3d printed tec 9

Alternatively, one could print the breasts and make an elastic mold. Step 1 If you look at the breast from the front and imagine a ball in the breast; what diameter would the ball be? <b>Bd= x (mm)</b> If you look at the doll's chest from...

If you don't use your Western Digital MyPassport Pro all the time, but more like once or twice a year as a backup device for your camera, the battery might be damaged through constant drain of stand-by electronics. My last device died of this since...

I added the printed parts to it. The latches are removable and allow the cover to be released with the beetles. For that I use an M6 rod which crosses all the pieces of the slice. BE CAREFUL to only glue the end caps to the rod once the other parts...

I need my printer to be able to use stronger higher temp materials and be able to print delicate single perimeter components for the wings and fuselage. I decided a direct drive upgrade would be a good upgrade to provide better performance and higher...

Printing Select the vertebrae that you need and import them into your slicer. You will need to apply supports to the bony parts that stick out the back and to the sides. IMPORTANT: Be sure to label the vertebrae as they come off the printer! ...

I figured out the airflow issues and designed this print as one of many modifications I made. Since the case isn't terribly efficient at exchanging ambient air, I created this CPU shroud to prevent hot air from recirculating back into the heatsink. ...I...

This is to allow for easy switching of 6V battery to USB power and vice versa, without any alteration on the wiring side.Caution: Make sure your LEDs polarity is correct before you solder them in place (refer to the manufacturer design drawing for...

The filament used is all dark red PETG eSUN brand, printed at 245 ° with bed 80 °, 100% infill to avoid any deformation in the heat. The description is not detailed simply because it is not complicated as a project, certainly a bit of manual...

# OpenSCAD Fully parametric drawer cable storage management hive with punch cuts (openscad-hex-cable-hive-fully-parametric)OpenSCAD Fully parametric drawer cable storage management hex hive with punch cutsThis is an OpenSCAD sketch to generate fully...

Remove the short piece of filament, reinsert the bowden tube into the coupler and print without the worry of irregular flow. #Other side effects: From time to time your bowden tube in the hotend will perish due to heat and need replacement. ...

Both had minor errors that possibly causes them to print badlyUpdate 20.11.2023:-32 and 35 is the same, but the file for 32 is flawed and therefore gets deleted.If you like my work please consider supporting me on Patreon.Become a Patron!Some of my...

I provided an easy-to-print alignment tool to ensure the heatsink is properly positioned for the cover to fit.\r\n* Duct airflow through the heatsink, don't rely on proper airflow by chance.\r\n* Duct air in one side and out the opposite to maximize...

#Printing tips Parts are designed to favour interchangeability and symmetry between ENG1 and ENG2, so they are easier to replace. **STL files are oriented randomly, please adjust side facing the bed so you get the least amount of overhanging...

Also, the "spikes" on the gripper didn't print well and had layer separation. The gripper is the part that connects onto the end core which pulls out. It uses a screw to tighten it. There are 2 gripper versions based on if you have the normal...

Plus more being added please see table belowSorry Painted in lettering and not double colour printing, Found a very light soft grit sanding made using the fibre tipped acrylic paint pens easier to use.&nbsp;Taken from...

These three stls have different wall thicknesses: | part | wall mm | |-----|-----| |thinwall_20_30_10_0p50.stl | 0.50 | |thinwall_20_30_10_0p60.stl | 0.60 | |thinwall_20_30_10_1p00.stl | 1.00 | I printed the pictured rough white part back in 2012 on...

No print support needed!This is an as-is project, will not improve it any further.It works great, cooling is better than stock, it's solidly attachedonly downside is limited visibility on the nozzle.This is a bit weird to setup due to the metal plate...

You don't need to print anything to get it working. Another thing I noticed, If you extrude filament on the button and then press again to stop. The hotend does not switch off on this printer. Kids fire hazard if left on Of course if you went...

このモデルは以下のモデルの自己Remixとなっています。 CE32A 1" Speaker Driver Enclosure PAM8403-based Tiny Audio Amplifier Board Adafruit Stereo 3.7W Class D Audio Amplifier MAX98306 Enclosure Adafruit Breadboard Friendly 3.5mm Stereo Headphone Jack Enclosure Adafruit USB...

Assembly Method: So we looked at what was out there and wanted to simplify current designs as much as possible, we also wanted to design for laser cutting so these can be mass produced. -Its laser cut so 100-1000 can be produced a day -We...

...Both parts are easy to print without support structures. For reinforcement, the part to which the pool pipe is attached with screw clamps has a reinforcement. The hole in the container is approx. 45 mm and was actually drilled for the rubber sleeve.

Printing of a second prototype is in the works. 2. Centrifugal wheel friction. If the wheel spins free and touches surrounding parts it can "weld". This can be prevented by a very careful alignment of the impeller so that it doesn't touch the...

This design is intended to be a relatively affordable, simple and easy to print electronics project. Remix as required to add a secondary sensor, extra valves, etc. I have uploaded the most current Parasolid assembly file so feel free to dive into...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

Assembly video (in Russian): https://www.youtube.com/watch?v=rt2GikOnDV8 The parts are printed with PLA plastic, the body and struts are 100% infill, the wheel guard mounts are 75%, the wheels are 50%. When assembled, my copy weighs 1466 grams. ...

The Therion Ifrit is a large model around 120mm tall.  He has been sculpted and posed to print as a single piece on a 5.5" build plate with his base separate.   Presupported files are included for each model in both STL format and LYS (Lychee...

You can see my setup running DOOM 2016 (which my laptop cannot normally do) in the images above.Video: https://www.youtube.com/watch?v=nLmP1UIUPW4Edit: At the request of Lasklo, added a version of the bottom without the cutout for the power override...

In a few million of years Eros could change its orbit to a lower Earth crossing one, becoming a member of the Apollo or Aten group. Depending on how close it became to the Earth, it could be a Potentially Hazardous object (PHO), an object capable of...

Using it I created 12v powered Media centre with LibreElec running KODI so that I could watch TV-shows or movies in my RV without having to bring disks with me or have access to streaming services. I load the HD up with my ripped DVD's and then just...

If you want to use Anet's original M5 screws/t-nuts, just print the parts with 100% infill and drill out the mounting holes with 5.0 or better yet, 5.5mm (to give you some alignment room) drill. Edit: Full screw list, as requested: * 10pcs of 412...