3d printed toothpaste roller

Here is a bird's eye view from the top:A single pulley gets attached to the left wall bracket of your curtain rod. The left clamp gets attached to the first tab of your left side curtain. The right clamp gets attached to the first tab of...

... Use a straight piece of wire or a drill to poke through the holes after printing. 2. Cut three pieces of paperclip wire, each about 15mm long. Bend one of them 5mm from the tip as shown in the picture. 3. Stick the bent piece through the knob axis.

What with trying to design mods for my printer, I figured having a virtual model would be super handy - and it got totally out of control!\r\nAs I've seen people complaining about not being able to get plans for the acrylic parts in case they break,...

I printed mine at a speed of 50, with a resolution of 0.2 mm. Assembly instructions below, assembly photo above. As always, any questions, don't hesitate to ask.Assembly:See numbered photo for reference.During assembly you'll want to keep an eye on...

In addition to printed parts, you'll need: * **16x** M3x10mm or less screws for MKS board, mosfets, and top cover (4x for each) * **1x** 80mm or 120mm fan if you want active cooling (strongly recommended) * **4x** M3x8mm or less screws for RAMPS if...

My huge thanks to both of them. Print Settings Printer Brand: MakerBot Printer: MakerBot Replicator 2**Rafts:** Yes Supports: Yes**Resolution:** 0.2 mm Infill: 20% **Filament:** [ Makerbot PLA...

Print DACSTOP.stl x 2 - use double sided tape under it and between it and the DAC...use the second and crazy glue it behind it so it won't move.... use velcro under the powersupply and use velcro on the case bottom so you can remove the power...

[0] Thing Title : Personalized Soda Can Holder v2 [0] Thing URL : http://www.thingiverse.com/thing:6591 [0] Thing Author : JadeKnight [0] Thing Licence : Creative Commons - Attribution - Non-Commercial - Share Alike [1] Thing Title : Spider mount for...

Soooo, I bought a new Taranis X7, tore it apart, printed a new shell, and I can now present the Taranis Pistola! This allows for up to 8 normal channels of control, plus you can link receivers together to get 32. You also get all the flexibility of...

It prints quickly, uses only about 1 gram of filament (0.33 metres of 1.75 mm filament), and is very easy to use.It clips onto the spool of any brand of filament, so it's a universal clip. It can clip onto 1.75 mm filament or 2.85 mm filament, so...

I have modified this with an easier to print screw ring with nubs for easy grasping and have uploaded 2 versions of the screw ring and insert one is scaled down to 99% so if the full size one is too tight the scaled down version should fit easier. I...

I had to print that after a craftsman tried to shorten the doors length in a rather barbarian style. The door is 83 cm in width - armed with an Ender 3 this translates to 4 parts with 205mm length each, leaving 1 cm uncovered as the door is so...

The 'heatmap' image I'm showing is just one I did a print screen from the internet - the quality isn't great, and I'm not sure of the size since I don't use topographical mapping myself. The probe points may not match the exact locations on the bed,...

This set includes all the printed parts which go along the metal plate (source form e.g. <a...

Printing without support is required for this fan duct. Secure the fan with 2 M3 x 10mm screws and attach the duct to the carriage using 2 M3 x 25mm screws, with nut traps built-in for additional tightness. All measurements are in mm. #Response...

POST-PRINTING There's room to mount a Micro-USB breakout board (see pictures) if you'd like to supply power on the side rather than out the back. These boards can be found here: https://www.amazon.com/gp/product/B0183KF7TM The BoB is mounted to the...

The V3.1 box has been on the printer for around 150 hours of printing with no evidence of overheating of the TMC drivers or the Raspberry Pi. I had to ramp up the ref voltage for the 4988 extruder driver from 0.72 to 0.85 to alleviate some skipping...

... I should now be ready for action. Printer Settings Printer: Velleman Vertex Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 mm Infill: 30% Notes: If you orient the meshes properly, supports are only needed when printing the Lower harness arm.

These prints require very little support if oriented properly with the rectangular sides face down - but you'll need good bed leveling and a smooth bed to get a good outside surface. There is support necessary around the SD card slot and HDMI ports....

Do not glue the skewers into the holes; even if the printed part literally just falls off the skewer, winding the thread onto it will keep it all securely together. ...Not gluing the skewers in will also let you remove the skein label and reuse the...

If it interests you, the design can be modified: https://www.tinkercad.com/things/8xbdOSIT0zA-makita-eleksmaker-mount The files include: - The face plate holds the router clamp - The mount block (lose or solid) connects the face plate with z-axis...

It is the low-poly and easy to print version of ionic, doric and corinthian columns. Doric and corinthian columns are supportless, only ionic column has some easy to clean supports. Just like chess knight is not photorealistic and just symbolic, goal...

The attachment itself is designed as a two-part unit for easier printing without supports, with the lower part serving for connecting the battery (it is possible to choose a version for Makita or Parkside batteries) and the upper part forming the...

I would not fly this rocket on an A motor for obvious reasons. I recommend the following print settings:Nose cone - 4 perimeters and 5% infill. Rockets are more stable in flight with more weight higher up. Tail assembly - 2 or 3 perimeters and 5%...

Print the required parts (some will need supports), glue the splash guard to the top of the airlift pump as pictured, cut the mesh to size and glue through it with the mesh retainer holding it in place on the holding basket's window (superglue was...

... Carl XVI Gustaf of Sweden presented Pink Floyd with the Polar Music Prize for their contribution to modern music. Thanks for checking in on us and for your ongoing support.CR8ED Out Of Hand Sculptor - Sandy Campbell3D Scanning and Printing - CR83D

Because there are no symbols in the other three statues it is difficult to identify them, and their names are indeed a vexata quaestio; according to Raffaello Borghini (1584), what they were actually called depended entirely on the oral tradition...

The new firmware includes aggressive temperature management to reduce overheating, thus minimizing print failures due to excessive temperature levels. Settings for fans and Z-axis probes: My updated 3-point triangular probing is now default with...

I strongly recommend printing Mpooh's fuse holder and wiring in an automotive fuse in series with the battery. The battery probably has protection circuitry, but who knows how much power this battery can supply before protection shuts it down. I use...

This was a substantial enterprise that involved making the spheres, printing the gores, building sturdy stands, packing, and distributing them across Europe. Mercator was also renowned for his scientific instruments, particularly his astrolabes and...