3d printed skyscraper

No print support needed!This is an as-is project, will not improve it any further.It works great, cooling is better than stock, it's solidly attachedonly downside is limited visibility on the nozzle.This is a bit weird to setup due to the metal plate...

Just put the LEDs and alarm speaker in a box with a labeled side (printed in white filament) and attach it to power supply fan connector... there is even a slot in my power supply cover to allow the wire to be slipped into (and out of) the power...

I recommend printing them too. Intentionally the Main Box fits 6 of the Double Mini Card Containers, one big Tarot Container, 6 Standard Card Containers and the two Token Holders. If arranged correctly you'll be able to replace one double Mini...

All parts should be printed first. Then the holes are drilled: the hinges with 4mm and the screw holes with 3.5mm. This gives you optimal support and a high degree of accuracy. The brackets are designed for doors with a 2mm distance from the...

&nbsp;After you print 9 pins and rollers you can force a bearing on each end of the rollers, put a dab of super glue in the sunken pin hole and then set the pin through the body and roller to secure it. &nbsp;Rinse and repeat. &nbsp;</p><p>I had to...

Tips Be sure your Z axis is positioned so that the endstop is above the level of the print bed before you begin the z probing procedure. You can also use the adjustment for raising the Z axis when probing to help. Finally, I welcome all feedback. It...

Parts are not oriented for printing. The STEP file is included for easy remixing. I am not an electronics expert but I did the best I could with the design, but still make this at your own risk and let me know if you see something that can be...

Plus cardboard is an amazing garden soil nourishing element. PrintingPrint all the parts with a 0.4mm nozzle (or using the preconfigured files for PLA)  0.6mm for PLA-CF:Matrix : 0.1mm layer height for the bottom grid, then 0.2mm layer height, 20%...

#Printing tips Parts are designed to favour interchangeability and symmetry between ENG1 and ENG2, so they are easier to replace. **STL files are oriented randomly, please adjust side facing the bed so you get the least amount of overhanging...

I printed a scan of the front of the hull and then glued it with dichloroethane. For cooling grates, I used modifier objects, as well as the author of the original project. I added mounting brackets and spacers to secure the power supply under...

I have NOT built or printed this option, but I am confident it will work fine. You can probably source some thin material to take up any slop in the assembly - even the sheet of foam that is provided in the original tinySA packaging box could work...

The FC mount can be printed using either flexi or solid filament, but flexi gives the FC added vibration damping. The motor dampeners are designed to be flexi as well, but they're not essential for the build. The FC of choice cannot use pinned...

My work shop is embarrassingly messy at the moment but I have tested them and they seem to work as intended. Print instructionsThe parts were designed to not need supports you will need to use a knife, razer blade and/or deburring tool to cut out the...

K40 Paint Rack I recently started painting sla printed miniatures. Soon a lot of 25mm paint flasks crowded my workspace. So I was in need of some paint rack. I searched thingiverse but found none that appeals to me and whose parts will fit in my K40...

# Warning **PLEASE PRINT OFF THE SHROUD AND MOCKUP 4010 BLOWER AND CONFIRM FITMENT BEFORE PURCHASING OR MODIFYING ANYTHING! PLEASE POST IN THE COMMENTS IF THIS SHROUD WORKS FOR YOU AND WHAT CARD YOU HAVE INSTALLED** The shroud is designed to sit...

Only a few parts are needed and it is easy to print, preferably in PETG.You can mount it in different ways, on a tripod, with a table clamp or simply with screws.I would still have to work a little on the software, but it works so far.The stepper...

This is to allow for easy switching of 6V battery to USB power and vice versa, without any alteration on the wiring side.Caution: Make sure your LEDs polarity is correct before you solder them in place (refer to the manufacturer design drawing for...

Welcome to the home for the things to print for the Eff-Uno Racer project (https://github.com/oracle-devrel/eff-uno-racer). Eff-Uno Racer is a LEGO© Open Wheel Race Car that you can build and remotely control. Most of it is made with LEGO© bricks...

Then generate and print one using this bearing generator. I've use it to generate slide and ball bearings for EMT electrical pipe and 8mm rod. There are lots of parameters with defaults for most settings. This design requires omdl.The ball bearing...

If you'd like to buy a print of this with metal inserts in the drill holes, please check out my gunbroker page: https://www.gunbroker.com/item/858377600 This is version 1.2 of the C93 paddle release jig I previously released. This updated version...

for parts look at the parts list PDF that can be found in the FGC-68 starter kit to actually see how to do it whats this link.https://youtu.be/M_1AAlgVm-4 some tips disassemble the FGC68https://www.youtube.com/watch?v=pDRv5jwRReA a introduction to...

... ends at the posts) 8.) To mount it match drill using the fitting into the side of the psu and run two machine screws with a nut. (Bonus points if you use Loctite or a lock nut on the nut.) Print Settings Rafts: No Supports: No Category: Electronics

Because of the height of the box, the width of non-snug sleeves, and the text size required to come out visible without a .25mm nozzle (and by Thor, I would not want to print all these separators with that!) it became necessary to make the dividers...

(STL included for the feet: print four of them in TPU for best handling of vibrations) * Low version, which does not require feet to lift the Ender 3 Pro. There is no slot for a fan however. Use at your own risk as my advice is to always use active...

Printing of a second prototype is in the works. 2. Centrifugal wheel friction. If the wheel spins free and touches surrounding parts it can "weld". This can be prevented by a very careful alignment of the impeller so that it doesn't touch the...

Print all the parts before assembling anything. 4. Start by assembling all the windows, doors, and trim as shown in image 1. 5. Assemble the motor mounts by gluing the two halves together. Ensure you align the holes before gluing. 6. Attach them...

Printing Select the vertebrae that you need and import them into your slicer. You will need to apply supports to the bony parts that stick out the back and to the sides. IMPORTANT: Be sure to label the vertebrae as they come off the printer! ...

Shoulders and Forearms (https://www.aguilarworkshop.com/product-page/odst-battle-armor-arms) Armored Plate Carrier (https://www.aguilarworkshop.com/product-page/odst-battle-armor-armored-plate-carrier) Utility Belt/Waist...

Once I print some more of this I will keep tweaking it - and look to finish meshing a magazine. Nov 29, 2019 Part 2 - YEEUH. HUGE update! I've found a way around a lot of the hard stops of the limitations of space and dimensions, but still...

Note that the Base Plate was not countersunk in the model for ease of printing and to allow the user to choose the fastener style. Bill Of Materials: (1) Mount Rev0 (1) Base Plate Rev0 (1) Adapter Spacer Rev0 (1) Holder (4) M3x20 Steel...