3d printer filament heater

I give you the 3D printed Sterling main spring forming tool...https://i.imgur.com/j04a7Tb.jpgIt is simply a grooved shaft set to the correct diameter and pitch of a Sterling main spring. The shaft is hollow, allowing you to slip it over a section of...

For the majority of items, the mesh origin has been set so that when you import these objects into your 3d editor of choice, they are positioned as they would be on the sample ships provided. When comparing parts, you’ll notice some ships and parts...

based on my mirror array experimentation here: https://www.thingiverse.com/thing:5158449 and https://www.thingiverse.com/thing:5162096 All of which is very much derived from the excellent design here:...

TL;DRA broken plastic part with less than 1 g has been redesigned and 3D-printed, thus avoiding 975g of garbage in the form of a defunct mixer.Machine to repairOur Siemens hand mixer MQ90001/02 broke about 3 years ago. Thanks to the repair contest I...

:-) Happy 3D printing. UPDATE (8/7/2020): The 1/4" drive cap does not work well in hard ground with a 1/4" socket driver - the cap strips out, or at least it does with PLA. I have hard clay for ground, but maybe for someone with softer dirt or...

For triangles, we also decided to not measure the length of the hypotenuse but rather measure the height and width of the imaginary triangle, to make it more defined in Solidworks when we would eventually sketch and make the 3D model. Our final and...

https://www.etsy.com/listing/1069103115/3d-printed-spinning-wheel-kit-complete?ref=shop_home_active_8&crt=1 Affiliate Links for the non-printed parts. ... 2 inch 5/16 lag bolt 5/16" x 2" Hex Head Lag Screws Bolts 10 PCS, 304 Stainless Steel 18-8,...

  A bit of extra info: Customizer is based on OpenSCAD, a program that can generate 3D models out of a set of instructions. A customizer file is just a .scad file with specific formatting. You can use any version of OpenSCAD to load and edit a...

I have used these types of magnets before and used super glue, 2-part epoxy, and 3D pen (to add a little plastic on the edges) with varying degrees of success. For the bracket I used 5-min, 2-part epoxy. I sanded one side of the magnet, placed a dab...

This push-to release mount for the Google Chromecast TV remote, stores the remote under a coffee table, and a simple push on it's obscured base, and it ejects the remote for easy access like this:As well as being a cool way to keep your able that...

There are several 3d printed threaded parts. The internal threads should be cleaned out with a 6mm X 1mm tap. If you don't have a tap you may be able to use a 6mm bolt with a groove dremeled into it. I haven't had to use a die to clean up the...

Cómo configurar los parámetros para personalizar la impresión del pomo “silla de montar” 2.1. Para poder personalizar el pomo “silla de montar” deberá tener instalada en su ordenador la aplicación para diseño 3D OpenSCAD. Se trata de un software...

 (The combined slop of the 3D printed parts will give you roughly +/- 0.5mm of tolerance on your cut.If you buy hex on sites like Online Metals that sell in 12" increments, then each 12" will get you two cut hex rods. Preparing the JigThe jig has two...

Scan the World is a non-profit initiative introduced by MyMiniFactory, through which we are creating a digital archive of fully 3D printable sculptures, artworks and landmarks from across the globe for the public to access for free. ...Scan the World is...

Hello !Wellcome to my little office with Prusa MINI +.I made industrial lamp with concrete base, retro bulb and soft pad made of recycled rubber.O.10 DETAILPrusament PLANo supports15%We will need: Concrete (fine concrete with small...

The purpose of this assignment was to develop our collaboration and 3d modeling skills to better prepare us for future, more complicated, projects. Assembly Instructions:  Constraint Box: Use the rectangle tool to make a 6 x 13 cm box, make sure to...

Specifically, the mouth utilizes inexact measurements, and inconsistencies in source models from the 3D printing process made it difficult to gain a good measurement. On the sketch, we measured the mouth to be 1.20cm from the side of the constraint...

PLA has an inherent shrinkage factor, and that varies depending the type of PLA you use and all the other many things that go into 3D printing. You may need to adjust your slicer to (every so slightly) enlarge or shrink the part. Z-axis dimensions...

...This is the mount for my Cord Carrier. Cord Carrier - This is pretty self explanatory. Print this with a 3d cubic infill somewhere around 10%. The angles are designed to print without supports. FreeCAD file included. Printed. Tested. ...Works.

I am using all 2040 V-Slot for this build, 4 - 2040x250mm lengths for the base parts connected with 3D printed brackets. You could also use standard corner, inside Hidden Corner brackets or L brackets. The Carriage X axis is 2040x500mm and carriage...

ESP32 DevKitC (v1 or v4 tested)...

This 3D printable enclosure was designed to mitigate those issues by allowing the cable to be wound up compactly and attached directly to the back of the Steam Deck. Once attached, all you need is a small USB-C pigtail cable to connect the adapter...

Cómo configurar los parámetros para personalizar la impresión del pomo en “U” 2.1 Para poder personalizar el pomo en “U” deberá tener instalada en su ordenador la aplicación para diseño 3D OpenSCAD. Se trata de un software libre y se encuentra...

 To your health!The Salud CO2 Monitor was designed to inform you of your local air quality in terms of CO2, while also featuring a long battery life and simple no-solder assembly.In addition to the three 3d-printed enclosure parts, you will...

Join our Tribe or Patreon to receive amazing 3D printable miniatures sets each month for a very special price! Save big on the complete Noble Alfar bundle, which also contains pre-supported files for each STL. Please check the images to see what it...

Join our Tribe or Patreon to receive amazing 3D printable miniatures sets each month for a very special price! Save big on the complete Raid at the Temple of Ifrit bundle, which also contains pre-supported files for each STL. Please check the images...

There are several 3d printed threaded parts. The internal threads should be cleaned out with a 6mm X 1mm tap. If you don't have a tap you may be able to use a 6mm bolt with a groove dremeled into it. I haven't had to use a die to clean up the...

The Greatest view this model has are opposite from the conventions or typical 3D models. All the juicy detail work is on the inside. The Babylon Project was beautiful to the eye, and yes, it’s a Diplomatic station. This isn’t. It’s a modular city...

The field is confined by a steel “yoke” that forms the bulk of the detector’s 14,000-tonne weight.CMS acts as a giant, high-speed camera, taking 3D “photographs” of particle collisions from all directions up to 40 million times each second. Although...

This update does not apply to AAP01 nozzles.But this would bend the nozzle spring and gives ware on the nozzle that is unwanted.https://youtu.be/3N8hDKkQq5k______________________5-5-2024Mag catch bar Partisan version added----------------------4...