3d printed water feature

English : Soon version 2 compatible linear rails (as well as wheel), and easier to print. Do not hesitate to like it encourages! After some research on different sites, apart from paid designs, printable cable management kits are rare. I...

No print support needed!This is an as-is project, will not improve it any further.It works great, cooling is better than stock, it's solidly attachedonly downside is limited visibility on the nozzle.This is a bit weird to setup due to the metal plate...

By any means you are now scared to do this operation, I highly suggest you ask someone with expertise to help you on your endeavors.You have been warned.Step 1: partsFirst you need Noctua nf-f12 for the psu and Noctua NF-A4x10 FLX 12v Version.you...

Plastic parts printed in PETG, layer 0.2mm, walls/top/bottom 1.2mm, infill 40%. With good part cooling supports are required only for the lower groove of the tool holders. Development log: 04/09/2023 Working sample 04/10/2029 "Head"...

Print at 0.4mm nozzle, 0.2mm layers, otherwise all design tolerances will be wrong. It is a good idea (maybe essential) to specify 0.4mm wide outer perimeters in your slicer. PLA works fine. Supports are required, but only because of one very...

blue lines or infill) should be ignored. Post-Printing Assembly Guide Tools needed:* ca 10 wooden toothpicks, 2mm diameter white glue. The one that dries in 5 minutes works best for me.</li> <li>adhesive tape to keep pieces in place, while the...

-AUTO TRANSLATE TO ENGLISH- After 3 years of using my mobile charger (huawei P30 PRO) the connector had started to break slightly (surely my cat biting it and dragging on the ground helped) so I decided to print a protector. The regular models were...

It only added a couple of minutes and grams to just go with a solid print. I renamed the other files for clarity. I'll add more info as things are tested and refined.</p><p>The parts list is as follows:</p><ul><li>1.5mm (1/16") silicone rubber in a...

Plus more being added please see table belowSorry Painted in lettering and not double colour printing, Found a very light soft grit sanding made using the fibre tipped acrylic paint pens easier to use.&nbsp;Taken from...

#Printing tips Parts are designed to favour interchangeability and symmetry between ENG1 and ENG2, so they are easier to replace. **STL files are oriented randomly, please adjust side facing the bed so you get the least amount of overhanging...

If you don't use your Western Digital MyPassport Pro all the time, but more like once or twice a year as a backup device for your camera, the battery might be damaged through constant drain of stand-by electronics. My last device died of this since...

The filament used is all dark red PETG eSUN brand, printed at 245 ° with bed 80 °, 100% infill to avoid any deformation in the heat. The description is not detailed simply because it is not complicated as a project, certainly a bit of manual...

We merely tighten the hard plastic filter mounting hub against the printed (hard) top rim of the porkchop's stem. This appears to be good enough for me, but you should test it and add a seal if necessary. A flat O-ring with an ID of 22 or 23mm...

There is, however, a fair amount of stuff to print for this modular insert and some optional parts. I will Identify the stuff below that is optional. To start, take everything out of the original base game box, including the manuals, player HP/RAD...

This is a ventilation system for an IKEA Lack enclosure.The top and bottom flanges have a “key” that will align the two halves so that the screw holes line up as well as the notch that can be used for servo and/or fan cable management if you wish to...

BOM:-Smart filament sensor BTT upgraded version-2x screw M3x10-7x M3 Heat Inserts Nut Heat (same in original )after print carefuly cut the X&nbsp;&nbsp;UPDATE: config:&nbsp;now add Gcode command for turn ON/OFF by: “SENSOR_ON” or “SENSOR_OFF”config...

I use resin to print it myself due to the higher precision. If you own a soldering iron you can also solder one of the poles of the motor to the case itself and straight connect it to the rca-connector like I did in the photos attached. (photos to...

####Broom stick section: First test the printing tolerances by assembling only the left, right and release part. Insert the clippart of the wheel section. You might have to grind/cut a little bit on the parts for a smooth fit. Push in the Insert...

Summary: This is a WIP (work in progress), so don't expect me to answer question about how to print things. If you need different file types let me know and I'll see what I can do. I'm just a hobbyist and I'm always learning. ...

I printed my own, but it may not be to your requirements depending on the board size you're using. Power: There should be roughly 129 LED's used in total. At 5V, that requires a good bit of current. I bought a 5V 6Amp PSU from Amazon for about...

I've printed a half-dozen of ‘em and they’re smooth as butter. The M10 coupler will screw into the Bowden tap nice and easy by hand.</p><h4><strong>Instructions&nbsp;</strong></h4><p>The pictures should be easy enough to follow but just in case here...

(I use 4 x 25mm M2 screws) For mountig my rx and vtx, i printed 1 x vtx_base.stl which fits onto the fc stack. For the rectangle standoffs you need 2 screws and 2 nuts to fix it. These standoffs are inteded to use at the left, right and rear side...

... soon. For those of you thinking about supporting us on Patreon, our patrons get special access to our entire back catalog, including the Meepleverse stuff (not to mention license options to sell printed versions of our designs). ... Happy holidays!

(STL included for the feet: print four of them in TPU for best handling of vibrations) * Low version, which does not require feet to lift the Ender 3 Pro. There is no slot for a fan however. Use at your own risk as my advice is to always use active...

... in Tinkercad. Some of the screen shots show artifacts on the models from the edits, but do not show up on the prints themselves.Also if anyone has a spare Ender 5 carriage plate, I would happily take it off your hands (message me with price).

It all sounds confusing and over complicated but I can assure you that once the pieces are printed most of the process is fairly straightforward and the other parts to be used can be sourced quite economically. Finally, I will recommend a minimum...

I haven't printed the version with the hole for the reset button, I can reach in the USB hole with a spudger and poke the button so its not essential for my current project. https://www.tinkercad.com/things/hP2VRmHu4Q0 When I get round to making the...

How to put it together?It consists of 6 pieces of printed and screwed parts (fig.):● screw any long M3 screw into the hole of the PIN part to create a thread in it andunscrew it again● insert the BRACKET (right hand under the (+) mark and left hand...

I print it with the cut in the bumper, which you can separate carefully with an exacto. Then wrap the bumper around, and trim the plugs as needed until it fits together well. Then I use my soldering iron (set around 3/medium) to heat up the edges...

Please ensure that this part will fit before printing. May require some tweaking. Results will vary.) ~4 In. flap ~Flap joint Optional parts: ~4 In. coupler Things you will need to purchase: ~4 In. duct fan...