3d printed universal joint

Tube (material doesn't matter, i chose stainless to match the optics of the bowl) some kind of epoxy glue assembly: after printing the required parts and buying the hardware you can start by assembling the scissor mechanism with the countersunk bolts...

Before you start, if you are planning on printing it first and installing it after, make sure you have installed the mount bracket for the stepper motor/extruder. The mount bracket is made to use the mount screws for the two upper rollers. If you...

Every part is designed to be printed without supports. All the electronics and extras I used are listed below. I had to scale the parts up by 2540% in the slicer. 2x Boss 4" Speaker Driver - ...

Once the case has been printed, the headphone socket can be screwed into place, and perhaps a tiny dab of super glue to hold it tight. The same can be done on the side of the ultrasonic Mic - a tiny drop of super glue before pushing it into...

I printed the original design and carved and drilled and glued until I got something that would work for me but it lacked elegance – actually it was downright ugly. The original design looks like it was done in Design Spark Mechanical and that...

... If you want to create a stand for your transmitter, print two "X10S_stand.STL" parts and attach them with a standoff. I've also included a JR module bay cover, remixed from https://www.thingiverse.com/thing:513861, which has space for angled pins.

Files with FDM are modified to print better with filament printers Set 04 - Generals and Staff - FM Bluecher in several poses, plus a few generals and other staff officers Set 05 - Misc. Officers - Many Reserve and Landwehr officers wore regulation...

You only need to print one lid for an entire stack. The idea is that you simply pull out the component boxes, unstack and remove the lids and the components are ready to go, in bowls, so your components are neat on the table. The magnets are placed...

2.6mm thickness - I used something like these:...

Originally published here: Mars 1962 reconstruction scaled one in sixty million by tato_713 - ThingiverseThis is a recreation of what the scientists though it was Mars before the first missions arrived to it, the Mariners. The model was made using...

Insane!Assembly: Print all the parts of the Zorbiter, but swap out the extruder body and motor cover for my 2 parts. Follow the assembly instructions for the Zorbiter almost entirely. You need to use M3 heatset inserts wherever a nut would...

Cyl Pin Diameter Bottom = (0.5,1.0,1.0) Cylin Separation = (3.81,3.00,0) Layer Thickness Value = (0.30,0.29,0.28,0.27,0.26,0.25) Key Blade Width = ((Five Cylinder Key Blade Layers*Layer Thickness), 7*Layer Thickness,0) Print Layer Thickness = 1 Back...

The base is made of 295x200x10mm MDF and is currently being printed with the other parts. This design can handle items as large as 50mm square, and the vice shown in the picture measures 4545 x 250mm. To complete the saw, you will need to source...

It is very easy to assemble and if you print an array of this devices you can have a grid for domestic use or outdoors activity like in a camping etc. This wind turbine device is a part of a further open turbo-machine system based in a pending...

You’ll need to print the following and its best to fit in this order: If running the V6/Dragon carriage mod then fit the cable retainer and cable into it first, skip this step if you’re not. I’ve included a few options you could use: Cable...

After clicking print, you'll be prompted to open the new tab and save the image or discard it, whichever you prefer. In order to proceed further, select each individual render starting from the deepest (-3900) layer all the way up until (-2900),...

It is parametric and you can change the angle that is printed within Solidworks by going to the equations section and telling it how tall is your frame (370mm) and how far out will the all thread touch the wood (mine is 200mm). From that the equation...

The printed version doesn't grip the shaft on which the thumbstick was mounted as well as the original part and may slide a little over time. If you follow this design exactly then you have 2-3mm to spare. ## Installation instruction (crude) ...

This brings me to this new part – it's essentially a clone of a design by Mangtronix http://www.thingiverse.com/thing:280974, but after printing his part I realized it wasn't long enough for the Wanhao Duplicator i3 (I didn't realize at the time...

Printing without support is required for this fan duct. Secure the fan with 2 M3 x 10mm screws and attach the duct to the carriage using 2 M3 x 25mm screws, with nut traps built-in for additional tightness. All measurements are in mm. #Response...

Now have fun printing and installing the brackets. A little tip: Use heatsinks with thermally conductive adhesive and not with the adhesive pads. These are no good. If you like my design please show it with a like or a make here on Thingiverse. ...

If the printed parts don't want to sit flush, sand/file the lower one's small end. Realign motor pulley and tension. The idler location is a little bit higher (on purpose) to more closely match the carriage attachment point. For the Y one near the...

So that fits best.DO NOT PRINT IN PLA! PLA can't withstand the summer heat.</p><p>&nbsp;</p><p>#############################################</p><p>Ich mochte den originalen Becherhalter für meine E-Klasse nicht, also habe ich mir einen eigenen...

My vision was for a device that: - Utilizes a 6x6 printing bed - Employs hard tac-switches over rubbery elastomers - Has a vertical layout reminiscent of classic GameBoys - Is simple to assemble and modify - Runs on the Raspberry Pi 2, unlike older...

In using the shroud while printing a model that takes up the entire bed, I found that the wires from the extruder need to be routed over the output end of the fan using wire ties, as shown in the new picture above. As I'm using a low-velocity fan,...

Desktop Waveshare 7HP-CAPQLED display enclosure with RPi Zero 2 W mount insideNeeds 8x 8mm M3 screws.Fits these cables/adapters:Vention Reversible 90° micro USB cableWaveshare Right-angle HDMI Plug AdapterWaveshare Straight Mini HDMI Plug...

When printing this jig, the only supports needed are below the two alignment fingers. When you import this part into your slicer software, it will likely need to be rotated to lay flay on your build surface. 1/2" PVC - Metric Drill Bit [1/2"...

Hollow clock : Highly visible with minimum occlusionEasy to operate : super easy time adjustment, minute and hour can be set separatelyInstant design change : clock face (index plate) is interchangeable instantlyEasy to print : printable without...

The entire box is designed such that if you print with 6 shells in your setting the outside walls will be solid, and the front wall will be double thick as it will take most of the hits. The bottom is flat, but has a large recess to allow you...

One without Sling, (a selflocking design), but i redesigned it, because of the tolerances, while printing, the teeth are not as practical as I hoped. -GT2_Clamp_Ender_5_Y_Carriage_without-Sling_v2.stl (not recommended) So i created one, with a kind...