3d printed tec 9

Truth be told, I've modeled most of the basic pieces, but printing has been slow since my printer died over the summer.) *** NOTICE UPDATE END **** Open Dungeon Tiles We're still here - we went to the mountain to beef up on Blender. Have new designs...

Also (constructive) criticism or exchange of experiences is welcome! Please also have a look at my designs on https://www.thingiverse.com/rolfmobil/designs and https://cults3d.com/en/users/rolfmobil/creations. under the same username (rolfmobil)......

Once I print some more of this I will keep tweaking it - and look to finish meshing a magazine. Nov 29, 2019 Part 2 - YEEUH. HUGE update! I've found a way around a lot of the hard stops of the limitations of space and dimensions, but still...

# Warning **PLEASE PRINT OFF THE SHROUD AND MOCKUP 4010 BLOWER AND CONFIRM FITMENT BEFORE PURCHASING OR MODIFYING ANYTHING! PLEASE POST IN THE COMMENTS IF THIS SHROUD WORKS FOR YOU AND WHAT CARD YOU HAVE INSTALLED** The shroud is designed to sit...

How to put it together?It consists of 6 pieces of printed and screwed parts (fig.):● screw any long M3 screw into the hole of the PIN part to create a thread in it andunscrew it again● insert the BRACKET (right hand under the (+) mark and left hand...

___________ The whole Space Pirates collection comes pre-supported and has been thoroughly print tested. It was first available on our Patreon channel in April 2021. ...Our Patreon creates different collections of sci-fi miniatures each month -...

____________________________________________________________________ BetaFlight Tune: ``` set p_pitch = 100 set i_pitch = 50 set d_pitch = 70 set f_pitch = 125 set p_roll = 90 set i_roll = 45 set d_roll = 65 set f_roll = 125 set p_yaw = 65 set i_yaw...

Building Instructions: Assembly: Print all parts first. Put an M3 nut into the opening of the parts called SensorPhotoTransistor and SensorLED. Put these two parts into the water meter main part. Slide rods through holes in the main part and the...

this should be intuitive ISSUE ADDRESSED 1 OF 3, The manufacturer claims a print area of 240mm x 290mm. (I don't think I was getting even that!), but more could be squeezed out with alternate parts The issue is with the wheels that are mounted to...

Note that the Base Plate was not countersunk in the model for ease of printing and to allow the user to choose the fastener style. Bill Of Materials: (1) Mount Rev0 (1) Base Plate Rev0 (1) Adapter Spacer Rev0 (1) Holder (4) M3x20 Steel...

The secondary goal was to keep it simple and quick to print.The tripod consists of the following components:Tripod Head: Featuring fixed holes positioned at 20 degrees from the central axis.Telescopic Legs: Made from 6mm outer diameter and 4mm inner...

I don't remember what size o-rings were used, but print the piston so that it just fits inside the 1-1/4 PVC tube and try different sizes until they make a decent seal. It doesn't need to be tight. I also sealed up three of the pass-through ports...

The mounting holes are identical between that and the Creality 4.2.7 silent board, which is what I have installed in the first 'final' print. The stock 4010 fan fits upright screwlessly in a mount that holds it to the side of the case, and a buck...

Files to print: ========== - 2x __optical support v3.stl__ - Support for the optical Endstop - 2x __Ender 5 - Endstop trigger v1 15mm.stl__ - Parts to trigger the optical endstop 15mm should be the one you need but I included a shorter one just in...

Presupported and Test Printed!   Ironside soldiers are a type of android designed to function as soldiers or enforcers. They are humanoid in shape, with a durable metal exterior that gives them an intimidating appearance. They are equipped with...

I had just finished printing and attaching the V7 fan duct when I took that pic, so I know the whole thing works. However, the picture shows an earlier rendition of the carriage. I moved the inductive sensor mount to the right a couple millimeters,...

I haven't printed the version with the hole for the reset button, I can reach in the USB hole with a spudger and poke the button so its not essential for my current project. https://www.tinkercad.com/things/hP2VRmHu4Q0 When I get round to making the...

It is represented the inner part of the cold region of the disk, which is about the diameter of Pluto. The "middle" cold disk goes almost as wide as Saturn. The disk is actually a lot less thicker than this, but it is was made like that in order to...

Requires 18mm or ¾" holes in the lid and tub for mounting - use a spade bit for a cleaner cut as these containers are quite brittle.A full unit requires 1x Post (Lower), 1x Post (Upper), 2x Sleeves, 2x Through bolts, 2x Bearing Cups, 3x Arm (Hole),...

The two `o_ring` files are optional o-rings you could print with flex filament. Better to use o-rings, and at a pinch you can probably get away with using a rubber band, or just pushing everything together and putting up with water splashing...

It doesn't cost you anything extra, but helps me out a lot :) Both links in this post are affiliate links. Print instructionsCategory: Hobby Summary Update: I added a second version of the top part of this case, which has a cut-out for those who...

Here is an example of how you could extract and print these lists in a Python script: ```python import json # Assuming that the provided JSON string is in a variable called 'json_str' json_str =...

Remove the short piece of filament, reinsert the bowden tube into the coupler and print without the worry of irregular flow. #Other side effects: From time to time your bowden tube in the hotend will perish due to heat and need replacement. ...

I wanted to print this awesome design by HexiBase on my Ender 3 but the two halves were too big to fit on the build plate so I split each one into two smaller sections. The two sections are joined together via a tongue and groove arrangement, making...

Cut in smart pieces for easy printing. Lyzz Kaboom - Goblin Lady (Fantasy Pin-Up)This crazy Goblin lady is passionated about explosives and traps. She recently assembled a huge amount of giant missiles with Zipzaap with the plan to launch a bunch of...

It is composed of 3 parts to be printed: - The main box which contains the plants. - A diffuser located on the upper part of the box and which allows you to water the plants - The frame which is used for the aesthetic aspect (hide the box) as well...

The LED-tube itself is printed from transparent plastic. Feel free to install a lipo and a step-up-converter or whatever you want ... There are three versions of the body, for - arnuino nano - node-esp8266 development boards - 49 x 26 mm -...

... done, carefully install your Pi in the bracket, being careful with the pins and make sure all 5 pins go smoothly into the Einsy board. Click the Pi in place so the four printed posts in the corners are flush withe Pi's PCB. ...Snap the cover on.

Order of Operations !!!CAREFUL When you are done printing and are removing supports, make sure to be very careful on the Mainboard side. There is a 5th screw that is buried in the support material so just be careful that you don't rip it off. Won't...

Various layouts to organize components and tools to keep everything close by so you can make repairs without leaving the table Print instructionsUn pequeño taller para poder trabajar en el salón de tu casa sin quemar nada y teniendo todas las...