3d printed spoon rest

So, make sure that you really want to install the screen inside the case before cutting the ledges.\r\n\r\nSee the printing instructions for more information.\r\n\r\nSorry about the distorted images - somehow Thingiverse lost the ability to scale...

https://www.thingiverse.com/thing:3589645 Problems: checksumme error while printing from SD-Card at TFT32 #Deutsch# Adapter für Bigtreetech SKR 1.3 zu Anycubic I3 Mega Firmware is for TMC2208 2.0 or higher with UART (ohne Filamentsensor...

Preparation * Print the puzzle components * Have phones or tablets with the Aurasma app installed * Provide students with 20-25 minutes to solve the puzzle References The math involved in this puzzle is relatively simple, so no references are...

keep additional ons as you see fit for the meter, USB etc - do the same for the live for any separate circuits you may add - create a harness for the banana plugs, and anything else you can before you start assembly - I suggest adding at least...

During printing the holes can sometimes be narrower. Therefore it may be necessary to drill them out. Take one thread and make a multiple knot at one end and then pull the thread through one hole. Place the top ring with the bottom side facing up. …...

The attachment itself is designed as a two-part unit for easier printing without supports, with the lower part serving for connecting the battery (it is possible to choose a version for Makita or Parkside batteries) and the upper part forming the...

... it seems to work better, I will try another size that reaches the top, when I reach the 35cm. Anyway, the improvement is extraordinary, the squares of the photo are printed with 1 single layer of skin and without filling. ... Translated by Google

This is an interference fit, you may need to sand it a bit to get it to fit, my test print barely fit on my carriage. I used a large nozzle with PETG as the test, which tends to skew the dimensions a bit, if the fitment is loose/tight let me know, I...

Follow my print instructions for optimal results. --- *** UniPod *** Camera: The pod will fit a foxeer predator, runcam swift miro, caddx micro. Almost any micro camera will fit. VTX Antenna: There is an integrated mount inside the canopy for a...

I have included the STL files that I used for the demo parts - all were printed on Lulzbot Mini with eSun ABS. This printer has a 0.5mm nozzle (if you use these demo STLs with a smaller nozzle, the fit might be loose). The file names are ridiculously...

The pegs are quite thin, so it's best to print them with a layer height of 0.08mm. This setting should make the pegs strong enough to hold up to inserting into the bracket but flexible enough to slip into the bracket with little force. I've also...

You can also refer to this video from Embrace Making for dissasembly assistance, it helped me so much when I was trying to do this I've tested it on all-metal version with dual-fan setup, you can refer to my klipper config if you need to (Please...

You like this print? Maybe have a look at my other designs as well: Link: https://www.thingiverse.com/lexx3d/designs ----- Deutsche Version ----- Ich mag fummelige Sachen nicht und einen Zylinder in 2 Ringe wie bei den meisten Haltern zu...

I also included a Voron logo insert that I printed in transparent filament that may utilize some additional LEDs in the future. Note that it did require a little post-process filing to get it to fit. Also note, that the clearance between the heater...

Includes an alternative top with a spot to mount a 30mmX30mmX8mm fan such as these: https://amazon.com/gp/product/B07QJ4MS2L Instructions I printed mine in PLA, 0.3mm layer height, no support. Files for two "Top" pieces are provided, the standard and...

A VESA mount is included with the Intel NUC, which you'll use to attach the NUC to the new printed plate. The NUC doesn't come with a screen. I use a 7-inch capacitive touch screen from Amazon, specifically the GeeekPi 1024x600 model. You can find...

FYI, I am using an FDM printer for the base unit and anything that pops up through the pie panels I am printing in resin. Here is a video link of my electronics mock-up: https://www.youtube.com/watch?v=h6nXO9jEetk Base Unit Lower Limit...

If your job isn’t the kindest, print this out and keep it with you, there’s always a worse job, like trying to live and work on this thing in the middle of a violent fast moving, constantly moving, lightning flashing orange and black sand storm you...

Printing in the orientation that's generated makes the smoothest surfaces for the ball bearings. The best airtight container I've found for this purpose is the Sistema KLIP IT Bakery Box (about $9 on Amazon...

It won't work as printed without additional machining. When I ordered the tie rod ball joint pack set from Robotdigg (DR001) I discovered it came with two different types of ball ends. Since most carriages and assembly plates are 40mm width, I...

https://youtu.be/LYm1B4P_h8A The two-layered planetary system of the "quick print" version was also only intended for calibration and demonstration. As you will find, the planet gears will twist under load and the clamping force will be quite...

... different position on my D9, and I'd appreciate feedback on that. Also, there's a chance for the duct to almost touch the print surface when you have a very short heatbreak. ...So, don't install your all-metal hotend on the topmost position.

from standard signs to oval or circle shapes Multigon shapes Triangle/Pentagon,Hexagon,Octagon up to 8 Text Lines many carefully preselected high quality Fonts Various Font Styles, adjustable Line & Character Spacing positioned freely ...

The fit of the Pi 4 in it hasn't been verified yet since I haven't printed it. Boxes for the Pi 3 and Pi 4 with the Pi shifted to the right side and a small cutout directly across from the USB power connector have also been added. This allows you to...

For the same price of one tent pole could buy 2 x 6.5m lengths of Al tube, and a roll of filament. Took a few attempts but the twist lock cams were very easy to design and print and worked far better than expected.  The larger version...

You get the following figures in both our standard 36mm scale and a smaller 32mm scale so you can choose your prefered size: - Operative Balakin weilding a flamethrower - Operative Alekseev dual weilding a flamethrower & uzi - Operative Federov...

For printing I just made everything 50% Gyroidial infill, with ESUN PLA+. Did a bunch of pretty serious drop and smash tests with early iterations and the unit held up pretty damn well. I got the makita mount from somewhere a while back but cant...

Printing info: Felix printer was used Resolution : .15 layers and higher Supports needed. 100% infill for a heavy tool that needs durability at its core Assemble these pieces easily: - Lay the 'slider' in 'lower body' (feet towards...

Print the nose with supports everywhere and 20% support density, also use 20% support density with support brim, support roof, and support towers enabled on the LID. Use four walls and 20% infill or more on the nose, and 40% on the LID - the lid...

I wanted to fit some lighting to the Kossel so I could monitor overnight prints remotely without having to leave lights on all night. The Neopixel range of addressable strips and rings seem to fit the bill as they only need a single data line for all...