3d printer stops printing halfway

I was constrained by the size of the rotary switch and the USB breakout board otherwise it might have gotten a bit smaller. See it in action: https://youtu.be/PTTVuVUZYM8 I have included the OpenSCAD file which is somewhat parametric. Print...

... is welcome! Please also have a look at my designs on https://www.thingiverse.com/rolfmobil/designs and https://cults3d.com/en/users/rolfmobil/creations. under the same username (rolfmobil)... Print Settings Supports: Yes Category: Outdoor & Garden

(hence the name Duo, eh?) Addition parts you will need. 2 - 808 (MATEcam) cameras - either a dissaembled keychain version or the DYI version (here are some links)...

... thing of its own. Update 2: Requested by Darije - Added canopies that don't require threaded inserts. Thread 3mm screws right into the plastic - A reinforced V2 frame that might help if printed instead of the much advised CNC'ed carbon route

BOM: the printed part 1/2 wavelength of solid 6ga copper ground wire (plus a little for trimming) coaxial cable coaxial connector for your cable To assemble the antenna: Cut two lengths of the 6 ga copper wire a little longer then 1/4 wavelengths...

PRINTING INSTRUCTIONS: See below. ASSEMBLY AND OPERATING INSTRUCTUONS: 1. Slide the upper part onto the press die side handle as shown in the photos, as far up as it would go. Mark hole positions, drill and attach the upper part with the press...

... Some part coolers like the "Petsfang" & "Bullseye" seem to crash into the camera housing during autobed leveling. Many thanks to "acwest" for pointing out that problem and his solution! ===================================== Have fun printing!

#Filament Used: Grey PLA: https://www.amazon.com/gp/product/B07T47BH73?ie=UTF8&tag=WisePrints206-20&camp=1789&linkCode=xm2&creativeASIN=B07T47BH73 Transparent Blue PLA...

Instructions 1) Print equal numbers of receivers, and grabbers. 2) Slide a couple onto each end of a strut 3) Slide shorter struts into these for support, or whatever 4) Rejoice! By default, these pieces fit on 5/16" wood dowels. You can easily...

Print a bunch of cleats and bollards, they are always good. If you do make this, please please post a make. I'm very keen to see other people getting some use out of these files! ... <iframe width="560" height="315"...

Important notes: All parts can be printed without support, except the steam. There are two models, one opens to the right and the other to the left. The discs with the numbers are used for the two designs, and to fix the combination you have to look...

I'm considering sending it as an engineering sample to Kräus so that they can actually make this themselves to vastly improve their product. Instructions I printed it on a Makerbot Replicator using ABS, with 35% infill. All parts are in a single STL...

Steps: - Print the file - Slide the PTFE into its location at the desired length - Use a felt tip pen to mark the start of the contact on the tube - Take out the tube and cut it round on the outline as on the attached renderings - Replace the tube -...

[0] Thing Title : Personalized Soda Can Holder v2 [0] Thing URL : http://www.thingiverse.com/thing:6591 [0] Thing Author : JadeKnight [0] Thing Licence : Creative Commons - Attribution - Non-Commercial - Share Alike [1] Thing Title : Spider mount for...

"Silicone" stl is a template for cutting, but you could print it out of PETG or ABS for sizing, testing. See <a href="https://www.thingiverse.com/thing:4866682">yydoctt's thing</a> for the non-Pro purge bucket and scripting ideas. <hr> ...

If you're using a servo, you'll also need to print the rev counter (“rev_counter.stl”) and install an extra magnet and an additional reed sensor. On the other hand, if you opt for a stepper, you'll only require an extra coupler. For convenience's...

I suggest printing the top pieces in something more heat resistant than just PLA, preferably carbon fiber nylon or polycarbonate. ASA should work pretty well too. For the bottom pieces, I used PETG as it allowed for the cards to slide in and out...

Before starting, assemble the cylinder by sealing it (there are holes on the sides) and printing it from transparent material for better visibility. If you give up, you can disassemble the game and try again. Good luck! HINTS: This game aims to...

The maximum dimensions of a TFT screen that you can put inside this monitor are given at the end of this description.You need to download and print all the files from the standard version, except CRT and FRONT-GRAY-FRAME, they are replaced with the...

As the buttons require minimal material, I recommend printing a set of each style to ensure a perfect fit. It is easier to solder all wires to the boards before permanently mounting them in the box. By connecting the common pins on the buttons...

Using TMC2130 drivers ([plus my other modifications](https://www.thingiverse.com/glabifrons/collections/glabifronss-anycubic-kossel-mods)) with this hotend and Klipper firmware, I was able to print 400mm/s with fairly nice results (very minimal...

The tool organizer can be printed in 6 modules on a Lulzbot Mini, with an additional slot added to the right side for extra diagonal cutters. Here's what I have organized from left to right: 1.) A Chip Quik SMD Removal Kit is essential for removing...

Print top.stl, middle.stl, bottom.stl, and 4 pin.stl. Refer to the exploded view and attach pins through precise holes in these parts for robust construction. There are some special steps you need to follow here: 1) You may find it useful to...

The print itself is only a case and a lid, but I thought it may inspire some other creative invention. I apologize for the poor quality of the video and my gross fingers. It was really hard to get the camera to recognize the led screen because of...

:) Instructions Well, print: 1 Base 1 Lid 3 Buttons Put the plastic part inside the rectangle in the lid. Put the TreadGaming PCB hardware in. Insert the buttons in the lid. Squeese the sides (to not let the PCB fall out) and turn the base...

I Haven't printed it but I'm confident that it'll fit fine. Update 28/07/17: A gallery with larger photos: https://imgur.com/gallery/p00SB Original text: Whilst I don't have any personal interest in altering the grip for other versions of the...

In a closed case its unneccessary to use bulky plugs everywhere, so i directly soldered the power-in-usb-jack to a dc-jack; to one of the usb-ports i soldered an USB-cable to be able to re-route the USB-DAC to the tray. printed in black PLA, ~50mm/s...

Input and output voltage are applied via four terminal screws.Parts to be printed  AssemblyEverything necessary for assembly can be seen in the next picture. Here are the currently set parameters   controllerbreite92 mmController...

Plus more being added please see table belowSorry Painted in lettering and not double colour printingTaken from https://www.thingiverse.com/thing:3079639I used a draft setting, nozzle 215c bed 60c.&nbsp;Label ListAster American...

Additionally, we will delve into designing an enclosure using Fusion 360, which will be materialized through printing in transparent-white PETG plastic. This color, in our opinion, not only adds visual appeal to the setup but also allows observing...