3d printed pmag

This is a work in progress pmag for the ar10 series of rifles (airsoft) currently the way to secure the inner midcap mech is to slide it into the pmag shell and once aligned, it should be super glued in place, then slide the baseplate on this is...

This is a work in progress pmag for the ar10 series of rifles (airsoft) currently the way to secure the inner midcap mech is to slide it into the pmag shell and once aligned, it should be super glued in place, then slide the baseplate on this is...

This is a work in progress pmag for the ar10 series of rifles (airsoft) currently the way to secure the inner midcap mech is to slide it into the pmag shell and once aligned, it should be super glued in place, then slide the baseplate on this is...

I use a .2 layer height, 100% infill, concentric walls and infill or just set the wall numbers high enough not to have infill. The pull I print at .2 layer height, 50% infill and tree supports. ...I'm still learning the best way to print TPU with...

I've got a deal that's too good to pass up on pmags with the big igloo design, but they're selling for $30 - a price I just can't bring myself to pay, especially since every single one is a 30-rounder and I'm stuck in California. So, here's the deal:...

I'm seeing pmags for sale with the big igloo design and didn't want to spend thirty dollars on a mag (also they're all 30 rounders and I'm in California). So here you go. Make as many big igloo pmags as you like for only one dollar. All I had when I...

The magnets are found on Amazon. Fully charged magazines are easily held in place with these magnets.Meant for Gen 2 PMags but Hexmags also fit in the reverse orientation. MFT and THRIL mags do not fit these racks, nor will any magazine that...

This is a edit of https://www.thingiverse.com/thing:736141 I needed a Pmag holder that can hold loaded mags for my vault. This is reinforced and can hold loaded mags without sagging. I'm also posting a 300 blackout version . . ....

I'm offering custom-made 30-round PMAGs with the large igloo design, a deal that's hard to pass up considering you can get one for just $1. I used flex seal for my initial test, but I've come to realize that thinner sprays will yield better results.

I created this to organize my Gen2 and Gen3 PMAGs in my safe. It holds them in an upright position with very little wobble. The pins to lock them together aren't quite right yet, so this is an early version. ... Updated the design to be a little...

I designed a custom floorplate for an airsoft magazine, taking it from concept to reality with the aid of 3D printing technology. ...The vertical supports, strategically placed on the flat end, ensured stability and structural integrity throughout the...

I printed most of my magazines with carbon PETG at a layer height of 0.15 and an infill of 30%. It's easy to put them on, but tricky to remove because the part you grab is in the way, so I designed a tool that helps push down the spring detent...

I update that model to be a little thicker on the ears as well as adding some 45 degree chamfers so it would print with less supports required. I also updated the dimensions a tad to be a better fitment overall. ... Recommend printing with supports in...

I update that model to be a little thicker on the ears as well as adding some 45 degree chamfers so it would print with less supports required. I also updated the dimensions a tad to be a better fitment overall. ...Recommend printing with supports in...

... on the handguard. A buddy of mine needs the Short version because of the SBR length. They are about a 2 degree difference. I also added a little curve on the inside of the monopod on the Long version for even easier identification after printing.

... airsoft gun, this is a mag shell for his tec 9 that i have been authorized to post. ... Igniz's tec 9: https://cults3d.com/en/3d-model/gadget/tec-9-kek-9-6mm-airsoft-gun-body-kit-for-standard-ak-components Igniz's Discord: https://discord.gg/DPYEGvH

... installed on the mag. It wastes a lot of filament for the supports, but I've found if you print on a 45° angle with the bottom of the cover facing down, it results in a stronger print. ...I haven't had any layer line failures with this method yet.

... sprays will turn out better. I'm going to be picking up some white cerakoat and testing it.Print SettingsPrinter Brand:CrealityPrinter: Ender 3Rafts:NoSupports: NoResolution:.02Infill: 100Filament: Hatchbox PLA Black Notes: lay flat   Category: DIY

... is an entry into the Vectary Design Competition sponsored by MakeX. ...It was crafted using VECTARY - the free, online 3D modeling platform. The model was then brought to life through 3D printing and transformed into a mold for a metal casting process.

A customized version of the design is available at http://www.thingiverse.com/apps/customizer/run?thing_id=52734 with specifications including font thickness of 5.5, stick thickness of 3, no hole radius, a font named "write/Letters.dxf", a message...

The specifications for this design include disabling the hole, utilizing base style 2, a thickness of 15, extruder positions of 54 and 68 in y and x directions respectively, output style 2, text saying "3D PRINTED", text spacing of 10, a style of 1,...

Created by Customizer - Create custom versions of http://www.thingiverse.com/thing:749887 Using the options: - wall thickness is set to 1 - base thickness is set to 0.1 percent - font name used is Holtwood One SC - text string is customized with 3d...

http://www.thingiverse.com/apps/customizer/run?thing_id=518217 Instructions Using the following settings: Font - Orbital Writing in Orbitron Style, Optimized for High-Quality Output Box Depth - Elevated to 40mm for Enhanced Durability and Structural...

This is curved text, for display or desk nameplate. ...The scad should be easy enough to move, twist, or size to copy and paste it to other things. I'm printing one as we speak. ...I will make changes, if it turns ugly.

Magazine holder for AR (PMag Gen 2)

PMAG GL9 extension. Fits Magpul PMAG. ... Adds four 9mm rounds to stock mag, with stock internals.

for Print settings, please consult the Hochul mags uploaded on odysea by The Gatalog (https://odysee.com/@TheGatalog-PrintableMagazines:6/Hochul_Mag_AR15:f) These are compatible with Gen 3 PMAGs. ...There are 3 lengths, availiable, short, meduim and...

... ...To assemble, simply install one #4-40 x 1" Socket Head Cap Screw to firmly lock the device around the magazine. Optimized for printing with ABS plastic, this design allows clips to stand upright without requiring support during the printing process.

These Extensions are remixes of the Hochul-mags Extensions, designed for areas, where you are limited to 10 round magazines, but want the better ergonomics of a standart capacity magazines.for Print settings, please consult the Hochul mags uploaded...

... here. Recommend supports touching bed and infill of 20%. You will want to test fit and verify the total capacity once you print this out, I cannot guarantee that your tolerances or material shrinkage will keep this at a 10 round capacity.