3d printed shadow art

I figured if I ever had a print that needed that additional ~5mm of build volume, then I will deal with new lead screws then. I also already have an Ender 5 Pro with a Dual-Z XL upgrade for a whopping 500mm Z build height, (but still only a 220mm X/Y...

Printing Tips: 30% infill at 50 mm/s If you wish to design your own fraction piece, you’ll need to know the size of a whole. One whole piece is 50mm tall with a diameter of 50mm and an inner diameter of 12.5mm. ...With those measurements, you should be...

It all sounds confusing and over complicated but I can assure you that once the pieces are printed most of the process is fairly straightforward and the other parts to be used can be sourced quite economically. Finally, I will recommend a minimum...

Summary: This is a WIP (work in progress), so don't expect me to answer question about how to print things. If you need different file types let me know and I'll see what I can do. I'm just a hobbyist and I'm always learning. ...

I provided an easy-to-print alignment tool to ensure the heatsink is properly positioned for the cover to fit.\r\n* Duct airflow through the heatsink, don't rely on proper airflow by chance.\r\n* Duct air in one side and out the opposite to maximize...

This design fits on a Prusa i3 MK3 bed.Note: Please only attempt this if you already have some experience with soldering, wiring and electronics in general.Note: Some ATX PSU's may be too deep for this design so if your PSU is over 135mm deep it may...

Please reorient the STL when slicing and printing such that these features face up. ** Note: 2022-02-04 -** the original has been revised to remove any isolated (single square) "towers", called the rev. 2 version. These were found to be weak and...

####Broom stick section: First test the printing tolerances by assembling only the left, right and release part. Insert the clippart of the wheel section. You might have to grind/cut a little bit on the parts for a smooth fit. Push in the Insert...

The filament used is all dark red PETG eSUN brand, printed at 245 ° with bed 80 °, 100% infill to avoid any deformation in the heat. The description is not detailed simply because it is not complicated as a project, certainly a bit of manual...

These models should be also shrank to 80% scale when printing.If "1min-holder-1.stl" is too thin, use "1min-holder-1-thicker.stl" instead.note : Since the number of optional files increase, it might be now confusing to add them here. So please...

My work shop is embarrassingly messy at the moment but I have tested them and they seem to work as intended. Print instructionsThe parts were designed to not need supports you will need to use a knife, razer blade and/or deburring tool to cut out the...

___________ The whole Space Pirates collection comes pre-supported and has been thoroughly print tested. It was first available on our Patreon channel in April 2021. ...Our Patreon creates different collections of sci-fi miniatures each month -...

... done, carefully install your Pi in the bracket, being careful with the pins and make sure all 5 pins go smoothly into the Einsy board. Click the Pi in place so the four printed posts in the corners are flush withe Pi's PCB. ...Snap the cover on.

I had problems with the walls printed vertically. As the plastic wires are laid one on top of the other, the wall is not very strong and it had the tendency with thermal shrinkage to crack. So I added different shaped ribs to see which ones are...

Print instructionsPrinted with PLA plastic at 200 micron and around 7% fill. Mount the two front arms to the main body with a single zip tie. These zip ties should be quite snug, I used pliers. For the rear arm/pivot, first give the hinge slots a...

I printed and tested it with four 10 W blue LEDs (450 nm wavelength), but other types and wavelengths can also be used. Using the 10 W LEDs shown here, an 80 mm fan must be mounted to avoid heating the reaction vials above 30 degrees C. If lower...

I used black to match the container) Magnets (8 total): https://www.kjmagnetics.com/proddetail.asp?prod=DC6PC-BLK Mesh: https://www.amazon.com/gp/product/B07563327H/ref=ppx_yo_dt_b_asin_title_o04 o00_s00?ie=UT F8&psc=1 Thermal Adhesive:...

I tested it by holding the thermistor onto the print-bed as it warmed up to 80c and I could see the fan getting faster and faster - but it was still really quiet. Even at the lowest (and quietest) default speed it puts out a good amount of air and as...

... made it somewhat modular so you could make them taller or shorter. The outer pieces are printed in vase mode and just glued together.I used a 0.8mm nozzle for the outer transparent parts for some additional speed and rigidity.

Tips Be sure your Z axis is positioned so that the endstop is above the level of the print bed before you begin the z probing procedure. You can also use the adjustment for raising the Z axis when probing to help. Finally, I welcome all feedback. It...

UNC 1/4 20 - http://ali.pub/4kpo3g I use high-speed epoxy to fix the screw and handle AB Glue Epoxy - http://ali.pub/4hvg7o The elastic that is yellow in the picture is a TPU filament - http://ali.pub/4kpplb I printed a knob from PLA filament -...

I did just make them to show how the frame look like. Printer settings:Infill- 36% Grid patternPerimeters- 4Hight- 0,2I needed to use XY compensation +0,2 on my printerHAPPY PRINTING!  You need: 4 props where 2 is CCW and 2 is CW12pcs M3x8mm...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

Building Instructions: Assembly: Print all parts first. Put an M3 nut into the opening of the parts called SensorPhotoTransistor and SensorLED. Put these two parts into the water meter main part. Slide rods through holes in the main part and the...

Be sure to print the version appropriate for your application. In order to mount 12mm/14mm wheels to the adapters you first need to install <b>(1) M4x12 or longer socket head screw</b> through the center of the adapter (see pictures for...

------------------------------ PRECAUTION: Après quelques prints, il faudra contrôler que les tensions soit toujours bonnes. Procéder à un ajustement ci nécessaire. ----------------------------- Ce custom est un projet personnel, qui m'a pris...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

A constant current driver operating from 6 V to 15 V should do nicely for powering it directly from the main battery and adding an RC switch to control the light by the transmitter.\r\n\r\nI printed the chassis without supports using PETG and lots of...

Once the bed has been measured, dropping the nozzle to print height will bring the nail back in range of the magnet and retract it to the stowed position. The M5 iron grub screw attracts the magnet back to center and also helps extend and...

Megacity Desert Habitat building for tabletop, expanded by rectangular build option.It contains:WallsRoof tiles with the capssome special sized doorssome basic bits for decorationYou may need to mirror the corner pieces in your slicer to get all...