3d printed speedloader

Assembly video (in Russian): https://www.youtube.com/watch?v=rt2GikOnDV8 The parts are printed with PLA plastic, the body and struts are 100% infill, the wheel guard mounts are 75%, the wheels are 50%. When assembled, my copy weighs 1466 grams. ...

The alternative file is what is in some of my first renders and does look cool, but they are often annoying to print and glue on the vehicle so adding them is up to you. Size of model when completed 165mm length, 90mm width, 68mm high. ...Instructions...

___________ The whole Space Pirates collection comes pre-supported and has been thoroughly print tested. It was first available on our Patreon channel in April 2021. ...Our Patreon creates different collections of sci-fi miniatures each month -...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

It is represented the inner part of the cold region of the disk, which is about the diameter of Pluto. The "middle" cold disk goes almost as wide as Saturn. The disk is actually a lot less thicker than this, but it is was made like that in order to...

The equipment tray and servo lock **must be printed as one assembly**. I separated them so you easily could make servo lock for different servo (in that case I use 1181MG servo). I made the square on the equipment tray floor for you to easy pairing...

40x55mm.you need 2 pieces of rubber band, wire or tape.you need 1 piece of Periscope tube 01 or standard 32mm PVC tube.(Periscope tube 01 89mm long results in a Periscope in/out of 150mm)But you can also use standard 32mm PVC pipe to get a larger...

I wanted to print this awesome design by HexiBase on my Ender 3 but the two halves were too big to fit on the build plate so I split each one into two smaller sections. The two sections are joined together via a tongue and groove arrangement, making...

#Printing tips Parts are designed to favour interchangeability and symmetry between ENG1 and ENG2, so they are easier to replace. **STL files are oriented randomly, please adjust side facing the bed so you get the least amount of overhanging...

Print these two pieces out then hot glue them to your broom and refrigerator. My broom has its brush cut at an angle, so orient it so that it naturally falls over towards the back of the fridge. I designed this for a .85" diameter broom stock. Let...

Note: Someone has mentioned the possibility of additional electromagnetic interference generated by the psu by removing the metal lid, so I may try to print this later in conductive filament. As of now, I have yet to experience any downsides of using...

I haven't printed the version with the hole for the reset button, I can reach in the USB hole with a spudger and poke the button so its not essential for my current project. https://www.tinkercad.com/things/hP2VRmHu4Q0 When I get round to making the...

Also (constructive) criticism or exchange of experiences is welcome! Please also have a look at my designs on https://www.thingiverse.com/rolfmobil/designs and https://cults3d.com/en/users/rolfmobil/creations. under the same username (rolfmobil)......

The mounting holes are identical between that and the Creality 4.2.7 silent board, which is what I have installed in the first 'final' print. The stock 4010 fan fits upright screwlessly in a mount that holds it to the side of the case, and a buck...

It is composed of 3 parts to be printed: - The main box which contains the plants. - A diffuser located on the upper part of the box and which allows you to water the plants - The frame which is used for the aesthetic aspect (hide the box) as well...

Print Settings Nozzle size = 0.4 mm (minimum, smaller better) Layer height = 0.2 mm Filament change layer for colours on "300ZXBoxBack": 1) Start (Colour of the background, mine is in white) 2) Layer 14 (All logos outline and "Twin Turbo" letters...

I printed the part using supports which are only necessary for the corners to the upright face. -- x -- I've also included a camera housing for the rear camera (plus fittings). It is intended that this will be attached to the upper plastic trim...

------------------------------ PRECAUTION: Après quelques prints, il faudra contrôler que les tensions soit toujours bonnes. Procéder à un ajustement ci nécessaire. ----------------------------- Ce custom est un projet personnel, qui m'a pris...

Please reorient the STL when slicing and printing such that these features face up. ** Note: 2022-02-04 -** the original has been revised to remove any isolated (single square) "towers", called the rev. 2 version. These were found to be weak and...

These models should be also shrank to 80% scale when printing.If "1min-holder-1.stl" is too thin, use "1min-holder-1-thicker.stl" instead.note : Since the number of optional files increase, it might be now confusing to add them here. So please...

Although these files have not been extensively tested through printing, they are intended to be resized to match common modelling and miniatures scales. Target scale - Scale STL files to: - Notes 1/3900 - 0.25641026 - FASA miniature scale 1/3788 -...

The support piece in the D-pad space will punch out with a punch and hammer after printing.Just place the shell on something with free space under the D-pad area and punch the support piece. Wiring the 9-pin d-sub for Amiga, Atari, Kempston or SEGA...

The built-in socket has the advantage that no cables can be seen. Tools you will need: (see the pictures) Hot glue, super glue, soldering iron, screwdriver, ... Print instructionsCOMPONENTS: Attiny85...

The two `o_ring` files are optional o-rings you could print with flex filament. Better to use o-rings, and at a pinch you can probably get away with using a rubber band, or just pushing everything together and putting up with water splashing...

einfach Fragen! Print instructionsUnassociated tags: 7 segment, 7 Segment Uhr, LED clock, LED Uhr, RGB Uhr Category: Household Summary Ich benutzte PLA in schwarz und farblos-transparent Benötigt werden folgende Teile Druckteile: jeweils 4 Stück:...

Again, check several times before you drill. Overview of some assembly steps and setup here: https://youtu.be/QQAKxDcRNgc Print Settings Printer Brand: Prusa Printer: I3 MK3SRafts: No Supports: YesResolution: 200 Infill: 15% Filament: Mainly...

... done, carefully install your Pi in the bracket, being careful with the pins and make sure all 5 pins go smoothly into the Einsy board. Click the Pi in place so the four printed posts in the corners are flush withe Pi's PCB. ...Snap the cover on.

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

The secondary goal was to keep it simple and quick to print.The tripod consists of the following components:Tripod Head: Featuring fixed holes positioned at 20 degrees from the central axis.Telescopic Legs: Made from 6mm outer diameter and 4mm inner...

for those who download an try it, all i did was use m4 bolts stuck inside the ends of the tubes after going through the arms then zip tie around the threaded section of the bolt to keep it from slipping out, but do whatever works best for you, i...