3d printer ribbon cable

Simple ribbon cable clip (15mm) I designed for my screen cable. Can slide cables in and out of it with the small cut out. ...Small screw needed to secure to whatever it is you need your cables securing to

I made a simple chain-style cover for Raspberry Pi camera ribbon cables. This project involves connecting a camera module directly to a printer's build plate, allowing for high-quality photography of printed objects. To get started, I added a remix...

I crafted this to securely fasten the substantial ribbon cable utilized with the SD card Expansion on my Ender 3. ...It is tailored for use with 2020 profiles.

After installing a drawer, I needed to run a ribbon cable across a piece of 4040, rather than parallel to it. ...This clip worked nicely.

I used this to route the ribbon cable from the PiCam in my Lack enclosure, with the camera itself mounted on this thing: https://www.prusaprinters.org/prints/100683-articulated-picam-mountPrint SettingsPrinter:  Prusa Mk2Rafts:  NoSupports:...

This is a simplified version of my other ribbon cable support found here: http://www.thingiverse.com/thing:1680656. This one prints faster and easier, requiring almost no support material. The angled design may be better suited for rear-mounted...

This is a compact Ribbon Cable Clamp that securely clips onto the stock Extruder cover without requiring any modifications. You will only need two M3 cap-head screws and two nuts to install it. ...To add extra protection, I applied a strip of felt to...

I made this ribbon cable clip to hold the cables to the frame, when having the LCD mounted on top.It uses 2x m3x10 screws, to screw into the existing holes in the frame.

......One is to clip the bowden tube to the ribbon cable the other is to clip both cables together for better cable management. What makes them better? I found the other ones were always slipping off the ribbon cable because the opening was at the end.

This custom-made clip holds a raspberry pi camera ribbon cable in place, allowing users to attach it without disconnecting any components. Its straightforward design enables seamless integration of the clip onto the cable. To secure the clip firmly...

I had trouble stuffing the cable Prusa display ribbon cable in the 30mm extrusion during assembly. I thought up a ribbon cable holder that fit the extrusion. So I made one as my first test of Atom3D and Prusa design to print process. Made with Alibre...

I designed this thing specifically for 15mm wide ribbon cable, just like the display cables used on Anet A8 LCDs. Secure the guide to your case using 8mm wood screws and slide the cable behind it. ...The design should be springy enough so you don't have...

Presenting the Pi Cam Ribbon Cable Support device to hold your ribbon cable and can be used for time travel (that feature is still in testing).\r\n\r\nWorks great with Pi_Camera_2020_Adapter, Pi_Camera_Back_Adapter and Pi_Camera_Back_Tripod from...

I am printing in ABS and did not want to fry my sd card in the enclosure, this is an easy way to stick your sd card and ribbon cable somewhere it is not exposed to intense heat

Two cable clamps secure the 16-way ribbon cable running to the Extruder head, keeping its route tidy and organized. This simple solution greatly improves the overall appearance of the setup. ...To ensure a stable fit, two cable clamps are required,...

It's also a better fit when using the Z-Mon filament monitor clipped to the ribbon cable. Print Settings: Printer: Zortrax M200 Rafts: Not necessary Supports: Yes Resolution: 290µ Infill: Whatever works best Notes: Since it's a snap-on design, it...

The cable I had wasn't quite long enough, but I had another ribbon cable that would give it enough length. I laid the two ends on top of each other and used electrical tape to hold them in place, but that didn't give it a strong enough connection...

cable cover in two versions, narrow and wide.The advantage of this chain is that the same ring is printed for the whole chain (the ring is made of a single component).

cable cover in two versions, narrow and wide.The advantage of this chain is that the same ring is printed for the whole chain (the ring is made of a single component).

... a fantastic machine, with minimal room for improvement. ... I managed to secure the LCD ribbon cable inside the extrusion, keeping it neatly tucked away from view. ... A few clever adjustments held the cable firmly in place, eliminating any loose ends.

Cable holders for aligning the ribbon cable for the CR10 Max. One end attaches to the lower V slot in the base profile and the other one is secured with an M4 bolt and a T-nut. ...For best results captive M4 slot nuts are recommended.

I Lengthened Dhatw's Design to Accommodate a 26-Way Ribbon Cable (33mm) Dhatw's original design prints flawlessly, even accommodating a 20-way cable. I simply extended its length without altering any other aspect of the design. ...After printing, this...

Customizer for Holder Clips for Flat Ribbon Cable Engineered to defy conventional printing methods, this design appears inverted, with excess plastic visible above the cable. To optimize its appearance, simply trim away unnecessary sections. ...Alan...

A 15-pin ribbon cable connector is designed for use in various electronics, facilitating connections between devices through the use of a thin, flexible cable with 15 pins. ...This connector type offers multiple points of connection and is commonly...

I designed this ribbon cable clip to secure cables to the frame, ensuring a clean setup when mounting an LCD screen on top. It relies on 2 x M3x10 screws, which are screwed into existing holes in the frame for stability. ... Initially, I attempted to...

On my lack enclosure I use a ribbon cable to connect my Raspberry Pi to my touch screen running Octodash.  I needed clips to mount the ribbon cable to the bottom of the lack table.  I printed them in PETG because it needs to be flexible for...

This is a straightforward Ribbon Cable Clip that is effortless to put in place and take out. It merely clicks into position for installation. The clip features an elongated tab that can be effortlessly grasped with one's finger to dislodge it. ...Print...

I made the following modifications to create a more practical and visually appealing clamp: - I added a slot that allows for easy mounting without having to disconnect or reconnect the ribbon cable. - The mechanical strength of both vertical towers...

The cable I had wasn't quite long enough, but I had another ribbon cable that would give it enough length. I laid the two ends on top of each other and used electrical tape to hold them in place, but that didn't give it a strong enough...

To use this cable clamp, adjust it so that the cable support is parallel with the ribbon connector and perfectly aligned with the back edge of its opening. That way the ribbon will enter the connector perfectly straight, without any strain on the...