3d printed skyscraper

... for the cost of a pair of 120mm silent computer fans, you can have a silent B1! Oh, and it is so quiet now. All you hear is the fans on the head and the steppers when they move at high speed. :)I printed this on a BIQU B1 using eSUN PLA+ filament.

For the solder roll I used a M8x50 bolt with nuts on either side of each of thewalls to ensure that the 'H' frame stays rigid and the bolt doesn't bend in the thinner wall when tightened.Everything was design in Autodesk Fusion 360.For printing I...

I have included the STL files that I used for the demo parts - all were printed on Lulzbot Mini with eSun ABS. This printer has a 0.5mm nozzle (if you use these demo STLs with a smaller nozzle, the fit might be loose). The file names are ridiculously...

Printer Settings Printer: Kerrby Rafts: Doesn't Matter Supports: No Notes: I suggest printing with thick bottom and top layers. This model is supposed to be scaled up by either 150% or 200% before slicing. How I Designed This Designed using rhino....

... of running pipes to them for water transport and waste management. The angled door arches and angles underneath overhangs should allow this to be printed without supports. Added Version 2. Slices better in Slic3r. ...(tested in 1.0.1 and 1.1.3)

After checking the accuracy of fit with a test frame, I was able to print the complete funnel and fit it with two filters and mount it on the suction cup without any further adjustments. ...After the first test, the suction power is not hindered, the...

* Insert M3 nut into the inset on the top left front of the printed carriage. * Install motor and attach to breakout board * Connect X limit switch to breakout board Cable Chain: * Remove the right side cable chain mount link, then cut out the...

I have NOT printed it yet so I have not verified the fit of the Pi 4 in it. I also added boxes for the Pi 3 and Pi 4 that have the Pi shifted to the right side and a small cutout placed directly across from the USB power connector. This will allow...

Two are required, the shape is rotationally symmetrical so only one model is needed, and printed twice. The jig is 2RU (3-1/2") high which is the same as the smaller PDP-11/03 chassis height. To use, simply push the jig into the rack from the...

The other must have mod is the welding mask, I was able to unsnap some joints on a $10 mask and 'thread' it through the existing holder, then just use the top Velcro strap to attach to the front headband, better than a printed attachment - takes all...

This is basically the **Customizable Better Temperature Tower** by *kmsd3d* including: - several pre-rendered stl files for various filament types - a list of layer change settings - the original customizable OpenSCAD file - an Python3-tool to create...

As the buttons require minimal material, I recommend printing a set of each style to ensure a perfect fit. It is easier to solder all wires to the boards before permanently mounting them in the box. By connecting the common pins on the buttons...

1x Brand NEW Warlock Subclass: Dragon Patron 1x Full size A2 printable map of Greypeak 1x Full size A2 printable map of the city of Vanlund 6x original Battle Maps, including an enormous dungeon (for use printed or digitally) 10x Original Statblocks...

A custom DIY rear light for the Patton.I wanted a solid red light on my Patton that didn't blink all the time and also increasing the visibility overall so I designed this mount for a 5V neon led strip which doesn't require data just positive and...

Since my first-generation 2/3 plane connectors broke due to FDM layer separation issues, all the connectors in this series are printed so all connectors extend out on one plane, meaning that FDM printers are more than capable of building these very...

I printed the waterwheel with an SLA printer because it is easier to get a smooth axle and a balanced waterwheel. The wheel runs slower if it is mounted the wrong way round. So the water runs onto the underside of the blades. I kept the bottom of...

... If you feel comfortable swapping filaments mid-print, try switching the white filament out for some clear filament after layer 2 can help allow more light to pass through. ## No Magnets I'm considering replacing the magnet indents with OpenLOCK.

Button is planned to be wired to a TeensyLC to trigger display on/off by hitting the keyboard "pause" key, and should be printed in TPU. Inner button shelf is sized to fit a 12mm x 6mm https://www.adafruit.com/product/1119 meant to hit the mapped...

# Print Instructions: Be sure to use supports for the wall pin and the gun holder. Take care to clean the supports and leave a smooth finish on the gun holder. I set this up so the gun points to the right to hide the screw holes. If you want to...

All necessary parts for a compact, three-dimensional printed mini tri copter modelled after RCExplorer V3 will need to be acquired. This endeavor relies heavily on David Windeståls impressive design and accomplishments. Those wishing to assist David...

Printing in the orientation generated makes smoothest surfaces for ball bearings. The best airtight container I've found for this purpose is the Sistema KLIP IT Bakery Box, available on Amazon for around $9 at http://amzn.com/B001XSNP00. The...

Feel free to download and print it yourself - total cost under $30, plus your time. I tested this monitor using a tiny whoop's 260mAh lipo battery, which lasted for half an hour. With over 3000mAh Li-Ion batteries, you can expect an operation time...

\nThe changes from vanilla Marlin 1.1 are listed below:\nPrint required items:\n- Left Fan Duct\n- Right Fan Duct\n- Extruder Fan Duct\n- Strengthened Extruder Mount and Spacer\n-Z Probe Mount\n- Extruder Mount Lancewood\nPrint Settings:\nPrinter...

... Note that the edge and corner brackets extend 6mm past the edge of the P5 panels, so make your wood frame 12mm larger than your matrix in each direction. Note - the picture doesn't show all the brackets attached yet because I'm still printing them.

...Both parts are easy to print without support structures. For reinforcement, the part to which the pool pipe is attached with screw clamps has a reinforcement. The hole in the container is approx. 45 mm and was actually drilled for the rubber sleeve.

The final versions here have been modified after I printed the original parts but they didn't fit well due to shrinkage. I've reprinted all the parts successfully at a 2.5 - 3% increase in size for ABS. UPDATE 14/10/2019 Just got my hands on a...

I'm looking forward to rolling up to my next conference and busting out a laptop printed into a Pelican case. A full description and build guide can be found at Oceanography for Everyone. Support more projects like this by contributing to my...

I found in using my original printed design that the holes didn't allow for the kind of seasoning dispersal that I prefer (lots of it!), so I increased the hole diameter from 2mm for each hole to 2.75mm. This should allow for more or larger grains to...

Details include: - `custom_top_outer_edge_chamfer_radius = .6`: defines an extra smooth curve outside all traces including ports which might contribute slightly higher price compared purely printed solutions depending supplier agreements currently...

However, if you're certain it will remain on the bike, you can print the thick version from the start. To complete this project, you'll need some thin stainless steel for the battery contacts and optional locking tab lever. A stainless steel spatula...