3d printed xbox controller

This is a remix of the Xbox one S controller mount. ...I made this to improve support on USB connector when charging or using with computer. The measures are 6mm x 10mm It fits perfect on my xbox one controller

Mounting solution tailored specifically for original Xbox One controllers, featuring a dual-screw design that securely attaches to most surfaces.

Simple XBox one Controller Wall Mount that Allows for Charging the battery and keeping the voice module attached.

Adaptation of https://www.thingiverse.com/thing:2188329 Single Xbox one controller wall mount with no headset hook.

This is a mount for the Xbox One S Controller to use under a desk or shelf.

This is a Stand for the Receiver of a Xbox 360 controller. ...It sets the Receiver upright to improve reception.

I've added a clamping mechanism to hold an Xbox controller onto the side of a desk

Xbox One Controller Wall Mount. A sleek remix of crazyg0od3's design, with only the contour line remaining intact. To make it easily printable even on budget-friendly 3D printers, several adjustments were made. Mine was printed on a Tronxy X1 with...

Update (2017-02-19): Added support for Xbox Controller Wired MKIII - a hole was added to the bottom to accommodate the screw holes. Added support for Razer Sabertooth MKIII - a hole was also added to the bottom to reach the screw holes. Or check...

... ...Can hold an Xbox One S controller, should hold other Xbox controllers but cannot verify this. This version is intended to be stuck to a flat surface with double sided tape or the like. ...Another version with holes for nails will be uploaded.

I modelled this to be visually similar to the official Microsoft Xbox Controller stand because I could not find any decent models anywhere (despite there being dozens of models for Xbox controller stands)... The fit, balance, and angle of this...

This 3D-printable model solves several issues with the original controller joysticks and can be installed using just a Torx-head screwdriver. The Smart Joysticks are adjustable, allowing users to switch between thumb-pieces of varying heights,...

This stand is made for 2 Xbox one controller. I've used PLA, but you can use a metarial you prefer. ...I made the logo after I printed the first, so that's why no logo on the printed one on the photos.

Remixed from https://www.thingiverse.com/thing:2788589 Created module for my Xbox 360 controllers which I mostly use on PC gaming. Print the Base and Cap from Original. NOTE: Make sure to add support in CURA and also enable bridge mode. ... Printed...

You can edit it online at https://www.tinkercad.com/things/f3wBbQM5tjh\nI created a custom Xbox controller mount using Tinkercad, specifically for the 360 model. Although it may not be perfect, the print time comes in under an hour. I recommend...

I made a replacement for my broken battery cover of my controller of xbox one s if u like it give me a like, and use it :) use the orientation at the printing as u seen on my second pic. ...print it with helper see pic 2 and 3

This stand is made for 2 Xbox one controller. I've used PLA, but you can use a metarial you prefer. ... I made the logo after I printed the first, so that's why no logo on the printed one on the photos.

Give style to your gamer space with this cool XBOX headset and controller stand, you can place all the controllers you want!

Here's my new controller, an Xbox One version featuring Batman's iconic logo - a bold and eye-catching design that sets it apart from other standard controllers.

A Holder for the Xbox Controller for the Skadis pegboard. ...The 2 Hooks slot into to 2 parallel holes on the Ikea Skadis and hold the controller securely.

Xbox one controller X buttonVersion 3 / 18-10-23This is a button to replace the original X button. (Xbox one controller)Made this because I ruined my X button and needed a new one. ...Tested on a PDP afterglow Xbox one controllerClicks just as well as...

In Fusion 360, I designed Controller support for Xbox in PLA, designed to be fixed on the xbox x series PLA PREMIUM WANHAO GREEN infil 20% It is recommended to place it on the corners. ...

High-quality designs call for sturdy wall mounts, like this custom fit one tailored specifically to an Xbox 360 game controller or the latest Xbox One version available at http://www.thingiverse.com/thing:668534

Design a custom Xbox stand that can hold two controllers securely and stylishly. ...The stand should be made of durable materials and have a sleek design that complements the Xbox console.

Here is a rewritten version of the original text: A custom holder for an Xbox 360 controller is designed using an original three-dimensional file in SLDPRT format. ...The object can be printed with supports, making direct contact with the bed as seen in...

This wall mount is designed for Xbox 360 controllers, securely fitting around the battery and featuring two 6mm screw holes. An accompanying bracket assists in attachment to a shelf, as displayed in the example image. ...Printed with black PLA on a...

Wall mount for a wired Xbox One controller. This uses Command strips to stick to the wall. This design allows space for the cable at the top, and the headphone jack at the bottom. ... No supports required if printed on its side.

A small print that allows to hang an xbox controller under or on the side of a desk. It only requires 2 additional screws or some glue to install it. ... To avoid use of supports, orient the object such that the back of it touches the plate of the...

An iPhone 4 case is available with an integrated Xbox controller design, made using the customizer tool on Thingiverse (http://www.thingiverse.com/apps/customizer/run?thing_id=58001). ...Users are encouraged to share pictures if they choose to print it.

Simple one piece IKEA pegboard accessory for your Xbox One / Switch controller. Use only one peg on the board.Print it on the side with support for the peg only (see picture).