3d printer ribbon cable

... the Ender3 Pro's MeanWell power supply. ...Helpful if - like me - you have your Raspberry Pi mounted at the back on the machine. Uses 2.5mm hex-screws to attach. Print Settings Rafts: No Supports: No Resolution: 0.20 Category: 3D Printer Accessories

I put a little tape on each side of the clamp to help grip the cable. I also put a little dielectric grease on end of the ribbon to fend off corrosion which could also cause a hot connection. Print instructionsCategory: 3D Printer Parts Print...

This is a tiny clip to hold the flat ribbon cable from a Raspberry Pi Camera in place. ...Use a 2.5 mm (x 10 mm) screw to mount. Print instructionsPrinter Brand: Prusa Printer: Mini Resolution: 0.2mm Speed Infill: 20% Filament: Prusa PLA Brim: Enabled

This is an upgrade for those wanting to upgrade from Icarus 2.0 to 2.1 and want the new ribbon cable holder but don't want to reprint the whole carriage. To do so, cut off 42.0 mm from the old ribbon cable holder and glue this new part in place using...

I didn't want to stuff the ribbon cables on my Prusa MK3S into the extrusions, so I made this twist-in clip to hold the ribbon cables next to the aluminum extrusions.

The AlfaWise U30 display ribbon cable clip is a vital component that secures the delicate ribbon cables in place, preventing damage and ensuring seamless performance of the device's display screen.

I lost one of my ribbon cable clips, so I designed a new one as a spare part. ...This clip fits for the ribbon cable on the right side of the extruder.

A simple clip to hold together two 1mm x 10mm ribbon cables (allows for 2mm x 10mm dimension)

I liked the ribbon cable clip by https://www.thingiverse.com/thing:2774999 However I wanted one that fit both cables from the prusa mk3 so that I could hold them flat under a shelf. Therefore it is a bit wider accommodating both cables without...

Ribbon cable failure due to flexing at the connector is undoubtedly the most frequent cause of M200 malfunctions. This design securely attaches to your Z-Temp's housing, effectively eliminating cable flexing at the connector. ... Print Settings Printer:...

Summary: Ribbon cable failure due to flexing at the connector is likely the most frequent M200 malfunction. This design snaps securely onto your Z-Temp's housing, preventing cable flexing at the connector. ... Print Settings: Printer: Zortrax M200...

CR10S PRO Ribbon Cable Cover v2 is the improved version of the cable clip. ... I added tabs to ensure the clip stays securely clipped in once installed.

CR10S PRO Ribbon Cable Cover v2 is the improved version of the cable clip. ... I added tabs to ensure the clip stays securely clipped in once installed.

The inspiration behind this innovative design comes from WaveSupportApparatus's Ribbon Cable Clip for Raspberry Pi Camera and Scott_3D's T_Slot_Cover. This versatile clip offers a convenient feature: it snaps securely into the T-slot while still...

 As you can see in the photos, the ribbon fits with a little more room to spare.I also found the ribbon was a little hard to thread between the hooks at the end of the clips.  So that has been widened a little.Finally, I used hammer head t-nuts...

RIBBON Jetclass

Xmas ribbon

Пуф Ribbon

After installing BLTouch on my CR10S Pro, I did not find a cable clip for the cables from the sensor along the ribbon cable that I liked. ...So, I created my own.

Use double sided tape to glue it somewhere. Tinkercad Source Print instructionsPrinter Brand: Prusa Printer: i3 MK3 Resolution: 0.2mm Infill: 20% Filament: Prusa PLA silver Use a brim to ensure bed adhesion, use a scalpel to remove the brim in the...

Needed a long cable (1m normal Pi camera ribbon cable) but connect to a pi zero. Could not find a 22 to 15 pin cable that was over 300mm. ... From remixed part is a great idea - just added grooves to line up the ribbon pins.

Six assorted clamps for flat ribbon cables on the 20x20mm nut profile six. The image shows the Tronxy X5. ... 1.2 mm wall thickness.

Thought the initial concept was on the right track, but recognized a clear opportunity to develop a simple solution to manage dangling ribbon cables.

A quick and simple fix for you Ender 3S1 series printer, which eliminates the stock issue where the ribbon cable crunches while homing. I took the basic concept off of Printables (user and product linked and tagged below) and custom made this...

... parameters. ... Included STL of a clip that fits the Raspberry Pi Camera ribbon cable. I used it to route the ribbon cable from the PiCam in my Lack enclosure, with the camera itself mounted on this project: https://www.thingiverse.com/thing:3722611

A Clip that gives the extruder ribbon cable extra support , Dose not pinch cable and lets it have some movement to reduce stress on wires and Does not interfere with normal printing. ...Slides on just like original clip

Well, standard Extruder is not really running smoothly without a special fan duct as well as a ribbon cable holder. I designed a new riboon cable holder. ...Fanduct as well as vent clip from Humebeam.

3D model of Ribbon Tree origami style with all procedural toons shaders for blender render cycle.

This is a simple cable clip I created to route Raspberry Pi camera ribbon cables. Attach to a surface using double sided tape, and the cable clips right in. ... It has a little wiggle room, so you can even hold a few cables in one clip (or double back...

... moving the clips apart. Put one cable in and the then the other. Per #1 Print a clip and a bracket. Per #3 Screw the two parts together with an M3 12mm screw. Per #5 Slide the cable clip and bracket into the T-slot. Category: 3D Printer Parts