3d printer drag chain

I designed a Drag Chain that can be printed with PLA you need to drill and cut 4x M4 holes for the Back Block. You also need to sinking(?) the holes for the 2 roller screws(M5x30). ... Screws you need: Countersunk Screw: 1x M3x25(Front Block) 2x M5x30...

I'm excited to share with you a design for a cable drag chain that's specifically tailored to the Tevo Tarantula, based on my semi-open drag chain concept: https://www.thingiverse.com/thing:2999958 One of the standout features of this design is its...

Amazon source for chain drag used in this design: https://www.amazon.com/Ake-Towline-Plastic-Replacement-Accessory/dp/B01IOZDA1I/ref=sr_1_2?s=pc&ie=UTF8&qid=1480308204&sr=1-2&keywords=chain+drag Ebay source for Molex connector:...

Additionally, the setup necessitates drilling two holes to secure the drag chain in place, depending on the chosen size of the drag chain. This particular mount uses:...

Because it's only one screw at that end, I designed a little support bracket which should snap fit around the drag chain on the the 20x20 aluminium extrusion. __FIY:__ The covers for the aluminium extrusion which you see in the background are...

Y axis end stop bracket: You may have to use this bracket to slightly move the limit switch to provide adequate clearance to the Y axis carriage upper bracket where the X axis drag chain mounts. Designed to use a 10x10mm drag chain. Yes it can be a...

 You can also print a second bottom bracket and install it around the middle of the rail (right under the back of the chain when the Y axis is moved all the way forward) to better support the chain.This design was intended for use with the "uxcell...

This is a cable chain for Zonestar Z6 printer. I´m upgrading my Z6 to Z6B (with heated bed). I designed both terminal links for the chain ( and modified a little bit the chain) to fit the cable port for the heated bed, and the table. I´m still...

 Klipper… 😂You will want to use this wonderful chain to connect from the stock extruder location to the new Y-axis bracket: https://www.printables.com/model/243893-semi-open-universal-cable-drag-chainI printed 18 links for my particular setup, your...

Consequently, I required a drag chain to neatly manage the cables. These are the mounting brackets that secure the components. One is designed to connect directly to a sturdy 1010 extrusion, while the other securely attaches to the same holes as the...

Remix from @diogosantos88 design and this https://cults3d.com/fr/mod%C3%A8le-3d/outil/ender-3-v2-satsana-bltouch-hotend-cable-chain-small-mount

I wanted a drag chain rear mount that wouldn't force me to drill into the chassis. This versatile mounting solution allows for both horizontal and vertical chain orientation, giving users maximum flexibility. Conveniently, a set of pre-drilled...

The new QueenBee Pro CNC router kit from Bulkman3D includes their drag chain kit with the purchase. However, this kit doesn't seem to come with the hardware required to mount to the QueenBee Pro, which has different extrusion end brackets than the...

I've spent the better part of 6 months printing, and reprinting many different iterations of drag-chains, or cable chains, for the Ender 3 Max. I think I came up with a pretty decent solution. I have removed my filament runout sensor, but this...

This is a highly anticipated 'Z' Axis Cable Chain for the Ender 3.\r\n\r\nIt's currently in development, as there's one obstacle to overcome - the wiring provided with this 3D printer is too short to be used with a cable chain. I must figure out how...

My Migbot never came with drag chains, so I ended up tired of all the loose cables that kept falling around everywhere due to my crashes. Those cables would always get stuck causing me to crash into the Y-Axis frame over and over again. Not to...

I remixed the SuperSniffles contribution Eva for the vCore Pro and mounted it on the the XY Joiner left from RatRig vCore3 https://contrib.eva-3d.page/cable_chain/xy_cable_chain_mod/ My poor CAD skills didn't allow me to make it printable without the...

I designed it for a 26mm wide cable chain, but will still work with anything smaller in width. It would still work with wider cable chains, but it would sit a bit further out. This just clips on the side where the body/frame and Z-gantries meet (40mm...

-----------------------------------English--------------------------------This is an adapter for attaching a drag chain (10x20mm) for the X-axis.One holder is attached to the Z-axis and the other to the X-Carriage. No holes have to be drilled or the...

I used his original design as the foundation and added a drag chain bracket to suit my requirements. The print quality is excellent when using 0.2mm layer height with light support. In addition, I created two cooling fan mounts inspired by the...

These Mounting Holders are specifically designed to securely attach the CK15 drag chains directly to the Shapeoko-X without requiring any drilling or modifications. ...To achieve this for a Shapeoko-X measuring 50x50cm, we utilized 27 components of CK15...

I tried printing the drag chain links from johnniewhiskey, but the links didn't move as freely as I wanted them to. I came across this remix from Yeggster and they worked much better. I needed them to fit on a 3/4" rail so I resized them. They are...

Drag Links and Clips should be printed at 100% infill. I printed at .2 layer height but .16 would probably be better I printed ends with 20% infill. I printed at .2 layer height Overall Z height is still limited to about 392mm with this...

Remix from this design https://cults3d.com/fr/mod%C3%A8le-3d/outil/ender-3-v2-satsana-bltouch-hotend-cable-chain-small-mountI printed it for my Ender 3 with a Satsana Fan Duct

... in a repair. Draft version, pending further refinement. Printer Settings: Printer Brand: Prusa Printer Model: Prusa Clone Rafting: Not Used Support Material: None Required Print Resolution: Set to 0.2 millimeters Infill Percentage: 35% Density

This cable chain ( spine ) supports the extruder ribbon cable on the Sovol SV06 3d printer and stops it from sagging on taller prints. There are three special pieces for the ends of the spine. Refer to the pictures for correct placement, orientation,...

However, we found that the original drag chain holder design is more minimalist and suits our needs better. We've also already mounted our extruder on top of the machine using the mount from Thingiverse: 2448418, designed by Alpharic. This simple...

This is a custom cable chain designed specifically for the Zonestar Z6 printer. I'm currently upgrading my Z6 to the latest model, Z6B, which features a heated bed upgrade. To accommodate this new feature, I've created both terminal links for the...

I needed to mount the drag chein on the "ceiling", so I added a parameter and did some adjustments.

Side holes are M3 at 13 centers.  Floor holes are M3 at 30 centers.The rows of slots are for cable tying the wires & tubes so they don’t slide within the Drag Chain.PhotosChain.  Shows the bend with 2 ends.  The black dots are...