3d printed traxxas slash parts

Mount for the Hobbywing Max10 SCT within a Traxxas Rally/Slash with a LCG chassis. There's a cutout for the temp sensor as well as it's pretty close. You'll need one M3x8mm and M3x12mm for mounting. The ESC and switch should friction mount though...

Front 25 degree caster blocks for a variety of Traxxas 2WD vehicles (Rustler, Stampede, Slash, Bandit) with the bearing in hub design. The stock caster blocks on these vehicles have no angle, and therefore match the chassis kickup angle of 30...

This custom part generates substantial downforce at speeds above 45mph, ensuring your car stays firmly grounded during the fastest runs. I rigorously tested it to withstand hard impacts. This attachment point is located on the bulkhead where the...

I've used Tiny P 3D printed wheels and found there's excess space on the front wheel after tightening, so I created a spacer to solve the issue. ...Instead of disassembling the suspension and damaging it with glue or wood dowels, I removed the existing...

3D Printing Device

EDITING SPEEDYBEE MASTER 5 HD - ALL 3D PRINTED PARTS

To ensure a seamless integration with the frame of the slash, apply gentle heat to the bottom using a heat gun as you tighten the screws. Printing the mount with its back facing downwards on the bed yields the strongest bond I've discovered so far in...

I knew that I would eventually flip the car and break something, so I decided to make the Flag Rods the weak link of the system, basically acting as a sacrificial part to prevent damage to the main component. You'll need 2 flags (any type will do),...

ESC plate for LCG slash 2wd to mount max 10 esc and power button

This is a 40mm x 40mm flat plate used to mount anything to the front area of a slash 4x4 LCG chassis. The plate is 4mm thick and can be mounted to the chassis with 2 M3 x 6mm button head screws (TRA 2575). I am using the plate to hold a GNSS...

... length for the bandit/stampede, and make sure to remix it too. Print Settings Printer Brand: Prusa Printer: i3 MK3Rafts: No Supports: YesResolution: 0.2mm Infill: 25-100%, 4 to 6 perimeters Filament: Any PLA, PETG, Nylon Category: R/C Vehicles

The 3D printed parts needed to convert a Macintosh classic II case into a Windows PC.

... have got you covered. Plus, they come in two convenient types: left and right wheels, ensuring a perfect fit every time. With a quick print time of under 2 hours, you can get back to the fun stuff – racing your mini Slash vxl through the dirt!

Print enthusiasts are recommended to use this enhanced version, and we suggest utilizing supports during the printing process for optimal results. Meanwhile, the 1/10 scale model has undergone a slight adjustment, now featuring a 17mm hex nut. For...

STL Files for 3d Printed parts for use on my small RC planes (MTOW<2 kg)

Custom made industrial/steampunk lamp with 3D printed parts, step by step tutorial here: https://bit.ly/3d2Y2Lq

Custom made industrial/steampunk lamp with 3D printed parts, step by step tutorial here: https://bit.ly/3d2Y2Lq

3D Printed Parts designed to use with Dave_C 4 Inch Micro Long Range Quadcopter. Print with TPU. ...Naked GoPro Generic Mount Base uses M5 bolt and nut

... For the correct print orientation check the file: "Infento_Waterscrew_3D_printed_parts.stl" If you want to print all the parts for the Talent Kit, visit this page: https://www.thingiverse.com/thing:5359204 Visit this website to buy the Talent kit.

... For the correct print orientation check the file: "Infento_Balance_3D_printed_parts.stl" If you want to print all the parts for the Talent Kit, visit this page: https://www.thingiverse.com/thing:5359204 Visit this website to buy the Talent kit.

... Print Settings: Printer: CTC 3D Printer Rafts: No Supports: No Resolution: 0.15 Infill: 40% Notes: The print quality turned out to be exceptionally high, but due to the weight of the rifle this mount will hold, I printed it with only a 40% infill.

If you print separate parts, consider checking for the correct print orientation: "Infento Talent kit all 3D parts.stl" ---------------------------------------------------------------------------------------------------------------- If you want just...

Steampunk/industrial lamp project with 3D printed parts (gear quarters and lamp shade). ...I wrote step by step tutorial and explained everything, you can read it here and also download those parts in more files/formats: https://bit.ly/3Ignag2

... 3x. For the correct print orientation check the file: "Infento_Crane_3D_printed_parts.stl" If you want to print all the parts for the Talent Kit, visit this page: https://www.thingiverse.com/thing:5359204 Visit this website to buy the Talent kit.

I created these 0-degree A-Arms to reduce the terrible oversteer caused by the stock 30-degree bulkhead on the Traxxas Rustler 2WD, with speedruns in mind. ... You will need: - Adjustable steering and camber links (VXL models should have this...

Materials: * 15x15mm wood: + 500mm x 5 pieces + 300mm x 4 pieces + 215mm x 2 pieces + 120mm x 2 pieces * 3D printed parts: + 3-way connectors, 4 pieces + 2-way connectors, 2 pieces + ATX power supply mounting brackets, 2 pieces (one for each PSU) *...

Crafted with precision using advanced 3D modeling software, this unique creation showcases cutting-edge design capabilities.

Crafted with precision, brought to life using cutting-edge 3D modeling techniques.

I recently raced in my first organized oval race and quickly realized that my HCG chassis Slash doe not handle well enough to be competitive in any way. I'm not out there for anything more than to have fun, but when I keep rolling over in the...

Micro BarTop Printed Parts