3d printed velociraptor resonating chamber

A constant current driver operating from 6 V to 15 V should do nicely for powering it directly from the main battery and adding an RC switch to control the light by the transmitter.\r\n\r\nI printed the chassis without supports using PETG and lots of...

My work shop is embarrassingly messy at the moment but I have tested them and they seem to work as intended. Print instructionsThe parts were designed to not need supports you will need to use a knife, razer blade and/or deburring tool to cut out the...

You can automate it by printing this gearbox that will snap into the mechnisim.I have been successful at driving it with plastic 9g servos after modifying it to be 360. I highly recommand using metal gears which I plan on doing as I already had lost...

NOTE3: If you decided to print all of these parts with some others you made yourself, don't come crying to me if nothing fits. This design is not complete and not tested at all. NOTE4: (This is for the future) This design is designed to work with...

Well I am just to lazy to print twice ;-), of course you can arrange all the “Text plates” and all the “cableTie” parts on a separate buildplate and go from there, that is your choice.Important; for the “Cabletie” Parts, due to sometimes small...

You’ll need a large printer for the Converter to accommodate the handles but it was necessary to print in one for strength (peace of mind when a £500 drone hangs in the balance). The phone clamp requires an 80mm M6 threaded bolt (I buy threaded...

The built-in socket has the advantage that no cables can be seen. Tools you will need: (see the pictures) Hot glue, super glue, soldering iron, screwdriver, ... Print instructionsCOMPONENTS: Attiny85...

Print at 0.4mm nozzle, 0.2mm layers, otherwise all design tolerances will be wrong. It is a good idea (maybe essential) to specify 0.4mm wide outer perimeters in your slicer. PLA works fine. Supports are required, but only because of one very...

Using it I created 12v powered Media centre with LibreElec running KODI so that I could watch TV-shows or movies in my RV without having to bring disks with me or have access to streaming services. I load the HD up with my ripped DVD's and then just...

------------------------------ PRECAUTION: Après quelques prints, il faudra contrôler que les tensions soit toujours bonnes. Procéder à un ajustement ci nécessaire. ----------------------------- Ce custom est un projet personnel, qui m'a pris...

I tested it by holding the thermistor onto the print-bed as it warmed up to 80c and I could see the fan getting faster and faster - but it was still really quiet. Even at the lowest (and quietest) default speed it puts out a good amount of air and as...

Assume structure can move only rightwards from starting points at given array perimeter += (future_value - current_value) + (shape[1+i] == '1') print(perimeter) ``` Note: `0`s or non-matching nodes could be part of structure, though no code will...

So, measure twice and print once. In my case, I cured this by simply enlarging the holes with a needle file. But when I came to do this design, I had no idea where the original holes would have been.\r\n\r\nThe rear of the case has positions for two...

Welcome to the home for the things to print for the Eff-Uno Racer project (https://github.com/oracle-devrel/eff-uno-racer). Eff-Uno Racer is a LEGO© Open Wheel Race Car that you can build and remotely control. Most of it is made with LEGO© bricks...

So I like to print a test piece before committing to anything big or sensitive. I find that making a piece of OS-Railway track using whatever filament is intended for the project is usually enough to warm up the bed and predict if the printer can be...

(Q-tips) Lubricate the sides of the piston with Shimano mineral oil (the same stuff that goes in the brakes) Push the piston back into the caliper. Repeat with the other piston. Park tool has this video available which explains the process without...

Remove the short piece of filament, reinsert the bowden tube into the coupler and print without the worry of irregular flow. #Other side effects: From time to time your bowden tube in the hotend will perish due to heat and need replacement. ...

Plus more being added please see table belowSorry Painted in lettering and not double colour printing, Found a very light soft grit sanding made using the fibre tipped acrylic paint pens easier to use. Taken from...

You may have to warm the rear Pipe Sockets a bit as you put the 8mm Pipe in, but depending on your printer, it'll just fit "Snugly", whereas 7mm Pipe will be a touch loose until you tighten down your bolts/nuts.Seriously, use PLA+ (PLUS) filament...

Print all the parts before assembling anything. 4. Start by assembling all the windows, doors, and trim as shown in image 1. 5. Assemble the motor mounts by gluing the two halves together. Ensure you align the holes before gluing. 6. Attach them...

... professionally done and designed to remove beautifully (provided you have dialled in your printer settings). They are guaranteed to give you one of the best printing experiences you've ever had! Are we allowed to use the term "printgasm"?! ...:-)

Summary: This is a WIP (work in progress), so don't expect me to answer question about how to print things. If you need different file types let me know and I'll see what I can do. I'm just a hobbyist and I'm always learning. ...

The drawer should now slide into place.• I guess you're all done unless you want to make more drawers :)Installing Drawers under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will...

So I created and printed some using CAD. I screw all the holes in the MGN 7. It is required for the MGN 7 M2 screws. If you get a longer rail you can use the other belt tensioner in the mod. This is stable enough. The assembly ... Then the...

These go in the 3mm perspex (or printed panels) (key spots marked in yellow). 24-42 x 10mm M3 countersunk screws. 5 x 10x5x4 bearings (easily available in hobby/printer shops). 10 x M6-PC4 bowden connectors. 12 x M5 nuts and bolts to mount to the...

Again, check several times before you drill. Overview of some assembly steps and setup here: https://youtu.be/QQAKxDcRNgc Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No Supports: YesResolution: 200 Infill: 15% Filament: Mainly...

Also, the "spikes" on the gripper didn't print well and had layer separation. The gripper is the part that connects onto the end core which pulls out. It uses a screw to tighten it. There are 2 gripper versions based on if you have the normal...

Shoulders and Forearms(https://www.aguilarworkshop.com/product-page/odst-battle-armor-arms)Armored Plate Carrier(https://www.aguilarworkshop.com/product-page/odst-battle-armor-armored-plate-carrier)Utility...

This is a thing I call the Sand Raker, it is a very peaceful print when finished and put together. https://www.youtube.com/shorts/fRqaw5RR5FI A kinetic sand piece that rotates via an electric motor with a pinion gear of 11mm, and rakes the...

Let's collectively push the envelope of what's possible with Raspberry Pi.Download, print, and commence your journey with Poisonberry Pi - where the capabilities of your Raspberry Pi 5 are just the beginning.Exciting Update for Enhanced...