3d printed ps4 controller holder

Insert that STL into your printer, as it takes longer to print than you need to set up the pi&ssd ##2. Just follow [these instructions](https://www.raspberrypi.org/forums/viewtopic.php?t=44177). It doesn't take as long as *paulv* wrote in 2013.... I...

I configured the K-factor of linear advance feature to 0 in firmware, and it's necessary to configure it before every print in start G-code using a value of 0.7. I'm using this start G-code in Cura: M140 S[first_layer_bed_temperature] ; set bed...

Every glance at this work of art will make your eyes light up with admiration.Printed in PLA or PETG, the robust material ensures long-lasting stability, giving your board a firm hold while creating a harmonious connection between window and...

Instructions 1 - Print both halfs 2 - Insert desired weight in lead into the pockets. weight in the back will make the lure running shallower, weight in the front will let it run deeper 3 - cut a toothpick and use 2 sections where it doesnt taper...

Edit 27-10-2018: added the Fusion 360 original This is a second, improved version of http://www.thingiverse.com/thing:1526752 Detachable top part - easyer for transport RGB Color LED for status More sturdy frame Improved software Smaller electronics...

I printed the coupling with TPU and fits onto the gear wheel of the stepper motor and onto the self-locking nut M8. The stepper motor probably comes from a Canon inkjet printer. ... Are needed: 1x stepper motor 35 mm SMJ35-4831-B or identical 3x...

Since the housing is hollow when printed with infill, it might tend to swim. So I recommend to drill some small holes in the outer shell to use the infill space for ballast water... The shaft should be 10mm in diameter and ca. 80mm long and made...

Geoff Gregor's notes on his R2a modification state: "Summary: Nut pocket slightly bigger, screw head pocket much smaller, less damage, no more slop, screw stays aligned for happy printing (hopefully)." After struggling with a squeaking belt on my...

I like to create separate arc bodies that can be printed in a different color as a nice accent there sometimes. ...I tried Glow in the Dark filament for those the other day which turned out pretty well.&nbsp;</p><p>--------------------</p><p>Sidenote: I...

To achieve this, you can adjust your printer using the following template: https://www.thingiverse.com/thing:5413456 It allows you to adjust the feed rate specific to your filament to obtain precision of the order of a hundredth of a millimeter,...

Print 2 of each half-wheel and use clamps or a hammer and a wood block or press/drill press to seat the bearings in place. Next, place one pair of the half-wheels around the tire, using bolts to align the holes. Use clamps to hold the two halves...

Once you've printed out this part, and optionally Piercets external tensioning parts, remove the current idler and take the 608ZZ bearings out. Add the additional 608ZZ bearing, put a washer between each bearing and on the top and the bottom of the...

Files with FDM are modified to print better with filament printers Set 04 - Generals and Staff - FM Bluecher in several poses, plus a few generals and other staff officers Set 05 - Misc. Officers - Many Reserve and Landwehr officers wore regulation...

How to make You can print all parts without support. Place on the build table as supplied. Circuitry is exactly as same as former thing named "Minimal Mechanical Digital Clock with Network Time Acquisition", https://www.thingiverse.com/thing:4931539...

I have modified this with an easier to print screw ring with nubs for easy grasping and have uploaded 2 versions of the screw ring and insert one is scaled down to 99% so if the full size one is too tight the scaled down version should fit easier. I...

Each side will hold a maximum of about 400 pages, making an up-to-800-page book when printed double-sided. I use this jig to bind both my PDFs and compilations of my children's artwork into neat archives for later enjoyment. We've probably compiled...

:) My fav PLA on Amazon Italy: Tianse PLA Sunlu PLA+ GEETECH PLA My fav Resin on Amazon Italy: Elegoo ABS Anycubic eSUN Print Settings Printer: Alfawise U30 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Tianse PLA White Category:...

Print the "_withbutton" versions of the bezel and frame, as well as the button cap. Insert something squishy (o-ring, piece of foam, rubber band, etc.) between the pushbutton and the button cap. A Raspberry Pi Zero W could be used instead of the...

ive not printed these yet to try them but they should be the same as the ones im using now just being round instead of square. thought id update this with them incase someone who wants to try this would rather have the round instead of the square. ...

The design consists of 3 parts : the base (about 4 hours) - 12% density zig zag support and 10% gyroid infill the spindle (about 4 hours) the screw (about 20 minutes) Note : spindle has been printed with different support angle. The outer shell is...

I added a ziptie location for the cables (break off the designed-in support), modified a ton of tolerances, got the fan ducts adjusted to the proper height with the nozzle, made a permanent BLTouch mount, embossed "CR-10S Pro V2" and "Micro Swiss...

I would like to change the base and top part for reducing the print time. Edit your own version using Tinkercad: https://www.tinkercad.com/things/bshg0Q4fTUs-sputnik-pieper-modell-remake To build this project, you will need: * A PCB, which could be...

12mm tubes have been tested, and test prints are being done with PLA. The fitment of the connectors may not be the same with different plastic combinations. Ideas for improvement include using TS Twist Plug to stop any ports up that aren't being...

I think the rear is further apart, but you'll figure it out quickly when you try to attach to base.Use M6x35mm screws and M6 washer to attach top-cross bar assembly to the base!&nbsp;Other Remarks:Printed with Carbon Fiber PETG.Infill at 40%Used with...

This is a little bit tricky as you may not touch the PLA printed support with the hot solder iron, and the space through the spokes of the outer support rings is quite limited. At last, mount the Nd-bearing magnets onto the axis. Use the hülse.stl...

You’ll need to print the following and its best to fit in this order: If running the V6/Dragon carriage mod then fit the cable retainer and cable into it first, skip this step if you’re not. I’ve included a few options you could use: Cable...

If you print it to the right diameter, you might not need to drill it out, but getting an airtight seal can be frustrating. The Solidworks file is included if you want to adjust the hole size to eliminate the drilling process or use a different...

It is the low-poly and easy to print version of ionic, doric and corinthian columns. Doric and corinthian columns are supportless, only ionic column has some easy to clean supports. Just like chess knight is not photorealistic and just symbolic, goal...

The 18 to 22 pipe fitting could be removed This plate could then be copper plated with this technics : https://www.thingiverse.com/thing:1661301 If you have any design to share I would be glad to offer at least the binary codes of the ESP32 and the...

Take care to ensure the Adapter port with the wires has been sanded to remove sharp edges & serrations from the printing process. Slide the Adapter over the motor and secure with a 2.5 to 3.6mm wide zip tie. A pair of pliers will help to pull the zip...