3d printed rc stand

Print the RC car stand rotator pin with a 100% infill rate to guarantee its durability against any stress or strain. Scale it up by 1% for maximum stability and strength. ...If you spot any room for improvement, share your suggestions so I can refine...

RC work stand for 1/10 rc cars, based on a bearing 15x35x11 Base V2 does include shocks support, for shock cylinders up to 16.5 mm external diameter. Holes have been included in case oil is going into the support to ease the evacuation of the oil...

A simple shock stand to build or rebuild your RC shocks. Two different hole sizes fit 1/10 scale (inner) or larger scales (outer). 2 piece print that screws together. ... 3 walls 4 top and bottom layers Pro Tip - spray clear coat on the items to...

BASIC UNADJUSTABLE RC JACK STANDS. TO SIZES I MADE THEM TO FIT TRX-4 AND LIFTED TRX-4. THEY HAVE ZIP TIE HOLE IN THE TOP TO HOLD THEM TO THE AXLE. ...I PRINTED THEM ON FLAT SIDE NO SUPPORTS WERE NEEDED ON MY PRINTER.

Perfect accessory for any RC pit bag - the shock stand! Ideal for storing and organizing your shocks in a plano box while working on them. ...Print two sides and a top for a complete assembly, perfect for 1/10th and 1/8th scale shocks.

I've got a whole collection of RC cars, but not enough stands to go around, so I figured it was high time I built my own. ...The only thing holding me back is whether the printing process will be worth the wait.

I made this RC Plane stand so that i dont have to keep using the kitchen table, and i can work on it without bending over. There are three parts, but you will need to print several of each to complete it. I used 20x20mm aluminium tubing with a length...

I made this RC Plane stand so that i dont have to keep using the kitchen table, and i can work on it without bending over. There are three parts, but you will need to print several of each to complete it. I used 20x20mm aluminium tubing with a length...

This is a two piece RC car stand with a parts tray and holes for building both 1/8 and 1/10 scale shocks. We invite you to try printing it for yourself and letting us know what you'd like to see changed in future revisions. Update 3/24: I've added...

RC stands for Remote Control, and shock absorbers play a crucial role in rebuilding RC shocks. ...Two versions are available, one with 20mm shock holes and another with 18mm shock holes.

I made this RC Plane stand so that i dont have to keep using the kitchen table, and i can work on it without bending over. There are three parts, but you will need to print several of each to complete it. I used 20x20mm aluminium tubing with a length...

This two-piece RC car stand features a parts tray and precision-drilled holes for building both 1/8 and 1/10 scale shocks. We encourage you to print it out for yourself and share your feedback with us on what improvements you'd like to see in future...

I've revised the engine mount for the 3D Printed RC Truck V4 created by MrCrankyface in order to accommodate a 540-class motor.

A miniature, 1:10-scale radio controlled automobile's support structure is what a 1/10 scale RC car stand represents.

The item is a transmitter stand which attaches to your RC transmitter's handle, but be aware the initial version had incorrectly sized handlebar mounts.

RC charger stand designed for ISDT P series of chargers but it will fit almost any other chargers that are more than 62mm wide.

RC tool stand with 7 holes with each 18mm diameter. ... 4 pockets for screws etc Length 200mm, width 80mm, high 25mm.

a support/stand for rc cars of any type. can hold cars up to 1/10 scale and lower. I sized mine down to 90% bc print time. infill 30. lowest res. took my printer approx. 8 hours 35 min. cura said 9 hours 8 min. BE CAREFUL! one of the supports went to...

The RC stand features four notable building holes (accommodating 24mm diameter shocks), strategically positioned at each corner to allow for the addition of rubber grommets (approximately 21mm in diameter, with a depth of approximately 4mm). The RC...

The RC stand with the drawer doesn't have the holes to include rubber grommets due to interference with the shock holes but I would still recommend purchasing rubber grommets from your local hardware store (glue them).The sliding rails for the...

Built on my Prusa i3 MK-3 3D printer, designed to securely hold RC dampers during construction, this tool simplifies the process of filling them with damping fluid and assembling sub-components. Printed using leftover ICE filament PLA Black, it...

This is just a teaser of my last work, a 3D printable 1/5 RC Bike which not only looks quite decent but also works quite decent to be a 3D printed RC vehicle :) See the unveiling of the bike in my "pshycho-lightning" rotary platform:...

# Printing The main frame part of the stand is **240x180mm** so should fit on the bed of most mid size printers, but will be too big for some like the Ender 3 to print in 1 piece. All parts are designed to print without support. These are the...

Boat Stand for the X7 RC Raceboat Check it out at: https://cults3d.com/:1450635 https://youtu.be/LEtQcQhC1KM?feature=shared I made a detailed build guide video, that you can find here: https://youtu.be/9DYU-AvqrMI

Complete drivers stand for RC tracks. For use with a container underneath to be able to lock and keep things safe that you want to keep at the track. ...The ramp is usable for wheelchairs.

A DIY Project: Handcrafted Stand for My Rock Racer Car. ...Fabricated Using 3D Printing Techniques with a Layer Height of 0.4 Millimeters.

A simplistic 3D printed vertical stand for DR ZABER Sentry 2.0

I printed also another Nut as the connection between the thread and the Top cracked over time (my RC car seems to be too heavy). Glued those parts together and used the nut for strength. If I would print it again, I would use 100% infill for the...

The stand is designed to hold a 1/10th scale RC car and features the iconic TLR logo prominently emblazoned on both sides. ...This versatile piece of equipment can serve not only as a display stand but also as a convenient parts tray when additional...

... UNO version. ...In order to control it by RC, I made this stand fixed with nylon standofs on the UNO. ...The RC receiver is hold with zip ties.The Y support holds the 2 antenas at 90°.More info at POLOLU below :https://www.pololu.com/docs/0J57/7.a