3d printer part cooling duct

Cooling duct for smaller 30mm fans. ...I needed this for my Frog direct drive extruder which uses a smaller than normal fan.

cooling duct for Mosquito hotend from Slice Engineering. inlet is a 4mm (1/8") air nylon line. ...pressure or air flow restrictors have not been tested yet.

Cooling duct for smaller 30mm fans. ...I needed this for my Frog direct drive extruder which uses a smaller than normal fan.

Additionally, download the extruder cooling duct from the link given in the original source. You'll need to connect wires from the blower fan and plug them into the K-fan slot on the control board, allowing you to adjust the cooling fan speed using...

Create an easy-to-print, 40mm fan duct for your Rostock Max 3D printer using OpenSCAD. ...Print it in PLA without needing support material, then secure it to the platform with three cable ties threaded through its top holes and air outlets (as shown in...

Here's a split cooling duct that leverages the stock 30mm fan supplied with E3D V6.\r\n\r\nThis setup caters to those who crave print cooling without needing an additional or new fan. ...\r\n\r\nWhile it may not be the most effective solution available,...

I designed this duct to match the dimensions of the stock one, but with two small posts added to help hold the duct in the proper shape and posiiton when installed. Just poke the posts into the unused fan mounting holes. I also put a small...

This is just a small duct to redirect the air coming into the main cooling fan for the stock head of the Ender 3. This is just to change the airflow to pull cooler air in that hasn't been heated by the bed. This is by no means a necessary upgrade...

The Remix of the Galaxius Cooling Fan Duct was engineered specifically for the Robo3D, incorporating a complex internal design that utilizes loft geometry to expertly optimize airflow circulation patterns.

To address this challenge, I've added a cooling duct and rear fan mount, which ensures that the motor remains at room temperature or slightly above. The 40x40 mm fan should be oriented so that it pulls air out of the duct through the grilles on each...

My simple and efficient design of a cooling duct for a common hotend with a 40X40 mm fan. My Prusa i3 cheap clone had only a fan to cool the hotend, but was not very good and had limited my printing temperature to 200C, now with my v1.1 design, i...

... two holes to use a ribbon to keep the fan securely in place. The duct height is adjustable, offering about a 4mm range to achieve more precise cooling targets. ...Other materials included are: 2 M3.5-10 screws, 1 M3.5-40 screw, and 3 M3.5 nuts.

... in place using a ribbon. The duct's height is adjustable, allowing it to be set within an approximate range of 4mm for more precise cooling control. ... Additional materials needed include two M3.5-10 screws, one M3.5-40 screw, and three M3.5 nuts.

So I tried to put more holes to cooling duct model to improve airflow. Im not sure if it helps or not while I made also lot of changes in prusaslicer, but curretly Im able to print my models without problems. The only problem with “Prusa Mini...

These objects replace the poor stock nozzle cooling system provided by FLsun.You will need 2 x M3-20 mm bolts and nuts to mount the fan along with the fangrid.Support is not needed to print these objects.This object main web page...

2 rear cooling ducts to mount a 120mm cooling fan on the rear to exhaust hot air if adding a Nvidia 2700s or hotter. Tested with a rtx 2700s and rtx 3080. 1 short and 1 long, short one is the second iteration and the one to use I suggest. ...

... and 15% fill without raft or support. Be cautious with bridging over ducts; try turning it off and changing the solid layer angle to 90 degrees. ...Don't forget to clear any "spaghetti" in airways and remove chrome fan guards (fan bolts are M3-10).

I've owned my Voxelab Aries for 2 weeks now (as of this writing) and one of the first things that needed improvement was the filament cooling duct. The original isn't that bad but it doesn't blow the air where it's needed the most, concentrated below...

... fan, along with the fan grid. Printing these objects does not require support. The main webpage for this object is located at http://www.ctheroux.com/flsun-cube-nozzle-cooling-duct/. ...On this page, you can also request access to the source files.

My remixed for my Cooling Setup https://www.thingiverse.com/thing:4553114 This is completely redrawn from his design.... There was a lot of problems that need to be redrawn to make it work for my cooling system..... But can be used on it's own...

Cooling duct layer for Anet A8. The compression cone directs and increases the air pressure in the nozzles that are oriented to the deposited material, so that it does not cool the extrusion nozzle but the layer of material. ... Designed specifically...

I've owned my Voxelab Aries for 2 weeks now (as of this writing) and one of the first things that needed improvement was the filament cooling duct. The original isn't that bad but it doesn't blow the air where it's needed the most, concentrated below...

Custom of prusa rework i3

Design Features - The Tuct Tunnel uses aerodynamic principles of aircraft airfoil to enhance the flow of cooling air in air tunnels. ... - New ducts use silicon air tubes to prevent heat dissolution at the heatend and to be flexible in collisions with...

... too low. Unfortunately, it still doesn't sit high enough. Print Settings: Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.2 mm layer resolution Infill: 20% infill Notes: I added supports to the back side where the vent connects to the fan.

This is a versatile cooling duct designed to clip seamlessly over the 40mm fan of each extruder carriage, making installation and removal effortless whenever needed. No additional fans or wiring are required, streamlining your setup. Screw holes are...

... requiring adjustments to avoid hitting the ends or modifying the endstops. Feel free to provide any comments or suggestions you have! Join our discussion at http://umforum.ultimaker.com/index.php?/topic/5108-dual-fan-duct-anular-cooling-system/.

... over ducts by turning off bridging and changing the solid layer angle to 90 degrees. Don't forget to clean "spaghetti" from airways. The short fan-to-duct bolts require M3-10, while M3-60 bolts replace the original ones as duct-to-extruder bolts.

# Horns Duct V2 - Layer Cooling ## Utilized In: - Unseenmaker's remix, available at https://www.thingiverse.com/thing:3924864 (check it out) - Small Footprint Titan Aero (https://www.thingiverse.com/thing:3600079) - Low-X Titan Aero...

My first attempt at merging two different fan ducts into one to create a better cooling duct for my Anycubic Kobra.I have uploaded a “2mm offset” version of the stl file, in that file I nudged the main duct portion 2mm to attempt to find better...