3d printer part cooling duct

A universal part cooling fan duct designed to accommodate 25mm, 30mm, and 40mm fans is available, featuring a compatibility with the majority of standard Tronxy hotend covers that require only one 3mm screw for installation.

Replace the original text with the following rewritten text: Humans install a part of a cooling fan duct that is printed in layers just 0.2 millimeters high at speeds of 35 millimeters per second.

Note: The "Standard Version" can be found here: http://www.thingiverse.com/thing:2217394 This part cooling duct and nozzle is designed for use with a Tevo Black Widow 3D printer and a 40mm fan. A file for a compatible velocity stack is also included....

Great-looking part cooling duct, secured with a clip to keep the fan wires in place. Printing flawlessly and all credit goes to Rocco81-92 for designing an excellent system. Visit https://www.thingiverse.com/thing:2751027 for the hotend duct and...

This is not the most advanced or optimised part cooling fan but it does the job pretty well.Replace the standard E3D fan duct with this and you will be able to add a 40mm radial fan as a part cooling fan. Remixed from the original :...

This is not the most advanced or optimised part cooling fan but it does the job pretty well. ... Replace the standard E3D fan duct with this and you will be able to add a 40mm radial fan as a part cooling fan.

... find the "easy fit" duct sits too low on a standard e3dv6, please let me know and I will try to make a few more adjustments. It sits several mm above my tungsten nozzle, so Ithink it should be OK with the stock nozzles. Category: 3D Printer Parts

The E3D Clone hot end mounts a lot lower so the stock part cooling fan ducts blow on the hot end and not at the nozzle. This uses the stock fans and mounting and you replace the existing fan duct. Check the photos for the suggested print...

The photos clearly show the dramatic difference that this part cooling system makes; those prints differ only by the application of the system. Ideally, one would modify the Repeiter firmware to use the control line going to the extruder fan to...

... This remix fixes several problems with the original design and improves airflow, which only cooled one side of the part. I added internal vanes to direct airflow all around the duct. The casing of the duct was reduced, allowing space for the LEDs.

simple part cooling fan duct for the biqu h2. the titan 6015 radial fan is fairly quiet and moves a lot of air. its angled forward to account for the hot end fan exhaust and it also smoothens the airflow a bit. now i rather have problems with too...

I wired the three 5015 fans in parallel with the part cooling fan so they turn on and run at the same percentage as the part cooling fan. ... These are the blower fans it was designed around:...

I tried to remix this great part cooling duct to make it work with 5015 radial fans and this is the abomination that came out :) There's a version for the stock hotend mount and one version for this 40mm hotend mount:...

A small box I designed to hold small screws, thermistors and other printer parts.

A simple fan duct for part cooling of BMG and E3d V6 Hotend direct drive(no bowden) setup with 5015 blower Fan. I made this standalone so that you can just hook it up with BMG itself. The duct is also modular if you wish to print it with other...

HevACS type of ducting works quite well when the hot-end is not moving in the Z-direction, which is not the case for Ender 3 and most other Cartesian printers. So I need to attached the outlet or the whole fan/duct assembly to the X-extrusion. After...

Standard version can be found here: https://www.thingiverse.com/thing:2211870 This part cooling duct and nozzle is for use with a Tevo Black Widow 3D printer and a 40mm fan and Volcano nozzle. Use with this velocity stack:...

Yet another part cooling fan duct for the Anycubic i3 Mega S (should work fine for the non-S Mega, as I believe they have the same fan and X-carriage cover. I recently upgraded the hotend to an E3Dv6 and due to the geometry when its installed, I...

This printer uses 3D printed parts and joints that hold together a hand-cut 1/2 inch thick plywood frame. The printer is still a work in progress, so improvements and file changes are likely before I'm finished. Specs (as of now): * Build volume:...

I created a duct piece for installing the cooling fan, by attaching the hotend mount section, and made it functional as before. ...The design now includes a sufficient airflow area and precise spacing to ensure no contact with the stationary build plate...

x2 m4 8mm Bolts x2 m4 Nuts x2 m3 10mm Bolts I designed this for my Ender 3 V2 printer, but it should fit most creality 3D printers. Including the CR10, Ender 2, Ender 5 ect... This is because it attaches to the same place as the hotend and does...

This content serves as an addition to the instructions for my teacher's 3D printer.

This is a duct for the Longer LK5 Pro which uses vanes to better direct the air from the stock axial part cooling fan, as shown by Alex Kenis ([LINK](https://youtu.be/SX-okOHvh1Q)). However, from my testing, it didn't make any measurable...

Instead of adding more fans on the printer head where it adds weight and make it sometimes ugly huge to be effective, this puts the blower on the side of the X axis beam and so it isn't putting any more weight on bad places while still adding much...

Anycubic I3 Mega Part Cooling Fan Duct for Sunon MF50151VX-B00U-A99 or MF5015V1. The design draws inspiration from two existing fan designs found on Thingiverse, specifically [this](https://www.thingiverse.com/thing:3553164) and...

This is a remix of deepfreideyeballs's 5015 part cooling fan duct. His duct has been modified to nicely fit on the Biqu H2 V2S lite. See attached photos for fitment. Also, I added a cylindrical column for added strength and beefed up some thinner...

Final version of my combined tube- and radial part cooling fan mount for JGAurora A5, now equipped with a robust radial 50/15 blower fan that replaces the inadequate axial part cooling fan. To ensure reliability, I have added strain relief to both...

This is a mix of the Prusa Mk3 style part cooling fan duct, I have added the BLtouch mount to it. there are two variants v2 has the BLtouch mount as far back as it will go and was the case when using the BLtouch mount separately. ... V3 has the mount...

This is a remix of 3DFreezeMe's part cooling duct (https://www.thingiverse.com/thing:4818990) that works with his extended Orbiter mount. The only change I made was to add a bracket for extra stiffening, as I found the original vibrated and bounced a...

This is a counterpart to https://www.thingiverse.com/thing:4064197, featuring a duct for a 6048 blower-style cooling fan mounted on the left side of the extruder carriage and pointing down, roughly in line with the heat blocks. It's designed to be...