3d printed wire stripping tool

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

All parts are printed, including hinge pins. I'm working on a smaller version that will use filiment rivets instead of pins. Currently, the hand crank is too small to turn the load so the center needs to be turned by hand. I plan to add a motor to...

You can set the X_MIN_POS to -1 and the Y_MIN_POS to -24 and the bed size to  234 on X and 211 on Y and then you won't run into issues with it trying to print off the edge of the build plate, you should also change them in the slicer to match. I...

The secondary goal was to keep it simple and quick to print.The tripod consists of the following components:Tripod Head: Featuring fixed holes positioned at 20 degrees from the central axis.Telescopic Legs: Made from 6mm outer diameter and 4mm inner...

The templates cut the rods a little short (3mm) so that there is room for any tolerance stackup in the X and Y axes.Some NotesAll of the parts (except for 1) are printable without supports I recommend 100% infill for the “Sand Cover” piece to...

--------------------------------------- The new Spool Winder: You will need: Print the winder parts: WinderHandle - need 1 WInderHub - need 1 WinderLeft - need 2 WinderRight - need 2 SpoolHolderBaseA - need 2 SpoolHolderBaseB - need 2 Hardware...

... for personal use only, non-commercial, not for resale! You cannot sell the digital model, a derivative or adaptation of the model, nor can you sell prints/builds of the model. ... Instagram: https://instagram.com/srheuropecom?utm_medium=copy_link

It should be fully rules complaint but check dimensions before using this design.Note: At time of upload, the design has not been tested in competition and has no guarantee of performance.Note: The pictures included with this design show a Launcher...

As for printing requirements, please note that some of the parts in the images do not match their .STL file counterparts due to an error on my part. I uploaded images that demonstrate how to obtain the correct pieces if you encounter any issues. All...

Installation ------------ Print out the four switch holders and slide them into the aluminium channel on the X and Y axis, as shown in the photos. The X axis holders are slightly longer than the Y axis holders. The tolerance is quite tight so they...

Tighten lightly, and you're good to go. Print instructionsCategory: Sport & Outdoors Summary Update 12 Oct 2019: The original design worked pretty well, but wasn't perfect. I redesigned it from scratch in Fusion 360. There are now three...

values_for_discrete_vars= { "x":[0,-118], "y":[0,-99,"b"] } possible_inputs_combinations=list(product(values_for_discrete_vars['x'], values_for_discrete_vars["y"])) def run_optimizer(input_value): result = minimize(objective,input_value) # Optimizer...

It has a thin bone structure, so I recommend printing it in a large size or on SLA/DLP. Ovis From Wikipedia, the free encyclopedia Jump to navigationJump to search This article is about the genus of wild sheep species. For the domestic animal,...

with a smaller diameter printer nozzle, it might be possible to print that wall thinner. Additionally, the FC file is really only recommended for worn out darts, or for a shellshock with an upgraded spring. ... Marked as WIP ~~for the FC files, but...

TRABAJO EN PROCESOCon este upgrade convertimos cualquier SIGMA a filamento de 1.75, usa extrusores Titan y Hotend V6 de E3D Original.Hemos respetado todos los componentes originales de la impresora, los ventiladores, el termistor y el cartucho...

I printed in PETG, Black, Orange, White. Orient the model on the flat surface in PrusaSlicer then paint supports on the lower edges of the camera shroud. Set supports for enforcers only.AssemblyThe Raspberry Pi 4 (I used a 4GB) and camera V2 are held...

You’ll need a large printer for the Converter to accommodate the handles but it was necessary to print in one for strength (peace of mind when a £500 drone hangs in the balance). The phone clamp requires an 80mm M6 threaded bolt (I buy threaded...

I wanted to have both a powerbank and a mobile lab power supply which are also protected by a corresponding housing, in this case the ammunition box, waterproof.I wish you a lot of fun and success in rebuilding...

It doesn't cost you anything extra, but helps me out a lot :) Both links in this post are affiliate links. Print instructionsCategory: Hobby Summary Update: I added a second version of the top part of this case, which has a cut-out for those who...

Make sure to print the models with minimal infill, - they do need to float after all. There are two main pieces in the kit which we add magnets to: the IgG (antibody) and the Ag (antigen) models and it is*really* important that we insert the magnets...

Screws come with EAF. 3X M6 hex nuts - two for EAF adapter and one for TP-Link adapter If you use a William Optics Dual-Sided 210mm or 245mm dovetail plate, use the following bolts: 2X M6x60 SHCS for riser 2X M6x20 SHCS for EAF adapter 1X M4x16 SHCS...

In the case you see a distinctive tilt into one or both sides of the build plate, first try to disable this feature and perform a test print. Tweak X_TILT_COMP and Y_TILT_COMP if needed to achieve an absolutely flat first layer printout. Use...

The alternative file is what is in some of my first renders and does look cool, but they are often annoying to print and glue on the vehicle so adding them is up to you. Size of model when completed 165mm length, 90mm width, 68mm high. ...Instructions...

 There are two versions of this stop: a simple one that indexes directly against the material, and one with a hole for a dowel that you can epoxy into place to create a spacer for cuts narrower than the width of the track.You'll want to print two...

All parts are printed with PLA plastic, everything fits on a standard 200x200 mm table, but it is advisable to use 220x220 - you need literally for a couple of parts to minimize support. Assembly video: 1)...

... soon. For those of you thinking about supporting us on Patreon, our patrons get special access to our entire back catalog, including the Meepleverse stuff (not to mention license options to sell printed versions of our designs). ... Happy holidays!

The main point is that the duel disk can now be printed from a single spool, depending on your settings. Then I added some extra features for quality of life. Features: - All slots (monster, spell/trap, graveyard, extra deck) support cards in...

Assembly video (in Russian): https://www.youtube.com/watch?v=rt2GikOnDV8 The parts are printed with PLA plastic, the body and struts are 100% infill, the wheel guard mounts are 75%, the wheels are 50%. When assembled, my copy weighs 1466 grams. ...

If your looking for the original look the v1.0 release at my Github repository: https://github.com/kellyegan/Arduino-Mounting-OpenSCAD-Library The library uses tbuser's pin library for the pin mounts: http://www.thingiverse.com/thing:10541 There are...

These models should be also shrank to 80% scale when printing.If "1min-holder-1.stl" is too thin, use "1min-holder-1-thicker.stl" instead.note : Since the number of optional files increase, it might be now confusing to add them here. So please...