3d printer power supply fan

This is a versatile fan holder designed specifically for the Anycubic Prusa i3 power supply unit. Unfortunately, I found it lacking in one significant area - it does not come equipped with any cooling features. However, its purpose is quite...

Mounting a 120mm fan to a standard 12-volt power supply is an uncomplicated process that requires minimal tools and expertise. Begin by locating the mounting holes on the back of the power supply, which are specifically designed for this purpose.

Simple remix of JOulz Ender 3 Power Supply FAN Case 80mm. ...I wanted to integrate a fan grill into the same print so it would be less trouble printing it separately.

This is power supply modification for ender 3 pro. ... You need to remove the original cover and replace it by new cover with 80x25 12v fan The frame and the cover mounted by screws from fan.

A custom cover designed specifically for Anet A8 power supplies enables easy installation of a 120x25mm computer fan. This specially crafted accessory allows users to secure their cooling system directly onto their power supply unit. ... UPDATE: For the...

I fabricated a customized power supply cover to swap the noisy 60mm low profile fan for an 80mm standard one. Be aware: Only use this type of component if you are highly skilled in electronics and familiar with working safely with high-voltage parts,...

This part is specifically designed for a 12-volt, 40-millimeter fan that comes with the original Anet A8 power supply. ...I'm using PLA exclusively and only require supports where my build touches other parts.

Just another essential accessory for the Ender 3 Pro's noise control system. ... Never attempt to remove both screws simultaneously, as this will cause the fan to fall directly onto the power supply casing.

It´s a Power Supply Cover with a 92mm Fan Mount for the small Edition of the 350W Power Supply maybe it doesn´t fit exactly !?! I have the Version 1 installed and this doesn´t fit. ... but i have fixed it with a cutter blade the old version dont...

Your initial design and construction features a fan baffle that attaches to the side rail, effectively obstructing the power supply fan from blowing on the build plate's underside. Additionally, it prevents any debris from falling into the power...

This fan shroud directs airflow away from the print bed on Anet A8+ power supplies, resolving quality issues with prints, especially tall objects in vase mode. It also reduces noise from the power supply fan as an added benefit. I observed similar...

The internal power supply fan (not the power supply case fan that needs 24V) runs off 12V. I spliced two Noctua fan connectors to run off this 12V header. 4. All three fans are spliced together to run off of 1 of those Noctua fan connecters from...

This is the duct for the Ender 3 power supply. ... The power supply is placed on the side of the printer when creating a thermal casing. ... An air duct is needed to direct air to the non-working side of the printer.

This is a creation of multiple ideas into a one piece print for those wishing to have a fan silencer shield and tool holder onto there stock Ender 3/3 Pro power supply.Also, this was designed to be a snug fit or something you can mount to your power...

This is a custom Double Fan Case designed specifically for the Ender 3 Power Supply. It's engineered to accommodate both the original fan and an additional 80mm fan simultaneously. I created this project in response to my existing fan being too loud....

Slim minimalist PSU Fan cover for Creality Ender 3 3D Printer.

Another quick design for the Power Supply Fan Cover of an Ender 3 printer. It takes roughly four hours and ten minutes to print at a layer height of 0.2mm. Make sure to adjust the Retraction Distance to 6mm, the Retraction Speed to 25mm/s, and toggle...

I discovered that the power supply was re-routing the input, so I decided to redirect the warm air flow away from the electronics and will add a general case fan for enhanced cooling. The version in the picture had some issues which have been...

Work in Progress - Not Fully Tested Yet This is a custom-made fan duct designed for my 24V33A Power Supply. The existing fan is notoriously loud, so I'm replacing it with a 120mm Noctua fan to significantly reduce noise levels. To accommodate the...

This model is based on this model https://www.thingiverse.com/thing:3155772 I really like the look of the base model and could not find something similar for the power supply fan. The remix is my first ever remix and is made to cover the power...

This is a remix of Case Fan (80x10mm) Anet A8 Power Supply by Black-Demon\r\nhttps://www.thingiverse.com/thing:2043548 V.1.1: Bug fixes were made to ensure a smoother printing experience. I had an 80x25mm fan and wanted to attach it to the power...

------- A protective cover for the Creality Ender 3 power supply fan, securely mounted using stock screws. The cover redirects airflow upwards and away from the fan. Printed without supports. ... When installing, carefully remove one screw at a time to...

When installing the fan, position it so that it draws air in and expels hot air away from the power supply unit. This design accommodates a 50mm box fan. ...A second version was added to fit an 80mm fan; however, this one has not been thoroughly tested,...

I used OnShape to create this power supply fan for my Ender 3. It is specifically designed to save filament at .28mm resolution with a 20% infill. Just print the part and place it over the fan opening. ... > <strong>Note:</strong> I am not an airflow...

I've remade a 120mm fan mount for the Anet A6's power supply, trimming unnecessary parts to speed up production and conserve filament. ...I've also relocated the fan upwards, as that's where my PSU tends to get hottest.

Clip on fan duct for the power supply unit of the Creality Ender 3. No tools needed, simply slide it on and enjoy immediate results. This clip-on solution is designed to silence at least 80% of the fan noise, making it ideal for users seeking a...

... around a 90mm fan. ...Four robust M4 fan screws are holding it firmly in place. Additionally, one versatile M3 screw provides further stability. The power supply unit, as depicted in the accompanying image, is another key component of this system.

... adapter: 6x M3x8mm. ... This mod must be used with CR6-SE Power Supply Noctua NF-A6x25 Fan Adapter : https://www.thingiverse.com/thing:4685799 This mod is the same thickness as CR6-SE Motherboard Fan adapter : https://www.thingiverse.com/thing:4685267

I thickened up the parts in V2 to make sure they print smoothly. ...Since no 92 mm fan adapters were available for the Anet A8 power supply, I made one myself. Hopefully it will be useful to you! ...I also added a cover for thicker 33mm fans.