3d printer rc plane

A tail wheel frame for my Hobbyking Hummer.

Pilot's Station for Remote-Controlled Aircraft with Empty Instrument Panel This pilot station is engineered specifically for a scaled-down version of the Space Walker model aircraft.

A revolutionary new aircraft, crafted from ultra-lightweight balsa wood, relies on advanced lipolymer batteries to propel its mighty 1,400 kilowatt DC motor to remarkable speeds.

Handheld Remote Control Aircraft Mount Designed Specifically for Turnigy 2200 Kv Motor

A custom-built vortex generator, specifically engineered to achieve maximum aerodynamic efficiency, is being implemented at an angle of precisely 20 degrees. ...This innovative design draws direct inspiration from the comprehensive guidelines outlined...

Follow Experimental Airlines AXON model (as demonstrated on U Tube) with an allowable weight of 1300g. Print using 5-8 shells and adjust infill level between 40% to 60%. Set layer height at 0.15 for better quality. Attach axel collars to the 4.5mm...

This is a fully adjustable and straightforward holder for your radio-controlled airplane. ...I wasn't pleased with suspending mine from the engine, so I chose to create one instead.

Create slots in foamboard for scratch-built aircraft using a 1-2mm width; fill with hot glue or any available adhesive. Ensure maximum strength by printing at 100% infill. ...Note that the hole size is 1.5mm in diameter.

To install the engine mount on the Axon FPV flyer, place it within the square tube. ...This component is relatively insensitive to layer height and shell count; try printing it with four shells and a 30% infill for optimal results without any issues.

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

The humble Wheel Holder - a steadfast companion for securing models during transportation or when proudly displayed on a shelf. ... Crafted with precision using OpenSCAD, this ingenious device is not only functional but also infinitely customizable,...

Two sleek concepts to elevate your aircraft's aerodynamics effortlessly.

Have fun

This is a back plate that i made to replace the spinner backplate on my CMP spitfires 85mm spinner after it broke the studs the screws screw into. can be printed in any material, but probably strongest in ABS or PETG. ...2 models are included one with...

The aileron system of an airplane is a critical component that affects flight dynamics and maneuverability.

People are using 20mm plastic conduit for a simple wing holder that costs almost nothing from Screwfix, a very useful store. ...It performs admirably even with subpar materials.

I've specifically crafted these pants for the Hall Bulldog Racer model boasting a massive 1200mm wingspan. Measuring approximately 180mm in length, they boast a spacious compartment to accommodate a substantial 60-70mm wheel. ...Initially tested with...

I've Included Both a Flat Bottom and Curved Version The Curved One's Located on My Phantom FX-61, While the Flat One's Mounted on My Hazzard FPV 29-Inch Flying Wing. ... This Setup Suits a 40-Millimeter Launch Ring.

Hello, This is upgraded motor hanger for LRP upstream or bixler so its universal motor hanger. It's better to be printed with Petg or stronger plastic not PLA but it's not the worst chose. ...

Nylon pinned hinge 16x28.5mm.Model was made with FreeCAD

A University Assignment Task Project at University University-Based Task Assignment Task for Uni Project College Work: A Project An Academic Endeavor: The University Project The University Work - A Project Uni Assignment: The Project ...

Publish your work and enjoy the thrill of creation!

<p>These are some of my favorite wheels for Slow Stick FPV – they are large diameter and light and roll great in the grass as you can see in the video below.</p><p>Print the tire using TPU with 0 (zero) infill and double wall.</p><p>I used Sainsmart...

This model is designed by Tinkercad. ...Modify it live at https://www.tinkercad.com/things/4PSkCBtA1rF.

This is a re-upload since the original files were deleted for some unknown reason. Quality: The layer height is set at 0.2 millimeters, ensuring high print precision. Shell: A wall thickness of 0.4 millimeters provides optimal structural integrity....

Multiplex Minimag RC Plane Landing Gear Holder for Replacement When Damaged. ... This landing gear holder is designed to serve as a replacement part for the Multiplex Minimag RC plane in case the original one gets damaged.