3d printed wide body kit

------------------------------ PRECAUTION: Après quelques prints, il faudra contrôler que les tensions soit toujours bonnes. Procéder à un ajustement ci nécessaire. ----------------------------- Ce custom est un projet personnel, qui m'a pris...

* The final touch was designing and printing a small adapter for a power socket (similar to this one) I happened to have. * I drilled 5 small holes in the back of my tablet, fixed the power socket there using my adapter, and soldered the wires...

The equipment tray and servo lock **must be printed as one assembly**. I separated them so you easily could make servo lock for different servo (in that case I use 1181MG servo). I made the square on the equipment tray floor for you to easy pairing...

Once the bed has been measured, dropping the nozzle to print height will bring the nail back in range of the magnet and retract it to the stowed position. The M5 iron grub screw attracts the magnet back to center and also helps extend and strengthen...

**Gravitrax Ball wheel V1.5** - Difference in height 80mm - no support necessary - 2 pressure parts: wheel, pillar - Printing time approx. 5 hours - Select the STL file according to the length of the gearbox, 9.0mm or 12.5mm. - I recommend the...

I had problems with the walls printed vertically. As the plastic wires are laid one on top of the other, the wall is not very strong and it had the tendency with thermal shrinkage to crack. So I added different shaped ribs to see which ones are...

Using it I created 12v powered Media centre with LibreElec running KODI so that I could watch TV-shows or movies in my RV without having to bring disks with me or have access to streaming services. I load the HD up with my ripped DVD's and then just...

The main point is that the duel disk can now be printed from a single spool, depending on your settings. Then I added some extra features for quality of life. Features: - All slots (monster, spell/trap, graveyard, extra deck) support cards in...

Tools ==== * Soldering Iron * Allen Wrench (M3) * Super Glue * hacksaw or carpet knife Assembly ======== * Print the top, bottom, switch bracket and optional hemera bracket * Solder the two pin header to the back of the Duet3d PCB board * Fasten the...

There is, however, a fair amount of stuff to print for this modular insert and some optional parts. I will Identify the stuff below that is optional. To start, take everything out of the original base game box, including the manuals, player HP/RAD...

For the actual printed parts, this is designed for the tolerances I have experienced with hole shrinkage. It is intended to be relatively tight to the shaft so gently clean out the hole and push onto the shaft. It may take a couple of times to get...

There is a version (1c_p1.stl and 1c_p2.stl) that is cut for easyier printing on FDM Printers and a Version (1c.stl) that isnt cut. 2: Its Basically a hinge in Sector mechanicus Style that allows you to make ramps or drawbridges. It comes in 3...

There are also two variants of each model - one "basic" variant, and one variant that has been slightly altered to suit printing at 28mm scale. You will find all 28mm variants in the zip archive named "28mm versions" included in the purchase. All...

Planet's rings are stable thanks to the gravitational influence of the planet, and the presence of shepherd moons, like Prometheus and Pandora, that prevents the accretion of the disk material into a denser moon. Saturn is also known for having...

There is a new version of this carriage at https://www.thingiverse.com/thing:3615464 AND an even newer one at https://www.thingiverse.com/thing:3688067 ** ** I'd recommend that newest version instead for better rigidity and simpler printing and...

I printed the part using supports which are only necessary for the corners to the upright face. -- x -- I've also included a camera housing for the rear camera (plus fittings). It is intended that this will be attached to the upper plastic trim...

Note that the Base Plate was not countersunk in the model for ease of printing and to allow the user to choose the fastener style. Bill Of Materials: (1) Mount Rev0 (1) Base Plate Rev0 (1) Adapter Spacer Rev0 (1) Holder (4) M3x20 Steel...

Welcome to the home for the things to print for the Eff-Uno Racer project (https://github.com/oracle-devrel/eff-uno-racer). Eff-Uno Racer is a LEGO© Open Wheel Race Car that you can build and remotely control. Most of it is made with LEGO© bricks...

As for printing requirements, please note that some of the parts in the images do not match their .STL file counterparts due to an error on my part. I uploaded images that demonstrate how to obtain the correct pieces if you encounter any issues. All...

Tips Be sure your Z axis is positioned so that the endstop is above the level of the print bed before you begin the z probing procedure. You can also use the adjustment for raising the Z axis when probing to help. Finally, I welcome all feedback. It...

I wanted to print this awesome design by HexiBase on my Ender 3 but the two halves were too big to fit on the build plate so I split each one into two smaller sections. The two sections are joined together via a tongue and groove arrangement, making...

Instructions If you plan to print in ABS, scale the object up by one press of the up arrow or the case will be too tight. ... Using the following options: 5width = 58.6 5height = 7.6 iphone_version = 1 4_per radius = .3 pattern_rotation = 10 5cornerR...

Two versions available: > 1.3.1 Wheel + 2.2 Distance: Can be printed without support and must then be glued together > 1.3.2 Wheel: All in all, but needs support (for Overhang Angle 89 °) The axles are small and the rims fit exactly, so make sure...

This is my over complicated / over engineered solution to prevent humidity from ruining my filament while it prints in my garage. The spool sits on the rollers inside the container and feeds out a tube on the bottom. The roller assembly has an...

You may have to modify the parameter "d_cable" in the OpenSCAD source file and re-create the .stl file to match your cable: - Download and install OpenSCAD from openscad.org - Open the .scad file in OpenSCAD - Modify the value of the "d_cable"...

UNC 1/4 20 - http://ali.pub/4kpo3g I use high-speed epoxy to fix the screw and handle AB Glue Epoxy - http://ali.pub/4hvg7o The elastic that is yellow in the picture is a TPU filament - http://ali.pub/4kpplb I printed a knob from PLA filament -...

Cut in smart pieces for easy printing. Lyzz Kaboom - Goblin Lady (Fantasy Pin-Up)This crazy Goblin lady is passionated about explosives and traps. She recently assembled a huge amount of giant missiles with Zipzaap with the plan to launch a bunch of...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

I provide an easy-to-print alignment tool to ensure the heatsink is perfectly positioned for the cover to fit.\n* Direct airflow through the heatsink, don't leave proper airflow to chance.\n* Duct air in one side and out the opposite to maximize the...

I don't remember what size o-rings were used, but print the piston so that it just fits inside the 1-1/4 PVC tube and try different sizes until they make a decent seal. It doesn't need to be tight. I also sealed up three of the pass-through ports...