3d printer cooling duct

This is just a TinkerCAD chop of ShaunTheBaa's part-cooling fan duct. Shaun's is perfectly functional as-is, but has a lot of wasted material obscuring the user's view of the nozzle. I just hacked the dead stuff off so I could see better. ...

Cut the printed duct to match your required length.

I obtained this design from a Cr10s Pro cooling fan and adapted it for use on a Sovol printer. ...To prevent warping, I recommend using either PETG or ABS filament.

... off bridging and change the solid layer angle to 90 degrees. Be sure to clean out any "spaghetti" in the air ways. The short fan-to-duct bolts are M3-10. (2 bolts, 2 nuts) The long duct-to-extruder bolts that replace the original ones are M3-60.

To address this challenge, I've added a cooling duct and rear fan mount, which ensures that the motor remains at room temperature or slightly above. The 40x40 mm fan should be oriented so that it pulls air out of the duct through the grilles on each...

For the exhaust duct, I'm using a hose that fits perfectly: https://www.amazon.com/gp/product/B001PQDUA0/ref=oh_aui_search_detailpage?ie=UTF8&psc=1. A zip tie or hose clamp securely attaches the duct; however, it may come loose if tugged. ... This...

... feel any air flowing backward like I did before. Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Resolution: .25 Infill: 10% Notes: 1 perimeter pass and 2 top and bottom solid layers. ...Walls are 1mm thick.

... a low-flow design with 1.5mm diameter duct nozzles. 2. The 9_ring_duct_2mm_holes.STL file has a low-flow design with 2mm diameter duct nozzles. 3. The 9_ring_duct_2mm_holes_high_flow.STL file boasts a high-flow ring with 2mm diameter duct nozzles.

... feel air flowing backwards like I did before. Print Settings: Printer Brand: SeeMeCNC Printer: Rostock MAX Rafts: No Supports: No Resolution: .25 Infill: 10% Notes: One perimeter pass and two top and bottom solid layers. ...Walls are 1mm thick.

This is a Remix of Ender Jet Cooling Duct, it also fits CR-10, 10S, S5, among others. I did a remix on these two because there was a gap, an opening between two walls. In the top half of the included picture (the 3 version is on left, the 4...

... and 15% fill without raft or support. Be cautious with bridging over ducts; try turning it off and changing the solid layer angle to 90 degrees. ...Don't forget to clear any "spaghetti" in airways and remove chrome fan guards (fan bolts are M3-10).

The fan duct installs effortlessly without stripping away the sleek Davinci Mini body cover. ...Simply detach the original duct and the metal plate situated beneath the extruder to make way for a smoother upgrade process.

Remix of BMG Areo Fan Duct for the Volcano hotend Mounted on Mellow Wind BMG type direct drive extruder

To start the fan duct process, simply duplicate the design and you'll be able to print two identical sides.

Print instructions After printing and getting rid of support materials, unscrew the screws on the front and bottom of the printhead(behind the heaterblock on the 45 degree angle part), then attach the duct to the printhead using the two screws you...

... fill without raft or support. To avoid bridging issues over ducts, disable bridging and adjust the solid layer angle to 90 degrees. Before printing, ensure all "spaghetti" is cleared from airways. Remove chrome fan guards. ...Fan bolts are M3-10.

I found the available fan-attachments for the RF100 take up to much space around the printhead, and also sometimes don't produce enough airflow. This cooling solution utilizes a radial fan design and can be attached to the printhead using already...

... in a plate that relies solely on M3 screws and no heat insert, I'd be happy to accommodate your request. This design should fit perfectly, but unfortunately, I haven't had the opportunity to test it yet due to the absence of my Hemera printer.

Hello dear Artillery Community I have found a solution for an unplaced fan, for which you don't have to rebuild half of the printer and still have a perfect view of the nozzle from the front. Cooling from both sides with the Upgrade!! It wortks...

This is a remix of Mathlad's duct, all I have done is make the duct 10mm bigger to direct the air at a lower nozzle. ... The interior has been rounded a bit too but I'm not sure of what effect if any this will have on air flow.

Own project. ...Duct for side fan. Very thin. Watch out for thin walls and support. I've used small magnet glued for holding fi8x2. ...If needed there is a place for additional fi4x2 (common used in USB plastic cases)

A custom-designed fan duct tailored specifically for E3D's 50mm x 15mm blower fans, allowing for seamless integration onto any E3D heat sink that offers sufficient clearance for the blowers.

This is a mounting bracket and 40mm fan ducts for an E3D type of hot end. Tap mounting holes with a M3 tap. I use PC carbon fiber filament but PLA, ABS, or similar filament can be used. ...

I'm building a fresh start on a brand new fan duct for my trusty Sovol SV01. ...The printing process is underway and I'll share the first images as soon as possible.

Pi-top laptop heatsink cooling with turbo fan improved performance 5%, due to cooling it was not freezing up. ...I have printed with Anet 8, stl file attached for your reference.

Plate Motor 2x 8mm M3Duct to Plate 2x M3 8mm Studs and 2x M3 8mm screwsFan to Duct 4x M2,5 6mmBLTouch 2x M3 6mm The offsets for the BLTouch Smart 3.1 are, from center of nozzle to front 42mm and to right 3.5mm, Z form nozzle to top 2mm Marlin...

Upgrade your device's cooling system by replacing the conventional 30x30 fan with a more powerful 40x40 fan to maintain optimal temperature.

Bottom modified for maximum print clearance.*\r\n\r\nMy PLA-printed part shows slight deformation in early layers without fan operation, but duct's function and clearance remain unaffected. ...A heat-resistant ABS version would be preferable to mitigate...

The purpose of this part is to distribute the air a little bit better than the stock duct is capable of. No additional parts are necessary however I recommend using a heat sheild between the hotend and this component. ... PLA+ 0.16MM Layer height ...

The user has replaced their factory-installed duct with one that disperses airflow on both sides. This modification appears to be performing significantly better than the original system. ...Future updates will include redesigning the nozzle to allow...