3d printer with raspberry pi

FAQ: http://www.thingiverse.com/shivinteger/about Generating Attributions log: Thing Title: High Reduction Ratio Planetary Drive Thing URL: http://www.thingiverse.com/thing:30615 Thing Author: mkeveney Thing Licence: Creative Commons - Attribution...

I designed it with the S shaped sides for 2 reasons. Mainly because it requires less travel for the printhead and therefore gives a cleaner and quicker print. The second reason is because it looks a bit funky. I see other people putting holes in the...

I made the calibration adjustments with a free Chrome extension called gcode-sender. The baud rate must be set to 115200. I needed gcode-sender because Creality does not provide a way to change the CR10S Pro V2 steps in their stock firmware like the...

This is a stable, long-running top.The center of gravity is perfectly aligned(0.009mm) and technology has been incorporated to reduce aerodynamic drag.!!Emergency Fix!!Conventional rods are not properly toleranced.I provide a modified...

When assembling the parts can be screwed together with 4x 20mm M2.5 (I got them in Brico www.brico.be) WARNING (important, please read): It is advised that you use the DC connector on the SD DOS board to power the SD DOS solution. It requires a...

This stepper is controlled by an Arduino Nano with an attached IR receiver, allowing any IR remote to be used for control. **BOM:** 1x TSOP4838 38 KHz IR Receiver Module 1x 28YBJ-48 Stepper motor 1x ULN2003 Stepper driver 1x Arduino Nano 1x Sponge...

Customized Version of Thingiverse Project 739573 Created with Customizer, Thingiverse Apps Platform Instructions for Using the Options Using the Following Options to Design and Customize: textextruder: set to extruder1 character spacing: adjusted to...

The one that I'm currently using it's the one with no nut cut-out and it works remarkably well. The knob has a slot at the top to slide in a 6-32 nut too, you can add a drop or two of super glue so it will stay at the bottom permanently, although...

DONE!!!!!\r\nAfter countless hours of CAD modeling, the design is finally completed!\r\n\r\nThe model is now being printed on a Duplicator 7 using Monocure rapid as the printing material.\r\nNo additional support was needed for the legs part when...

With its sleek design and attention to detail, it's the perfect way to show off your love for the sport. Whether you're hanging out at the track or just running errands around town, a MotoGP Keyhanger is sure to turn heads. Keyhangers come in all...

This process begins in the mouth with the breakdown of carbohydrates and proteins, which are then further processed in the stomach before being absorbed into the bloodstream. The liver and kidneys also play key roles in filtering waste products from...

QX13 Mound: After the remaining pieces are assembled and ready to mount, this is placed on top of the 6mm bolts protruding from mounted Can-Cover, and affixed with 6mm Wing Nuts. It has the first section of the stem built right in! Be sure to print 2...

Customized version of http://www.thingiverse.com/thing:813330 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=813330 Instructions Using the following options: Height tolerance for primary shape...

The screwed version is not compatible with "chassis-SL." These models also fit: - Three AAA batteries (check my profile for the DLC) - One PS3 controller 1800mAh 3.7V Li-Ion Battery (be careful and only use it if you know what you're doing!)...

 Sand face down to remove the  paint for nice crisp digits.Usage Hint:To determine the amount of filament left on a spool, most manufacturers will have a tech-specs page with the weight of an empty spool.  Use this or weigh an identical empty spool...

The skull must be printed with supports (which worked pretty well, though it's a complicated model and takes a while to print). The stream and splash parts are scaled to 80% of the size of the "Floating Cup" from which they were derived. ...Scale all...

Customized version of http://www.thingiverse.com/thing:41274 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=41274 Instructions Using the following options: 41_height_of_cylinder_indentations = 10...

... need for a brim or supports on the dowel. Same for the jig plate as uneven cooling is far less likely with the circular shape vs square.Jig Plate - 3 walls (or more)Dowel - 8 (to ensure it's solid)  Category: DIY

Pack contains:- 1 x Shapeshifter Svinfylking (Wereboar)- 1 x Battle Ground 40mm Round Base (style: A) Dimensions (assembled and with base):- Shapeshifter Svinfylking (Wereboar) - Width (X): 49,07mm; Length (Y): 60,21mm; Height (Z): 53,08mm Features:-...

Once you've identified these key components, you can begin experimenting with different sounds and techniques to enhance them. This might involve adding new instruments, altering the tempo or pitch of existing ones, or even manipulating the vocals. A...

... door for easier printing - simply glue it in place or use a small hinge. If you're feeling adventurous, try printing the rear body with the integrated door! ... Parts 6-12 are not essential to the build, as they represent the interior equipment.

EnglishCompete with your friends to see who can create the longest word and use all the dice.RulesTry to make the longest word. Letters can be connected like in a crossword puzzle. Players take turns. The first to reach 100 points wins.</p><ul><li>+1...

The opponent looks at his own frame and answers with one of the following possibilities: air - the house is outside any plane - pawn "0" hit - the house is part of a plane, but no cabin was found - pawn "1" downed - the box contains the cockpit (top)...

I had a toy knife with a similarly shaped blade as a kid so I tried to recreate it from memory. As for printing this, I strongly recommend you print one piece at a time, but there is a full sheet if you're confident you won't get stringing! (I...

EN In order to have better stability with the Révopoint POP scanner (especially on whole character scans) I decided to make this Slider. It is controlled by a CNC Shield V4 and from the PC from Gcode (very easy to use) it can also be automatically...

I printed these to use with fan made expansions to the Horrified board game. Check out the amazing custom monsters at boardgamegeek. https://boardgamegeek.com/forum/2977406/horrified/variants Thanks to the various makers. Many of the models...

It looks like a walking radiator with Pop-Eye arms and a bowling ball head. I wanted a Tundra Wolf that did not actually look like a MWDA Tundra Wolf but would look like something I'd want to see on the tabletop - and keep a vague resemblance to...

As we continue to explore the mysteries of the universe, Russell's work serves as a reminder that true understanding can only be achieved by integrating spiritual principles with mathematical insights. ... Note: The Flesch-Kincaid test shows a score of...

With gray filament, they pass as concrete sleepers. To complete them, corresponding rail profiles code 332 (e.g. LGB) are needed. Included in this post, in addition to the sleepers for the dual gauge track, are the sleepers for 64mm track as...

In particular, Sony in the 1980s enjoyed its heyday in the personal audio field with the development of the Walkman. The dimensions are 16 × 5 × 10 (width × length × height) cm. This file can be downloaded from the link below. All files provided...