3d printed rc crawler parts

Basic_Case_Back.stl Basic_Case_Front.stl 16-11-22 New parts Print_17-Spoiler_Bracket+Bumpers.stl Print_18-Spoiler.stl Bug fix, parts were not properly supported on the bed. Print_14-Nuts_Holders.stl 19-09-23 Improvements in some parts Improved...

TUGGY is 25cm long radio controlled 3D printed micro tugboat. TUGGY is easy to print, assemble and sail. TUGGY is a toy, it’s not meant for heavy weight tugging; H-bitts construction is not sturdy enough for the purpose. ...See TUGGY in action UPDATE...

These are all parts I made to make use of original WPL parts that was leftovers from when I upgraded my C24-1 to all metal. https://www.thingiverse.com/thing:4916699 Print order: 1. Axletruss x2 (These will replace the lower trusses on the rear axle...

Here's what you'll need: Frame/braces 4x M3x16 Caphead 6x M4 nut 14x M4x10 Countersunk 2x M4x10 Caphead 5x M4x20 Countersunk (can be replaced with m4x10 Countersunk) 4x M4x20 Caphead Rear suspension/gearbox 2x 70-80mm shocks (I think used "80mm...

Another option is to glue the "Assem1 - Assem_steer-1 steer6-1" parts onto the "Assem1 - Assem_steer-1 steer1-1" part as shown in the assembly diagram. This setup makes it easy to attach the steering module by sliding it into place. The steering...

(new upload because of issues on youtube video) edit : added 3D pdf Printing: Ring - Infil to add weight, supports needed for spade inset. Letter embossing doesn't need it. Spade - Infil to add weight, no supports Letters - Print flat, already...

Before we start... This is my first 3D designed R/C model, It may not looks good enough for most of people but I just happy I can finish this model while learning 3D design and printing. Also I designed this using Tinkercad, sooo no rounded edges (I...

Bottom part of the PCB would slide into lips on the sides of the housing while top is secured with a screw on one side using a small bracket.Printability improvementsMost of the parts have been adjusted for better printability by removing overhangs,...

The tire has a 58mm or 2.25-inch diameter, made from a 12mm foam rubber obtained at "Clark Rubber." It's printed using ABS material and each wheel weighs approximately 12.8 grams.

The parts needed to build a robot include: 5 mm axle, which has been modified with threads. M5 nuts provide the necessary fastening points. 22x8x7 mm bearings enable smooth movement. A salvaged 12v DC motor powers the system. A 3 kg servo motor adds...

You can check out the assembly video for this and the other parts over at my youtube http://www.youtube.com/c/MrCrankyfaceProjects Hardware needed: 4x M3x16 for the housing cap 2x M3 for mounting the motor 2x M3x10 for the bearing cap 1x M3x16-25...

I'd like to show off this brand new body for MrCrankyface's fantastic buggy:\r\nhttps://www.thingiverse.com/thing:3320629\r\nBig thanks go out to him for doing such an incredible job!\r\n\r\nSince I wanted a more aggressive look, I drew inspiration...

... ... Springs for the V3 frame and axles, ment to be printed in PLA, ABS, PETG, Colorfabb XT or similar stiffer plastic. ... Check me out at: Youtube: http://www.youtube.com/c/MrCrankyfaceProjects Instagram: https://www.instagram.com/mr.crankyface/

Front bumper with 10kg servo mount required materials: 12x MR 106 2RS 6x10x3 mm bearings 6mm carbon tube (T-case output axis) square bar 3x3mm (15mm - front axle joint>gear1; the front axle is to be 2mm longer than the bridge housing; rear bridge,...

You can check out the assembly video for this and the other parts over at my youtube http://www.youtube.com/c/MrCrankyfaceProjects You can use the V2 gearbox and cab for this frame but the gearbox will probably skip/break if overloaded, works fine...

1/10 rc crawler beadlock rim in 3 parts

3D Printed parts for the Sherline lathe base modification YouTube Links: Part 1: https://youtu.be/t0aWD35OoZM​​ Part 2: https://youtu.be/8l0fx9UJ1PQ​​ Part 3: https://youtu.be/om9Vjc0SLLE​ Part 4: https://youtu.be/ndekA3CrOCc

these are 3d printed parts for both 3 and 5 inch Karambit quadcopter frames. ... it includes a nano size mount and sma antenna mount.

All of the parts i've 3D printed to make this panel. I've also uploaded the front and back plates that was made in PMMA. ... [my website](https://maxime.aymonin.fr)

Here are 3D printed parts for the AvocadoXL 220, a high-performance racing and freestyle drone. ...Learn more about this exceptional aircraft on our [AvocadoXL 220 Racing Drone product...

3D print two laser cut wood designs

This is the 3D Printed parts of my designed 2" Nano Toothpick. Frame: https://cults3d.com/en/3d-model/various/apus-2-nano-toothpick-frame You can see the complete setup and hardware information in: https://rotorbuilds.com/build/22671 If you liked,...

This is the 3D Printed parts of my designed 4" Toothpick Drone. Frame: https://cults3d.com/en/3d-model/various/apus-4-monster-toothpick-frame You can see the complete setup and hardware information in: https://rotorbuilds.com/build/22644 If you...

This is the 3D Printed parts of my designed 3" SQRT Toothpick Drone. Frame: https://cults3d.com/en/3d-model/various/apus-3-sqrt-toothpick-frame You can see the complete setup and hardware information in: https://rotorbuilds.com/build/22651 If you...

This library of 3D-printed components for foamboard modeling accelerates the exploratory process by allowing large shapes to be quickly created from foam, while smaller, movable parts are 3D-printed ahead of time. Combining these two techniques...

These are additional parts to complete the "3D printed articulating LED lamp" of igorF2. To combine with the others pieces of igorF2. A rotation piece to add another horizontal axis of rotation. ...A solid piece to fix it on a bed head.

This is the 3D Printed parts of my designed 90mm Apus Nano Toothpick Drone. Frame: https://cults3d.com/en/3d-model/various/apus-90mm-nano-toothpick-frame You can see the complete setup and hardware information in: https://rotorbuilds.com/build/23600...

This is the 3D Printed parts of my designed 3" Apus Toothpick Drone. The canopy you cand find in my designs, many options. Frame: https://cults3d.com/en/3d-model/various/apus-3-toothpick-frame You can see the complete setup and hardware information...

This is the 3D Printed parts of my designed 5" Apus Toothpick Drone. The canopy you cand find in my designs, many options. Frame: https://cults3d.com/en/3d-model/various/5-apus-toothpick-drone-frame You can see the complete setup and hardware...

3D Printed Small Parts Organiser:SolidWorks configurable part file (and config instructions) coming soon! This makes it really easy to customize and automatically generate different sized bins all contained IN ONE SINGLE FILE!!These are really easy...