3d printer enclosure temperature control

This have the added bonus that you can detach PSU from the holder.Now you are able to easily take the printer out of the enclosure for maintenance.Extruder/MMU2 Indicator for sideway printerMost Extruder Indicators are designed in 2D for front...

I always have a problem with the print starting again after the pause, and having the printer go right back to print where it left off. It always bloody homes itself and starts fresh so I have to kill the printer and start all over again. Print...

I added some inline sockets to the power cables so I can detach the cables and remove the printer from the enclosure without having to unplug the molex connectors inside the Rambo board. Again, this is optional. IMPORTANT: do NOT use cheap connectors...

https://www.youtube.com/watch?v=Qbh_FZMeCUw Full tutorial available here: http://makerholik.com/3d-printing/enclosing-3d-printer/ After an extensive search for a design to enclose my 3D Kossel / Delta printer, I decided to create one myself using...

The corner holders are assembled within the enclosure to secure plexiglass with M4 screws. All holes have a diameter of 4mm and feature an embossing of 10.2mm for neodymium magnets. I decided to create two sides that can be removed using the...

We found out that the enclosure dampened the found output of the FlashForge Adventurer 5M by 10 decibels, as well as acting as thermal insulation to hold in the build area heat! These are the wooden dowel lengths you will need to recreate my...

Minimalistic enclosure built with 50cm x 50cm x 2mm hobby glass panes made of polystyrene. The side and back panes simply slide into place. The front pane slides in at the bottom and clicks securely into position at the top. Taping the edges of...

Always use same side for straight cut.Always use bar clampsIf you find good looking small hinges - buy them, save timeUse ear protection (headphones with good isolation - ok)Use eye protectionUse lungs protection when sandingWhat could be done...

Minimalistic enclosure using 50cm x 50cm x 2mm hobby glass (polystyrene) panes. Side and back pane slide right in. Front pane slides into place at the bottom, then snaps securely at the top. Electrical pvc tape is applied to the edges of the panes,...

The bottom-door-frame parts BD1-BD4 and top-door-frame parts TD1-TD4 complete the enclosure. All these components fit seamlessly onto the MK3s. To assemble the device, use 2mm bolts to connect the bottom and top frames. Alternatively, you can...

Easy to make acrylic enclosure. If you can make it easier, remix it. Tools and materials I have used: ------------------------------------------- For starting and ending dremel cuts: ------------------------------------------------ *...

You created a safety cover for your office's UP Plus printer after it was relocated to an open cubicle. The cover is designed to be made using 6mm thick clear plastic, with corner, hinge, and door stop parts to be printed first. ...Assemble the...

This is a basic 3D-printed housing for the Raspberry Pi. The casing features four mounting points for screws. ...Additionally, it includes ports for a microSD card slot, a mini HDMI connection, and two microUSB ports.

I was in search of a secure transport case for my printer, and found the aesthetic of a flight box appealing. However, I also wanted to use the box as a cover for everyday use, especially when printing with challenging materials like ABS. Thus, I...

A fan mount and enclosure for a W1209 thermostatic switch.

This is a concept I've been exploring for a budget-friendly 3D printer enclosure, an absolute must-have for printing ABS while preventing PLA curling in winter. A two-tier greenhouse design seems like the perfect solution. The top tier isn't intended...

This is a temperature control panel for your 3D printer's heated chamber/enclosure. ...There is a small OLED display that can display information, along with two toggle switches to control different systems of the heated chamber.You might need to fine...

This is a new version of the temperature control panel for a 3D printer's heated chamber/enclosure. There is a small OLED display that can display information, along with three switches to control different systems of the heated chamber.There are...

It is compatible with : - Mk3s /mk2s panel control for Prusa3D - PanelDue 5i from Duet3D - Raspberry PI 3 1B+ / 2B / 3B+ / 4B - Kuman 3.5″ (GPIO) / Hyperpixel 4″ (GPIO) / Waveshare 5″ (DSI) - W1219 enclosure temperature control And more… Modular...

Create a protective enclosure for your 3D printer using just four brackets! Simply add L-brackets, and this will establish a stable environment with consistent temperatures that allows you to print with ABS and other high-temperature materials. ...These...

<p>This is a housing for one of those cheap temp sensors you get on banggood or whatever. I can't remember the model number I used or I would put it on here.</p> <p>I included a well ventilated space next to the display for a small circuitboard to be...

3D Printer enclosure ================ This is a universal 3d printer enclosure build from two IKEA Lack table. In the under table there are a filament storage for ten 1kg filament spools. In the upper table there are the 3d Printer. The filament...

This is a series of printed (PETG) parts that turn 4mm Marlon Corotherm (multi-wall polycarbonate - intended for clear insulated roofing and horticultural construction) into a 600x600x600 (internal) printer enclosure. Before you say it, I know, Prusa...

This is a series of printed (PETG) parts that turn 4mm Marlon Corotherm (multi-wall polycarbonate - intended for clear insulated roofing and horticultural construction) into a 600x600x600 (internal) printer enclosure. Before you say it, I know, Prusa...

Cheap DIY Tool drawers with LED Full digital Dynamic RGB LED lighting of Enclosure Remote control main power, each 3D Printer indvidually Monitor Humidity + Temperatures and control exhaust PWM FAN Tons of additional features like fire detection,...

3D Printer enclosure This is a universal 3d printer enclosure build from two IKEA Lack table. In the under table there are a filament storage for ten 1kg filament spools. In the upper table there are the 3d Printer. The filament run trougt the table...

This design is a remix of DrewPetitclerc's fantastic 3D printer enclosure. There are several notable changes: Designed for thinner 0.093-inch acrylic sheets. (Note: Drew's original design used 0.25-inch thick sheets.) This makes the design lighter...

Digital Thermometer MountI designed this simple case for a standard digital thermometer to be used with the 3D printer enclosure from enclosurelab.comThe excess cable hides in the back. Great for monitoring the temperature of your printer box. ...Since...

Digital Thermometer Mount I designed this simple case for a standard digital thermometer to be used with the 3D printer enclosure from enclosurelab.com. The excess cable hides in the back. Great for monitoring the temperature of your printer box.

This is a collection of goodies I created for my 3D printer enclosure: * First and foremost, a filament roller holder that's as easy to use as can be * A tiny tube that allows the filament to pass right through the table (on top) * A "Nuclear-style"...