3d printed skyscraper

Using an M3 tapered tap, I found it was relatively easy to slowly do this with no pre-drilling.The thread will, of course, not be complete and that is why a long screw is used in fixing.Assembly:Two M3 nuts should be pressed into the back of the...

Plus more being added please see table belowSorry Painted in lettering and not double colour printingTaken from https://www.thingiverse.com/thing:3079639I used a draft setting, nozzle 215c bed 60c. Label ListAster American...

I wanted to fit some lighting to the Kossel so I could monitor overnight prints remotely without having to leave lights on all night. The Neopixel range of addressable strips and rings seem to fit the bill as they only need a single data line for all...

Preparation * Print the puzzle components * Have phones or tablets with the Aurasma app installed * Provide students with 20-25 minutes to solve the puzzle References The math involved in this puzzle is relatively simple, so no references are...

If you make one or have improvements, please post. Print instructionsCategory: Costume Summary Here is my third version of a costume prop for Tom Clancy's The Division video game. It's some kind of shoulder beacon / gizmo that all the characters...

Print it with 0.2 and 100% infill. IKEA LÖRBY (EUR 9.99) is a USB charger that's powered by a 24 Volt power supply. It delivers a total output of 3.4 Amp and an maximum output of 2.4 Amp per USB Port. This makes it compatible with the Ender 3 power...

However if your task has the property such as finding out paths between the various unvisited nodes where some paths can have multiple lengths because it was given in both weights so then this needs another method of sorting by distance to reach...

I printed about 5 of the sleeves to get the lettering just right and included the gcode so you can get the best quality settings without trial and error. Included are 2 different back covers: one solid and one cut for a 40mm fan (shown in red setup...

8x2,6mm (2 for the bottom 2 for the top)FilamentFor me Bambu Lab or Prusament filament is never a miss for is extremely high quality. PLA:Bambu Lab - PETG: Blue GrayBambu Lab - PETG: WhitePrintingThe files were prepared and sliced with care, with...

ENGLISH DC adapter with 5.5 mm jack output for the Parkside X20v series batteries, compatible with all devices that operate at 20v max. Very useful for the TS-100 soldering iron so that it can be used without the need for household electricity....

The attachment itself is designed as a two-part unit for easier printing without supports, with the lower part serving for connecting the battery (it is possible to choose a version for Makita or Parkside batteries) and the upper part forming the...

Throw a support on the lower half, then just print the upper and head with brims. Sources: Sherlock Holmes and Dr Watson NPCs by mz4250 https://www.thingiverse.com/thing:3333341 Sherlock Holmes Bust by sylvar75 ...

The difference is only in the visible layers, for ease of use. Update 20190819: Added a german version for 3.5mm plywood. Update 20191015: Placed the small parts in containers Post-Printing Assemble instructions The photos after the SVG file show...

Edit 27-10-2018: added the Fusion 360 original This is a second, improved version of http://www.thingiverse.com/thing:1526752 Detachable top part - easyer for transport RGB Color LED for status More sturdy frame Improved software Smaller electronics...

***** Print Settings Layer Height 0.2 mm Infill Density 20% Generate Support - yes. Build Plate Adhesion Type: Brim ****** I controlled the LEDs using an ESP8266 chip and software obtained from: https://github.com/Aircoookie/WLED ***** If...

This is accomplished by printing a column of fanned-out light pipes that radiate from the LED. Continue reading below the videos! Videos: They are all extremely short. Warpcore running at warp factor 2 Warpcore Standard from Novel Mutations on...

I have to find efficient part cooling solution, this one does not cool enough with speeds I am printing now. VERRY IMPORTANT! Use correct lenght screws for motor mount. Slightly too long and mount points will be ruined! Parts needed: 2x 445mm X...

See how it works here: https://youtu.be/B3C8raQL2_4 Instructions Instructions: You will need to print the following parts (all 0.2mm layer, 4 perimeter, 25% infill): 1 gear.stl 1 worm.stl 1 wormbracket.stl 1 bigpulley.stl 1 yoke.stl 1 bladepulley.stl...

magnets, and the more powerful they are, the better.Note that you need to print two of each InsideScrew, outside_screw, and InsideScrew_plug partsPut a small amount of not-too-powerful glue inside the outer grip (1, above), and stick one magnet...

I printed the right and left halves as provided, with no supports but one side had to be flipped 180 in the slicer app. I couldn't do anything with the provided whiskers that stand on-end so I made some up. I decided on 3 different length of...

A major part of this system are bench dogs, and as the metal ones can be quite expensive and you don't necessarily need that much strength in most tasks I figured I'd design and print a set. Same goes for a variety of additional accessories which...

A major part of this system are bench dogs, and as the metal ones can be quite expensive and you don't necessarily need that much strength in most tasks I figured I'd design and print a set. Same goes for a variety of additional accessories which...

Otherwise you may PERMANENTLY DAMAGE your lenses due to the glue vapors as they will stain and ruin your otherwise clear glass. I did some light sanding on the inside of the adapters so that they slide on and off more easily. Qwerty_Uieo made some...

Acrylic Measurements: Top - 20 1/2" X 19 3/4" Front door - 6 7/8" X 17 3/4" Rear - 7 1/8" X 18 1/4" Sides - 3 1/2" X 20 1/2" Printed parts: 40x40 bracket - 10 required 40X40 Front Tabbed bracket - 2 Required --> These work with my Y axis belt...

All other things still apply like changing the name of the .txt files to .h and .cpp respectively.  Printing:All parts saved as STL are in the correct orientation, and the only part that needs supports is the head. It only really needs...

Mine is printed using carbon fiber PETG for the body and translucent green PETG for the top. I'll list out the specific electronic and mechanical hardware that I used below, I know this combo works and pretty damn well at that. If you don't wanna...

In fact I most often just grab these instead of my actual metal bench dogs unless I really need the sturdiness or precision that my metalPrinting InstructionsYou should be able to get away with 0.2mm layer height easily, the XY-resolution is more...

I printed the right and left halves of the mask as provided, with no supports but one side has to be flipped 180 in the slicer app. I couldn't do anything with the original whiskers that stand on-end so I made some. I decided on 3 different length...

Powered by 5V USB or external battery.Step file and fusion 360 file includedTwo sizes of rotating platforms - 80mm and 140mm in diameterFor basic rotation it is possible to use something directly from the example for Arduino (part of Arduino IDE).It...

A major part of this system are bench dogs, and as the metal ones can be quite expensive and you don't necessarily need that much strength in most tasks I figured I'd design and print a set. Same goes for a variety of additional accessories which...