3d printed shower

Best printed with PETG at 100% infill. The larger version (stl and 3mf included) are specifically sized for the newer style pumps that use the clip on nylon base. They will work with the screw on style metal base. Usage of the mold/die remains...

Buck Converter (to power my 12v cooling fans) Order of Operations !!!CAREFUL When you are done printing and are removing supports, make sure to be very careful on the Mainboard side. There is a 5th screw that is buried in the support material so...

I used black to match the container) Magnets (8 total): https://www.kjmagnetics.com/proddetail.asp?prod=DC6PC-BLK Mesh: https://www.amazon.com/gp/product/B07563327H/ref=ppx_yo_dt_b_asin_title_o04 o00_s00?ie=UT F8&psc=1 Thermal Adhesive:...

Well I am just to lazy to print twice ;-), of course you can arrange all the “Text plates” and all the “cableTie” parts on a separate buildplate and go from there, that is your choice.Important; for the “Cabletie” Parts, due to sometimes small...

Https://www.thingiverse.com/Apps/Customizer/run?thing_id=739573 Instructions: Using The Following Options: Text Outline Strategy For Non-Latin Scripts = bar and glyphs Outer Edge Color Of Design = gray Displayed Name On Model = kanu Frame Width Is...

...There is a preview .stl--nothing to print yet! Updated with v2 parts 09/21/2017: Added longer V2 parts that use two screws for better clamp support, similar to a woodworkers clamp. If you are shooting for light and cheap stick with the V1 clamps.

This is a thing I call the Sand Raker, it is a very peaceful print when finished and put together. https://www.youtube.com/shorts/fRqaw5RR5FI A kinetic sand piece that rotates via an electric motor with a pinion gear of 11mm, and rakes the...

This design is intended to be a relatively affordable, simple and easy to print electronics project. Remix as required to add a secondary sensor, extra valves, etc. I have uploaded the most current Parasolid assembly file so feel free to dive into...

Installation ------------ Print out the four switch holders and slide them into the aluminium channel on the X and Y axis, as shown in the photos. The X axis holders are slightly longer than the Y axis holders. The tolerance is quite tight so they...

Because of the height of the box, the width of non-snug sleeves, and the text size required to come out visible without a .25mm nozzle (and by Thor, I would not want to print all these separators with that!) it became necessary to make the dividers...

No print support needed!This is an as-is project, will not improve it any further.It works great, cooling is better than stock, it's solidly attachedonly downside is limited visibility on the nozzle.This is a bit weird to setup due to the metal plate...

compatibility note: for my testing did it work for EGO’s and GEO’s the only thing to keep in mind is both those 2 have a slightly different hight so you do need to print 2 separate barrel mounts points in case you have both type of markers and like...

You can set the X_MIN_POS to -1 and the Y_MIN_POS to -24 and the bed size to  234 on X and 211 on Y and then you won't run into issues with it trying to print off the edge of the build plate, you should also change them in the slicer to match. I...

The mounting holes are identical between that and the Creality 4.2.7 silent board, which is what I have installed in the first 'final' print. The stock 4010 fan fits upright screwlessly in a mount that holds it to the side of the case, and a buck...

The FC mount can be printed using either flexi or solid filament, but flexi gives the FC added vibration damping. The motor dampeners are designed to be flexi as well, but they're not essential for the build. The FC of choice cannot use pinned...

Marienkäferhaus DetailsOb Marienkäfer, Schmetterling, Hummel oder Florfliege. All diese Nützlinge finden in diesem Insektenhaus einen willkommenen Brutplatz und Unterschlupf. Diese Werkpackung ist konzipiert, dass für EINE! der oben angeführten...

... as it will go.  12. Check the quality of the Z surface by test printing. ... 

So, measure twice and print once. In my case, I cured this by simply enlarging the holes with a needle file. But when I came to do this design, I had no idea where the original holes would have been.\r\n\r\nThe rear of the case has positions for two...

I print it with the cut in the bumper, which you can separate carefully with an exacto. Then wrap the bumper around, and trim the plugs as needed until it fits together well. Then I use my soldering iron (set around 3/medium) to heat up the edges...

I printed the part using supports which are only necessary for the corners to the upright face. -- x -- I've also included a camera housing for the rear camera (plus fittings). It is intended that this will be attached to the upper plastic trim...

I encourage experimentation with springs and perhaps with print settings if you know what you're doing to create a blaster fine-tuned to your needs. Grab your Snakethanhas here: https://www.thingiverse.com/thing:3890229 Feedback is very much...

Summary: This is a WIP (work in progress), so don't expect me to answer question about how to print things. If you need different file types let me know and I'll see what I can do. I'm just a hobbyist and I'm always learning. ...

The parts are small so I printed with 100% infill and also used supports for the hex nut holes and the two points that extend out the side of the inside block. Before applying silicone wipe the mould down with dish soap which acts as a separating...

I also added a box for the foreign market tiles for Lancashire.Brass Lancashire BOMItemQtyPurposebrass-lancashire-tile-box.stl4Industry tiles, link tiles, counters, Character tilebrass-lancashire-tile-lid.stl4 brass-lancashire-goods-box.stl1Iron...

These keep everything in place as it should be. If you have any questions then just write to me or comment. And now have fun printing and tinkering. If you like the design, Johannes and I would be very happy to receive a like or a make. Deutsch Ein...

Jam jar, "Bonne Maman", strawberry :-), 77.60 mm outer diameter Please also have a look at my designs on https://www.thingiverse.com/rolfmobil/designs and https://cults3d.com/en/users/rolfmobil/creations under the same username (rolfmobil)... Print...

The interior is covered with heat-reflecting material to avoid heat loss and also to slightly amplify the internal lighting given by a simple LED lamp with an external switch.The filament used is all dark red PETG eSUN brand, printed at 245 ° with...

----------------------------------- What you will need: * Four of the Corner Posts printed in your choice of plastic. * Two strips of polycarbonate strip 1/8" thick, 4" wide, 2 feet long. (Available from McMaster Carr in the USA part number...

The transformer comes in 2 Variants and you could either print it complete or in parts however you want to. If you like my work please consider supporting me on Patreon. Become a Patron! ... Tinkercad link:...

Alternatively, one could print the breasts and make an elastic mold. Step 1 If you look at the breast from the front and imagine a ball in the breast; what diameter would the ball be? <b>Bd= x (mm)</b> If you look at the doll's chest from...