3d printed waveguide

Assume structure can move only rightwards from starting points at given array perimeter += (future_value - current_value) + (shape[1+i] == '1') print(perimeter) ``` Note: `0`s or non-matching nodes could be part of structure, though no code will...

**Please buy using the following links to support my creations (doesn't cost you anything):** [Good quality E3D V6 clone][1] [1]: https://s.click.aliexpress.com/e/_AqHeoo [Good quality E3D V6 clone copper version][2] [2]:...

You may have to modify the parameter "d_cable" in the OpenSCAD source file and re-create the .stl file to match your cable: - Download and install OpenSCAD from openscad.org - Open the .scad file in OpenSCAD - Modify the value of the "d_cable"...

- car fuse holder with adequate fuse - actualy not necessary as Dig-Uno can handle up to 10 Amps of current and is already fused, but I just never push the main power through the controler, can be skipped to simplify things Parts of this are...

I had problems with the walls printed vertically. As the plastic wires are laid one on top of the other, the wall is not very strong and it had the tendency with thermal shrinkage to crack. So I added different shaped ribs to see which ones are...

Always turn it off after use and keep an eye on the battery charge.One battery charge should yield 6-12h of usage (depending on resistors and IR LEDs)If you want to use your Wiimotes with the Dolphin emulator on PC, you still need to connect them via...

How to put it together?It consists of 6 pieces of printed and screwed parts (fig.):● screw any long M3 screw into the hole of the PIN part to create a thread in it andunscrew it again● insert the BRACKET (right hand under the (+) mark and left hand...

* The final touch was designing and printing a small adapter for a power socket (similar to this one) I happened to have. * I drilled 5 small holes in the back of my tablet, fixed the power socket there using my adapter, and soldered the wires...

You may have to warm the rear Pipe Sockets a bit as you put the 8mm Pipe in, but depending on your printer, it'll just fit "Snugly", whereas 7mm Pipe will be a touch loose until you tighten down your bolts/nuts.Seriously, use PLA+ (PLUS) filament...

Please ensure that this part will fit before printing. May require some tweaking. Results will vary.) ~4 In. flap ~Flap joint Optional parts: ~4 In. coupler Things you will need to purchase: ~4 In. duct fan...

UNC 1/4 20 - http://ali.pub/4kpo3g I use high-speed epoxy to fix the screw and handle AB Glue Epoxy - http://ali.pub/4hvg7o The elastic that is yellow in the picture is a TPU filament - http://ali.pub/4kpplb I printed a knob from PLA filament -...

There are two methods you can use, either print up a new modified WhiskerScar with the rib cut out for a 19 mm OD and 16mm ID 1.7 mm thickness o ring (or some close equivalent) or you can use electrical or masking tape on an existing Whisker scar...

For example, I always made the print bed side visible because I liked the surface better there. With this little Stepdown Modules you can connect the 12V fans to the 24V power supply. If you have installed these two Noctua you only have to remove the...

I printed a scan of the front of the hull and then glued it with dichloroethane. For cooling grates, I used modifier objects, as well as the author of the original project. I added mounting brackets and spacers to secure the power supply under...

Proceeds will be used to purchase printing filament so I can keep testing and designing cool new things that you might find useful. Thank you! Note: Have a look at my other designs, I have some nice sharpening accessories for all your knives...

The alternative file is what is in some of my first renders and does look cool, but they are often annoying to print and glue on the vehicle so adding them is up to you. Size of model when completed 165mm length, 90mm width, 68mm high. ...Instructions...

The LED-tube itself is printed from transparent plastic. Feel free to install a lipo and a step-up-converter or whatever you want ... There are three versions of the body, for - arnuino nano - node-esp8266 development boards - 49 x 26 mm -...

2) when everything are ready, and the housing was printed out. you can starting to connect the circuitry as per attached diagram. Please make sure the coinnection is correct before you put through the live electric supply. 3) I didn't reserved the...

Program it and what pc software to use to control it. Post-Printing Part List 1x Arduino Uno https://goo.gl/Ha2f1n or Nano https://goo.gl/YUGV6z 5x 9g servos https://goo.gl/J1YWQp 1x 5vdc 2A power supply https://goo.gl/56VuYa Jumper wires...

There is, however, a fair amount of stuff to print for this modular insert and some optional parts. I will Identify the stuff below that is optional. To start, take everything out of the original base game box, including the manuals, player HP/RAD...

If you'd like to buy a print of this with metal inserts in the drill holes, please check out my gunbroker page: https://www.gunbroker.com/item/858377600 This is version 1.2 of the C93 paddle release jig I previously released. This updated version...

The Therion Ifrit is a large model around 120mm tall.  He has been sculpted and posed to print as a single piece on a 5.5" build plate with his base separate.   Presupported files are included for each model in both STL format and LYS (Lychee...

The major innovation in coins the Byzantine’s made was to have the emperor face the front rather than print a profile. Most US coins would then adapt the side profile and bank notes adapt a front facing image, if not cocked to the side just slightly....

Using it I created 12v powered Media centre with LibreElec running KODI so that I could watch TV-shows or movies in my RV without having to bring disks with me or have access to streaming services. I load the HD up with my ripped DVD's and then just...

The filament used is all dark red PETG eSUN brand, printed at 245 ° with bed 80 °, 100% infill to avoid any deformation in the heat. The description is not detailed simply because it is not complicated as a project, certainly a bit of manual...

Again, check several times before you drill. Overview of some assembly steps and setup here: https://youtu.be/QQAKxDcRNgc Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No Supports: YesResolution: 200 Infill: 15% Filament: Mainly...

The drawer should now slide into place.• I guess you're all done unless you want to make more drawers :)Installing Drawers under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will...

... as it will go.  12. Check the quality of the Z surface by test printing. ... 

K40 Paint Rack I recently started painting sla printed miniatures. Soon a lot of 25mm paint flasks crowded my workspace. So I was in need of some paint rack. I searched thingiverse but found none that appeals to me and whose parts will fit in my K40...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...