3d printed thor hammer

Building Instructions: Assembly: Print all parts first. Put an M3 nut into the opening of the parts called SensorPhotoTransistor and SensorLED. Put these two parts into the water meter main part. Slide rods through holes in the main part and the...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

This is a ventilation system for an IKEA Lack enclosure.The top and bottom flanges have a “key” that will align the two halves so that the screw holes line up as well as the notch that can be used for servo and/or fan cable management if you wish to...

The transformer comes in 2 Variants and you could either print it complete or in parts however you want to. ... ________________________ <b>If you like my work please consider supporting me on Patreon.</b> <a...

These models should be also shrank to 80% scale when printing.If "1min-holder-1.stl" is too thin, use "1min-holder-1-thicker.stl" instead.note : Since the number of optional files increase, it might be now confusing to add them here. So please...

--------------------------------------- The new Spool Winder: You will need: Print the winder parts: WinderHandle - need 1 WInderHub - need 1 WinderLeft - need 2 WinderRight - need 2 SpoolHolderBaseA - need 2 SpoolHolderBaseB - need 2 Hardware...

I printed a scan of the front of the hull and then glued it with dichloroethane. For cooling grates, I used modifier objects, as well as the author of the original project. I added mounting brackets and spacers to secure the power supply under...

In a pinch (if your printer has issues printing these tiny bastards), you might be able to get away with some clipped up bits of the unused horns included with your servos. I designed the junction of two shoulder pieces to be held by two 3mm x 6mm...

Although these files have not been extensively tested through printing, they are intended to be resized to match common modelling and miniatures scales. Target scale - Scale STL files to: - Notes 1/3900 - 0.25641026 - FASA miniature scale 1/3788 -...

I provide an easy-to-print alignment tool to ensure the heatsink is perfectly positioned for the cover to fit.\n* Direct airflow through the heatsink, don't leave proper airflow to chance.\n* Duct air in one side and out the opposite to maximize the...

So I like to print a test piece before committing to anything big or sensitive. I find that making a piece of OS-Railway track using whatever filament is intended for the project is usually enough to warm up the bed and predict if the printer can be...

-AUTO TRANSLATE TO ENGLISH- After 3 years of using my mobile charger (huawei P30 PRO) the connector had started to break slightly (surely my cat biting it and dragging on the ground helped) so I decided to print a protector. The regular models were...

K40 Paint Rack I recently started painting sla printed miniatures. Soon a lot of 25mm paint flasks crowded my workspace. So I was in need of some paint rack. I searched thingiverse but found none that appeals to me and whose parts will fit in my K40...

Use the backlash option to allow for the gears to work with printing inaccuracies. Bevel gears are more complicated. Meshing bevel gears have the same cone distance, circular pitch and pressure angle. The cone distance, circular pitch and number of...

The equipment tray and servo lock **must be printed as one assembly**. I separated them so you easily could make servo lock for different servo (in that case I use 1181MG servo). I made the square on the equipment tray floor for you to easy pairing...

Tips Be sure your Z axis is positioned so that the endstop is above the level of the print bed before you begin the z probing procedure. You can also use the adjustment for raising the Z axis when probing to help. Finally, I welcome all feedback. It...

all parts: layer height 0,2mm infill 10% to avoid an elephant's foot and thus to achieve an optimal fitting width, you can also print the plates with raft. a maximum of 100 pieces are needed. you can clip them by hand into the holders of the frame...

You'll want to print two each of the bottom stops with and without dowel, and as many of the top stops as you care to use to mark your positions. To finish/calibrate the stops, do the following: 1. Glue/epoxy 1/4" dowels into the holes. These...

Then generate and print one using this bearing generator. I've use it to generate slide and ball bearings for EMT electrical pipe and 8mm rod. There are lots of parameters with defaults for most settings. This design requires omdl.The ball bearing...

Also, the "spikes" on the gripper didn't print well and had layer separation. The gripper is the part that connects onto the end core which pulls out. It uses a screw to tighten it. There are 2 gripper versions based on if you have the normal...

Only a few parts are needed and it is easy to print, preferably in PETG.You can mount it in different ways, on a tripod, with a table clamp or simply with screws.I would still have to work a little on the software, but it works so far.The stepper...

Be sure to print the version appropriate for your application. In order to mount 12mm/14mm wheels to the adapters you first need to install <b>(1) M4x12 or longer socket head screw</b> through the center of the adapter (see pictures for...

for parts look at the parts list PDF that can be found in the FGC-68 starter kit to actually see how to do it whats this link.https://youtu.be/M_1AAlgVm-4 some tips disassemble the FGC68https://www.youtube.com/watch?v=pDRv5jwRReA a introduction to...

For the actual printed parts, this is designed for the tolerances I have experienced with hole shrinkage. It is intended to be relatively tight to the shaft so gently clean out the hole and push onto the shaft. It may take a couple of times to get...

Shoulders and Forearms (https://www.aguilarworkshop.com/product-page/odst-battle-armor-arms) Armored Plate Carrier (https://www.aguilarworkshop.com/product-page/odst-battle-armor-armored-plate-carrier) Utility Belt/Waist...

... made it somewhat modular so you could make them taller or shorter. The outer pieces are printed in vase mode and just glued together.I used a 0.8mm nozzle for the outer transparent parts for some additional speed and rigidity.

Print at 0.4mm nozzle, 0.2mm layers, otherwise all design tolerances will be wrong. It is a good idea (maybe essential) to specify 0.4mm wide outer perimeters in your slicer. PLA works fine. Supports are required, but only because of one very...

It only added a couple of minutes and grams to just go with a solid print. I renamed the other files for clarity. I'll add more info as things are tested and refined.</p><p>The parts list is as follows:</p><ul><li>1.5mm (1/16") silicone rubber in a...

The FC mount can be printed using either flexi or solid filament, but flexi gives the FC added vibration damping. The motor dampeners are designed to be flexi as well, but they're not essential for the build. The FC of choice cannot use pinned...

... for personal use only, non-commercial, not for resale! You cannot sell the digital model, a derivative or adaptation of the model, nor can you sell prints/builds of the model. ... Instagram: https://instagram.com/srheuropecom?utm_medium=copy_link