3d printed rc plane propeller

The wall mount is designed specifically for leaning planes vertically against the wall, while the ceiling mount is intended for holding the plane by its wing. The ceiling mount has a 4-inch area where it can hold the wing. I used this for both a...

The front two wheel struts come with three clips that should be slid into a cut slot in the bottom of the plane wing so that they can clip onto the struts base. Glue can be used on these joints to keep them in place. These should be fairly strong...

Human: Blending iconic designs from brettbb (rcgroups.com/forums/showpost.php?p=23772243&postcount=1) and Impact RC (rcgroups.com/forums/showpost.php?p=32561744&postcount=383), significant modifications were made to enhance performance. ...Key changes...

Attach this to the wall with 2 command adhesive strips per chock and then mount your planes to the wall to hang them out of the way without pissing off your landlord or significant other (easy removal without damage). Scale it up or down to fit your...

I'm designing glue-in-place hinges with larger knuckles for increased rigidity on RC airplanes. My design features five holes in the leaf to ensure maximum adhesion when using hot glue. ... Two sizes are available: a smaller one measuring half an inch...

This Ski design scales extremely well, printing sets as small as 40% for smaller skis and as large as 130% for 40-60 size planes. The photos show version 2, which lacks the rounded nose. Print at a fill setting of 75 to 100%, with supports, in 0.2...

In this trial, we create 3D-printed wheel covers for a remote control aircraft. The spats accommodate 1.75-inch wheels and utilize PLA+ as the material. ...For Slic3r PE configuration guidance, refer to the accompanying video.

I've custom-built these wheels specifically for my Hall Bulldog Racer plane. They measure 65mm in diameter and 20mm wide, fitting snugly into the wheel pants I designed to match them (check out that other design). ...I fabricated the hub using ABS...

This ambitious undertaking combines state-of-the-art technology and cutting-edge design concepts to create a remarkable experimental plane, one that will test boundaries and pave the way for the next generation of aircraft engineering solutions at...

... urgent signals to servo systems that respond promptly by manipulating control surfaces. In turn, these vital surfaces astutely regulate the plane's orientation in mid-air, expertly adjusting to each delicate movement on the transmitter's joysticks.

This model is designed for crafting a ski plane perfect for soaring through winter skies. The ski features a precision-crafted hole at its center, precisely 3mm in diameter. For the spring component, visit this link: http://ali.pub/33xfos. To...

They represent a 3D model in a format that is optimized for printing, with information about the model's surface geometry and topology. STL files can be imported into various software applications, including 3D modeling programs like Blender or...

Stl files to print parts for hand launched basic plane

This is a simple yet very strong tail skid for Small to Medium sized (1 - 2m or 40" - 70" wingspan) RC aeroplane. It does not have holes for screws as it may be simpler roughen the surface and glue this to your fuselage. There is a tab on the front...

Stand for RC aircraft models weighing up to 1000g. The basis is 5 pcs of aluminum tubes for model up to, tube size 600 g, 12x1.0 mm 800 g, 12x1.5 mm 1000 g, 12x2.0 mm POZ., NAME, ...

This is an untested prototype I made using reference pictures of an existing rc model that has long been discontinued. This model is not ready to fly by anyone other than an advanced pilot and has not been tested. Although a sensible amount of...

Here are the printer settings used: * Material: PLA Plastic * Nozzle Diameter: 0.4mm * Layer height: 0.2mm * Extrusion multiplier: 1.05 (5% more than my usual setting) * Nozzle temperature: 220C (hot for strong layer bonds) * Bed temperature: 40C *...

These are 3d printed ultra lightweight wheels I designed for my Nano Goblin. They work great for my heavy Goblin even as printed however adding some thickness in the slicer can help improve the durability. I included the 60mm version although it...

Modified my Hybrid 3d printed fuselage with foamboard wing and tail to be a tractor style. This cut down on weight and made CG easier. I used less than (2) 20"x30" Readi-board sheets total for the wing/tail components. The fuselage consists of...

3d printed fuselage with foamboard wing and tail. I used (2) 20"x30" Readi-board sheets total. The fuselage consists of individual sides that fit together and are then zip tied in place to make it a modular, robust, and easy to repair design. It...

Split for easy printing. ...Glue together requires no support material.

People are creating models specifically designed to be printed using three-dimensional printers.

Tire printed in TPU, rims in PLA on a Prusa Mini. ...Forgot to resize axle hole on 30mm version.

... Printer of Choice: Da Vinci 1.0 Pro Raft-Free Printing is the Preference. No Rafts are Necessary for Smooth Prints. Supports are Not Required for this Project. Resolution is Set to a High 0.2 mm. ...20% Infill is Optimal for Strength and Lightness.

Modern Airplane Control Station Made in 3D Design Software Crafted by Top-Notch Engineers Control the Skies with Ease The ultimate control system for Remote-Control Airplanes

Stand for RC aircraft models weighing up to 1000g.The basis is 5 pcs (1000mm length) of aluminum tubesfor model up to        tube size600 g                        12x1.0...

... per second, allowing for rapid production without sacrificing quality. Support: No rafts, brims, or support material is necessary for any component, streamlining the printing process. ... Print all airframe components flat on the build plate.

A custom-built holder crafted specifically for 1 millimeter diameter wire, fabricated through precise three-dimensional printing technology at a layer thickness of 0.1 millimeters.

I am simply reusing this existing 3D model, not creating it myself. ...It's a perfect fit for my servo needs, and perhaps others will find it useful for their aerial bombing projects.

Designed by a talented creator and brought to life using the versatile 3D modeling tool Tinkercad, this unique object has its roots in an inspiring project found on Thingiverse under the identifier 2464547.