3d printer flashforge

Sorry I use a french Win10Pro, so the translation will not be the same On win10 -> This PC -> Connect a network drive Use the last line "Connect to a web site ..." a few next next next after Enter : http://FlashForge/3D with FlashForge = Your APPNAME...

This is the first printer in my model series 3D printers where I Model 3D Printers from scratch The Flashforge Adventurer 3 is my personal 3D Printer and is fully enclosed. the thing hanging out like a door is the door. ...I made this from scratch in...

Print Settings Printer: CTC Bizer (Replicator Clone) Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 30 Notes: Print with 2 shells and at minimum use ABS | Roof and floor height - 1mm | Layer height - 0.2mm | 30% infill with a linear pattern...

This is a model of the Flashforge Finder 3D printer. 

So the Finder will not be able to sense when the spool runs out of filament and pause the 3D-print. If you are looking for a product that is not available, please contact us. To learn more about the FlashForge Finder and support. ...Please contact us...

Supporting the filament, the spool holder is an essential component utilized by the FlashForge Creator Pro 3D printer.

... be more than 2.5 mm thick. Print Settings Printer: FlashForge Creator Pro/ FlashForge Dreamer/ FlashForge Guider/ FlashForge Finder Rafts: Doesn't Matter Supports: No Resolution: 200 microns Infill: 15% Notes: 5 top layers and 5 bottom layers.

This is a model of the Flashforge Dreamer 3D printer.

This is a model of the entry level Flashforge Finder 3D printer.

This is a model of the entry level Flashforge Finder 3D printer. Print Settings Printer Brand: LulzBot Printer: TAZ 5 Supports: Doesn't Matter Notes: Rotate model 90 degrees on the X axis to minimize supports Category: 3D Printers

This is a model of the Falshforge Dreamer 3D printer 

Print a 3D printer - Flashforge Finder Mock-Up.

... replace broken ones on the back wall of PowerSpec Ultra 3D printer. ...Print Settings Printer Brand: PowerSpec Printer: PowerSpec 3D Pro Rafts: No Supports: No Resolution: .2 Infill: 25% How I Designed This I designed the part using Autodesk Inventor

I got my FlashForge Dreamer 3D printer recently. After few searches did not find a right hook for my GoPro camera and decided to make it myself. a) the straight mount is taken herehttp://www.thingiverse.com/thing:123878 b) the hook designed myself...

Accessory to prevent air from entering the Flashforge Creator Pro 3D Printer port

This accessory lets you attach a 30mm-hole spool to a CTC or Flashforge 3D printer. It's my first SketchUp drawing attempt, with more photos coming soon. Check out this video: http://youtu.be/B6HgoJb__j8 For assembly, print the NUT thrice - once for...

Designed to perfectly fit FlashForge Creator 3D printers, this clip prints as two separate pieces that can be easily snapped together to create a hinge with just the right amount of resistance. The clip file also comes with a snap bolt that is...

This is a remixed version of the External Spool holder for the FlashForge Finder 3D Printer by CreativeTools. This version allows you to mount the spool holder on the side of the machine. It prints in one piece on the FlashForge Finder, just have...

FlashForge Dreamer 3D printer hook for filament. I have created hanging hook for Nunus 1 kg filament which is not fitting inside the printer's cabin. I started from another prototype http://www.thingiverse.com/thing:938750 I have than designed and...

This is an external spool holder designed to interface with the Flashforge Inventor 3D printer. It may also work with the Flashforge Dreamer and the Dremel Idea Builder. In order to complete this project, you will require a 5/8 inch round wood dowel...

This is an external spool holder designed to interface with the Flashforge Inventor 3D printer. It may also work with the Flashforge Dreamer and the Dremel Idea Builder. In order to complete this project, you will require a 5/8 inch round wood dowel...

This is a filament spool holder for Robo 3d Printer Filament used on the FlashForge Creator Pro. Although the spool holder was completely re-drawn, it was based on http://www.thingiverse.com/thing:930910 and we are inserting KDan's holder clip again...

This is an external spool holder designed to interface with the Flashforge Inventor 3D printer. It may also work with the Flashforge Dreamer and the Dremel Idea Builder. In order to complete this project, you will require a 5/8 inch round wood dowel...

These corner brackets were designed to interface with the Flashforge Inventor 3D printer and the glass plate upgrade from Flashforge USA. Supports glass dimension (L x W x H) 9 x 6 x 0.15 inches. Glass must be installed on top of the Flashforge build...

These corner brackets were designed to interface with the Flashforge Inventor 3D printer and the glass plate upgrade from Flashforge USA. Supports glass dimension (L x W x H) 9 x 6 x 0.15 inches. Glass must be installed on top of the Flashforge build...

Models for printing: 1x Filament Feeder Head Support (3D Printed) 2x Dust Filters (3D Printed) 1x Active Cooling Fan Duct (3D Printed) Additional Parts needed: 2x M3-0.5 60mm, Class 12.9 Alloy Steel Internal Hex Socket Cap Screws 2X M3-0.5...

Due to the limitation of the spool dimension on the Flashforge Finder, I have decided to design an external spool holder. Every 1kg of filament could fit with this design.Every part on this design can be print with the Flashforge Finder.No glue...

Made for having the filament spool on the front of the flashforge finder, due to the location below my desk. ... Using the mod arm made by Sjakktrekk >>> https://www.thingiverse.com/thing:2587632 and using Tinkercad, a modded version of the phone...

... hitch for power cable and few more), I'm sure it will go. Just print and install on the printer. There are holes for fastening the fan. ...I reccomend you paralleling it's power to the right printhead fan, there is a small tooth to hitch the cable.

The filament spools I bought would not fit all the way onto the spool holder that came standard with my flashforge printer which have a 66mm x15mm spacer at their base. Unlike the spools that came with the flashforge which are countersunk to...