3d printed samurai miniatures

for both the FGC68, FGC6 and FGC9 in case you don’t want to wait of manual update a already printed shroud just fallow the steps in this video. https://www.youtube.com/watch?v=480iDroe8h0...

Make sure to print the models with minimal infill, - they do need to float after all. There are two main pieces in the kit which we add magnets to: the IgG (antibody) and the Ag (antigen) models and it is*really* important that we insert the magnets...

The box back design for each car is similar in design since I want it to be seen as a set.Print SettingsNozzle size = 0.4 mm (minimum, smaller better)Layer height = 0.2 mmFilament change layer for colours on "300ZXBoxBack":1) Start (Colour of the...

I also don't notice any difference with no polyfill filling at all; so I provided new tops with no basket.* After printing and listening to guppyk2's 4" back horn speaker enclosure, which left me wondering why his design is so popular, I was thinking...

...Both parts are easy to print without support structures. For reinforcement, the part to which the pool pipe is attached with screw clamps has a reinforcement. The hole in the container is approx. 45 mm and was actually drilled for the rubber sleeve.

First, you'll need a 2 gallon bucket (I got one from Home Depot for a few bucks), some M5 screws and some M5 knurled brass threaded inserts (use a soldering iron to install in plastic).I also included a strap mount so I didn't have to carry the ICM...

Only a few parts are needed and it is easy to print, preferably in PETG.You can mount it in different ways, on a tripod, with a table clamp or simply with screws.I would still have to work a little on the software, but it works so far.The stepper...

If you'd like to buy a print of this with metal inserts in the drill holes, please check out my gunbroker page: https://www.gunbroker.com/item/858377600 This is version 1.2 of the C93 paddle release jig I previously released. This updated version...

I figured if I ever had a print that needed that additional ~5mm of build volume, then I will deal with new lead screws then. I also already have an Ender 5 Pro with a Dual-Z XL upgrade for a whopping 500mm Z build height, (but still only a 220mm X/Y...

Please reorient the STL when slicing and printing such that these features face up. ** Note: 2022-02-04 -** the original has been revised to remove any isolated (single square) "towers", called the rev. 2 version. These were found to be weak and...

As for printing requirements, please note that some of the parts in the images do not match their .STL file counterparts due to an error on my part. I uploaded images that demonstrate how to obtain the correct pieces if you encounter any issues. All...

You don't need to print anything to get it working. Another thing I noticed, If you extrude filament on the button and then press again to stop. The hotend does not switch off on this printer. Kids fire hazard if left on Of course if you went...

Lightweight PLA tool is non-conductive, non marking and wont damage your materials if dropped the same as a heavy chunk of aluminum will.  Files Grouped in 5 Categories:MK3S+ Gcode Pre-Sliced - combined : All Files to build everything pre...

**Gravitrax Ball wheel V1.5** - Difference in height 80mm - no support necessary - 2 pressure parts: wheel, pillar - Printing time approx. 5 hours - Select the STL file according to the length of the gearbox, 9.0mm or 12.5mm. - I recommend the...

# Warning **PLEASE PRINT OFF THE SHROUD AND MOCKUP 4010 BLOWER AND CONFIRM FITMENT BEFORE PURCHASING OR MODIFYING ANYTHING! PLEASE POST IN THE COMMENTS IF THIS SHROUD WORKS FOR YOU AND WHAT CARD YOU HAVE INSTALLED** The shroud is designed to sit...

It's a SCAD file, so it's pretty easy to modify (add/change axis button layout).\nNote: The joystick holes look like they won't be holes, I assure you they will be when they're printed.\nParts:1x Adafruit Feather 32u4 Bluefruit LE1x LiPo Battery1x...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

You might want to widen the holes for the screws with a drill (depending on the printing quality you select). 3. Before assembling anything to the case, use a blow torch to warm up the screw brackets and screw in the screws to gently form a thread...

Regarding our parts list, we are utilizing all very common parts and easy to print CAD parts. Our system uses very basic electronics built on a common platform Arduino, but can also utilize any laptop plugged in. Our motors are very common NEMA 17...

####Broom stick section: First test the printing tolerances by assembling only the left, right and release part. Insert the clippart of the wheel section. You might have to grind/cut a little bit on the parts for a smooth fit. Push in the Insert...

Printing Select the vertebrae that you need and import them into your slicer. You will need to apply supports to the bony parts that stick out the back and to the sides. IMPORTANT: Be sure to label the vertebrae as they come off the printer! ...

The transformer comes in 2 Variants and you could either print it complete or in parts however you want to. If you like my work please consider supporting me on Patreon. Become a Patron! ... Tinkercad link:...

I did just make them to show how the frame look like. Printer settings:Infill- 36% Grid patternPerimeters- 4Hight- 0,2I needed to use XY compensation +0,2 on my printerHAPPY PRINTING!  You need: 4 props where 2 is CCW and 2 is CW12pcs M3x8mm...

The FC mount can be printed using either flexi or solid filament, but flexi gives the FC added vibration damping. The motor dampeners are designed to be flexi as well, but they're not essential for the build. The FC of choice cannot use pinned...

The mounting holes are identical between that and the Creality 4.2.7 silent board, which is what I have installed in the first 'final' print. The stock 4010 fan fits upright screwlessly in a mount that holds it to the side of the case, and a buck...

Parts are not oriented for printing. The STEP file is included for easy remixing. I am not an electronics expert but I did the best I could with the design, but still make this at your own risk and let me know if you see something that can be...

TRABAJO EN PROCESOCon este upgrade convertimos cualquier SIGMA a filamento de 1.75, usa extrusores Titan y Hotend V6 de E3D Original.Hemos respetado todos los componentes originales de la impresora, los ventiladores, el termistor y el cartucho...

If you don't use your Western Digital MyPassport Pro all the time, but more like once or twice a year as a backup device for your camera, the battery might be damaged through constant drain of stand-by electronics. My last device died of this since...

Proceeds will be used to purchase printing filament so I can keep testing and designing cool new things that you might find useful. Thank you! Note: Have a look at my other designs, I have some nice sharpening accessories for all your knives...

This is mainly composed by Nitrogen (98%) it is 1.45 times the pressure of that of Earth at the surface, and it is 1.19 times more massive. Titan atmosphere has a climate system, in which methane sublimate and form clouds. It is known that Titan has...