable changesGeometry added to mate with the Bear Upgrade V-Slot ExtrusionsUse either drop-in or standard T-NutsUse either M5-10 socket head or M5-8 flat head screwsTemporary M3-12 screw added to aid in sliding T-Nut alignment.Case is 3mm wider to...

This was a substantial enterprise that involved making the spheres, printing the gores, building sturdy stands, packing, and distributing them across Europe. Mercator was also renowned for his scientific instruments, particularly his astrolabes and...