3d printed traffic light

On my desk was a sample of TPU filament (I had never got around to printing with it) and playing with the filament I thought: "if I can attach this to the model"... After repeated attempts to come up with a clamping system, I soon found out that the...

**Gravitrax Ball wheel V1.5** - Difference in height 80mm - no support necessary - 2 pressure parts: wheel, pillar - Printing time approx. 5 hours - Select the STL file according to the length of the gearbox, 9.0mm or 12.5mm. - I recommend the...

• build_plate_manual_y = The vertical position along either axis at which you intend for your item to be printed and produced. This could potentially refer to multiple settings and can help you organize production based on placement specifics of a...

My work shop is embarrassingly messy at the moment but I have tested them and they seem to work as intended. Print instructionsThe parts were designed to not need supports you will need to use a knife, razer blade and/or deburring tool to cut out the...

Parts are not oriented for printing. The STEP file is included for easy remixing. I am not an electronics expert but I did the best I could with the design, but still make this at your own risk and let me know if you see something that can be...

I wanted to have both a powerbank and a mobile lab power supply which are also protected by a corresponding housing, in this case the ammunition box, waterproof.I wish you a lot of fun and success in rebuilding...

---------- PRECAUTION: Après quelques prints, il faudra contrôler que les tensions soit toujours bonnes. Procéder à un ajustement ci nécessaire. ---------- Ce custom est un projet personnel, qui m'a pris beaucoup de temps à concevoir et à...

... as it will go.  12. Check the quality of the Z surface by test printing. ... 

This design fits on a Prusa i3 MK3 bed.Note: Please only attempt this if you already have some experience with soldering, wiring and electronics in general.Note: Some ATX PSU's may be too deep for this design so if your PSU is over 135mm deep it may...

Printing Tips: 30% infill at 50 mm/s If you wish to design your own fraction piece, you’ll need to know the size of a whole. One whole piece is 50mm tall with a diameter of 50mm and an inner diameter of 12.5mm. ...With those measurements, you should be...

I provided an easy-to-print alignment tool to ensure the heatsink is properly positioned for the cover to fit.\r\n* Duct airflow through the heatsink, don't rely on proper airflow by chance.\r\n* Duct air in one side and out the opposite to maximize...

This is due to the different number of teeth in the printed gears for each axis. Feed rate changes the speed of the motors. Be careful to not move the azimuth axis too far so the stepper motor wire connected to the motor for the altitude axis...

I printed it with ABS plastic, but PLA or other materials should work fine as well. To ensure it is strong and not prone to breaking easily on my first prototype, I used 50% infill (and four-layer walls) and might use less if I build another one. I...

Remove the short piece of filament, reinsert the bowden tube into the coupler and print without the worry of irregular flow. #Other side effects: From time to time your bowden tube in the hotend will perish due to heat and need replacement. ...

==================================================================== Easy to print, assemble, mount/unmount. To assemble with Nema14 motor you will need: ----------------------------------- * A set of parts from BMG or clone (gears, bearings,...

----------------------------------- What you will need: * Four of the Corner Posts printed in your choice of plastic. * Two strips of polycarbonate strip 1/8" thick, 4" wide, 2 feet long. (Available from McMaster Carr in the USA part number...

Megacity Desert Habitat building for tabletop, expanded by rectangular build option.It contains:WallsRoof tiles with the capssome special sized doorssome basic bits for decorationYou may need to mirror the corner pieces in your slicer to get all...

How to put it together?It consists of 6 pieces of printed and screwed parts (fig.):● screw any long M3 screw into the hole of the PIN part to create a thread in it andunscrew it again● insert the BRACKET (right hand under the (+) mark and left hand...

The drawer should now slide into place.• I guess you're all done unless you want to make more drawers :)Installing Drawers under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will...

I don't remember what size o-rings were used, but print the piston so that it just fits inside the 1-1/4 PVC tube and try different sizes until they make a decent seal. It doesn't need to be tight. I also sealed up three of the pass-through ports...

Well I am just to lazy to print twice ;-), of course you can arrange all the “Text plates” and all the “cableTie” parts on a separate buildplate and go from there, that is your choice.Important; for the “Cabletie” Parts, due to sometimes small...

The secondary goal was to keep it simple and quick to print.The tripod consists of the following components:Tripod Head: Featuring fixed holes positioned at 20 degrees from the central axis.Telescopic Legs: Made from 6mm outer diameter and 4mm inner...

The mounting holes are identical between that and the Creality 4.2.7 silent board, which is what I have installed in the first 'final' print. The stock 4010 fan fits upright screwlessly in a mount that holds it to the side of the case, and a buck...

Shoulders and Forearms(https://www.aguilarworkshop.com/product-page/odst-battle-armor-arms)Armored Plate Carrier(https://www.aguilarworkshop.com/product-page/odst-battle-armor-armored-plate-carrier)Utility...

I print it with the cut in the bumper, which you can separate carefully with an exacto. Then wrap the bumper around, and trim the plugs as needed until it fits together well. Then I use my soldering iron (set around 3/medium) to heat up the edges...

I need my printer to be able to use stronger higher temp materials and be able to print delicate single perimeter components for the wings and fuselage. I decided a direct drive upgrade would be a good upgrade to provide better performance and higher...

von LarkysPrintshttps://www.thingiverse.com/thing:2843853Meine Anpassungen beruhen allerdings auf dem Remix von emancarrillohttps://www.thingiverse.com/thing:3713857Die Idee des Griffstücks stammt von...

The "printmode = true" with its following variables will prepare a print-ready layout of your parametered Structures. The length of each (not printable) Threaded-Rod will be "echoed" in the OpenSCAD-Console. They can be cut to exact that length. -...

Two versions available: > 1.3.1 Wheel + 2.2 Distance: Can be printed without support and must then be glued together > 1.3.2 Wheel: All in all, but needs support (for Overhang Angle 89 °) The axles are small and the rims fit exactly, so make sure...

40x55mm.you need 2 pieces of rubber band, wire or tape.you need 1 piece of Periscope tube 01 or standard 32mm PVC tube.(Periscope tube 01 89mm long results in a Periscope in/out of 150mm)But you can also use standard 32mm PVC pipe to get a larger...