3d printed ps4 controller holder

This set includes all the printed parts which go along the metal plate (source form e.g. <a...

Throw a support on the lower half, then just print the upper and head with brims. Sources: Sherlock Holmes and Dr Watson NPCs by mz4250 https://www.thingiverse.com/thing:3333341 Sherlock Holmes Bust by sylvar75 ...

This is in real time:&nbsp;Design wise, there is not much happening. The box is sized to fit the <a...

... "WITHOUT". Keep in mind that you will loose 1mm of lenght of the screw for the heatbreak fan as shown in the last picture. Print instructionsPrinter Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: 0.2 Infill: 30% Filament: CF-PETG

... any surface with screws or nails. I may explore a way to use these to make a suspended version of the dispenser. Nota3: don't mind the colors. I ran out of black PETG during the print and had to switch to white. ...In the end it's not that bad.

Here's the link to the bearing I created specifically for this remix: https://www.thingiverse.com/thing:4534272 You'll also want to check out my version 1 remix, which should be used in conjunction with this one:...

Summary: My initial build area was around 80mm; a print requiring more height prompted me to design modifications for increased build height. Upon inspecting my printer, I identified areas ripe for improvement. The result is a heightened build area...

I'm looking forward to rolling up to my next conference and busting out a laptop printed into a Pelican case. A full description and build guide can be found at Oceanography for Everyone. Support more projects like this by contributing to my...

Hopefully someone will find it useful (Other peoples prints always look better than mine anyhow!) Sources: Wrapped Egg - Single Extruder by bugman_140https://www.thingiverse.com/thing:2806597Body from Yeti by...

... fan in place of the current IEC inlet. Print Settings Printer Brand: SeeMeCNC Printer: Rostock MAX v2 Rafts: No Supports: No Resolution: 0.3mm Infill: 0.2 Notes: Three perimeters helps ensure the inserts have a good amount of material to bite into!

\r\n\r\nPainting\r\n======\r\nThe marble paint scheme was based on Raffa's [marble painting tutorial](http://massivevoodoo.blogspot.com/2011/06/tutorial-painting-marble.html)\r\n\r\nThe tiles were printed with natural PLA, and then welded to their...

... 2 with the 35mm long 2mm diameter pins. Next start pressing the 42mm long 2mm diameter pins into the holes in the out sides of deckbox part 1, align the latch and finish pressing in the pin. See image below for a section view of the assembled latch.

A height of seven and six-tenths was defined, corresponding directly With an expected final product size, we used primary color red and pattern overlap of eighteen Points precisely measured during each printing pass. As previously discussed above...

Also, don't press too hard, as the frame is brittle and the fan blades could snap off the printed hub. Ask me how I know. Concerning the A4x20 Frame: You need to chop it up, and remove a little over a 1/4 of the frame. It's almost more like 3/8. I...

The wire could get in the way of printing by leaning right towards the bed 2. the sensor no longer felt the movement of the filament because it had to stretch again first. So I thought of attaching it to the extruder to try to remedy the two...

I had to print that after a craftsman tried to shorten the doors length in a rather barbarian style. The door is 83 cm in width - armed with an Ender 3 this translates to 4 parts with 205mm length each, leaving 1 cm uncovered as the door is so...

I managed to get 280mm of print height out of the stock motors, and am using 16" z rods. When assembling the new frame, flip the X axis upside-down and backwards so the POM nuts are at the bottom inside of the arm instead of the top, meaning they...

... to build this wheel. FOR PERSONAL USE ONLY - NON COMMERCIAL - NOT FOR RESALE COPYRIGHT Canary Sim Wheel Designs - ALL RIGHTS RESERVED You cannot sell the digital model, a derivative or adaptation of the model, nor can you sell prints of the model.

IMPORTANT: It is designed to be printed in TPU. I used a TPU with the common 95A durometer. It's meant to be flexible and to protect the frame so it grips in a vise properly without damaging the frame. While I was working on cutting the grooves...

... had to be enlarged to be printable at this size. Resized to 1/3000 scale, the gun barrels and some other details are lost. Printing at larger scales is of course possible, though the lack of detail suited for 1/2400 will become more apparent.

Models include the popular cable chains by johnnniewhiskey over on Thingiverse, a PSU mount for the Ender 3 Pro by Cancerix on Thingiverse, amazing riser feet by thrutheframe over on Thingiverse and also some inspiration by zoly15 here on...

To make one, follow these steps: Select from the available options: * The back angle of your phone: 10 degrees * Whether to counter-sink screw holes in the center plate (screw count, depth and diameter are irrelevant): no * Wall thickness of your...

This housing is **printfriendly** means it is easy to print and needs no support For the powersupply i used this components: Bush 5.5mm x 2.1mm: [Link]https://www.amazon.de/gp/product/B019IFAQ5G/ref=ppx_yo_dt_b_asin_title_o01_s01?ie=UTF8&psc=1...

The drawer handle is designed so that the LCD Knob can still be rotated when installed on a drawer or cabinet and provides tactile feedback mimicking the feel of the rotary encoder found on Prusa printers.The drawer handle consists of three parts:...

Then, for now, the program just prints out that z height planes as a layer text to the output file to show that we have at least gotten this far with the program. USAGE: slicer.pl input_file.stl output_file.txt I included an STL model because it...

After clicking print, you'll be prompted to open the new tab and save the image or discard it, whichever you prefer. In order to proceed further, select each individual render starting from the deepest (-3900) layer all the way up until (-2900),...

I borrowed the mount from MMendel and redesigned the blower to give more print cooling and hold an induction sensor. Also, if you change the hotend, you will need to run PID tuning otherwise the hotend won't get to temperature. And the induction...

It has been a while since I printed and fitted it to my printer, so I cant exactly remember if I needed extra fasteners, I know for Shure I needed 10x 3mm plastic screws for the bottom panels, and 4x M2.5x6 for the raspberry pi, but I think that's...

print a large end and glue it to the screw head. I'm attaching this as a .STEP file... I'd rather you take a look at this F360, Freecad, etc... it works great as is, but I'd love to get some feedback. I'm open for any suggestions on...

You can print a lot of things, but not everything. Even though I had to learn this the hard way it was still very interesting to do and I had a lot of fun designing and testing it. Also it was interesting to see the 300 m target with 24x. With...