3d printed phone case template

The holes for the banana plugs and the iron holder are not included in the file but can be easily drilled after the print is complete. I did not take photos of the inside because it is pretty crowded with wires; however, if anyone is interested, I...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   ...

I printed all the parts with PETG, 5 perimeters, 40% Infill. The EndPin for the optical endstop must be black (or painted with a marker). They will require support in places where there are nuts or countersunked holes. I have included a small test...

Print quality is good, and I'll try a benchy and ghosting test later. The diameter of the sticks is 7.2 mm, but sticks with a diameter of 11 mm can also be used - they're almost three times as stiff in theory. 7 mm glue-sticks are fairly cheap, and...

to the picture).4) Zip-tie, screw or stick (doublesided tape) the gimbal controller to your plate.be careful that the m2 screw in the middle of the plate doesn't short out the controller!5) If you want print out this nice cover:...

... a small riser to get my cheap red dot (https://www.amazon.com/dp/B00A36MKUO) to the correct height for a good cheek weld on the taller dust cover. I recommend 30% infill and PETG for printing. ...If you have any issues or remix it, let me know!

... (about 7-8 cm each) some soldering skills. **Edit:** Added original adapter battery rail ### Print Settings --------------------------------------- **Printer:** Anet A8 **Supports:** Not required **Resolution:** 0.2 0.32 for the lid **Infill:** 20

... amélioré : plus esthétique (et d’autres éditions spéciales;) ), système d’éclairage led, etc. Pour suivre ces améliorations, n’hésiter pas à vous abonner a ma page Thingiverse et Facebook : https://www.facebook.com/waikikiprod Bon print à tous !

If you make one or have improvements, please post. Print instructionsCategory: Costume Summary Here is my third version of a costume prop for Tom Clancy's The Division video game. It's some kind of shoulder beacon / gizmo that all the characters...

I calculated that the production didn't justify the cost of printing the 402 parts for the space rocket and made the decision to have them laser cut out of plexiglass. Then, I ordered all the straight parts (1HSP to 5HSP) to be cut out of plexiglass...

## My printing set up Sovol SV06, 0.6mm nozzle, 0.4mm layer height. 4 perimeters, 10% gyroid infill. Snug or organic/tree supports (snug gave me slightly better quality, organic was much easier to remove) and overhang threshold at 30 degrees. ...

The whole size is the only change.3MF-  Two Colored: If you can print in multiple colors, use the 3mf files, which also use 6x2mm magnets.Printer SettingsLayer height - As low as you can go. I used 80 microns.Infill - It doesn't matter, I believe I...

Instructions: Print the cover/faceplate, body, and screw jig.. in the body, insert the 2x, m3, heat set inserts, in the 2 ears from the inside of the body, so the screws would be trying to pull the insert all the way through, instead of back...

If you fix it for print, create a Remix, or send me a new model for re-upload, please do. A succubus is a demon in female form, or supernatural entity in folklore (traced back to medieval legend), that appears in dreams and takes the form of a woman...

Textured PEI is better than smooth one.You can buy segment numbers and comma with stands (and this printed parts too) on my e-shop www.vokolo.cz, for Czech and Slovakia customers only. From other countries please send me message, I can send to EU, UK...

Assemble the printed parts by snapping the front and back onto the top/sides piece, making sure that the LED goes into its little side hole and the Pi camera cable does not obscure the HDMI opening in the top. 3. Plug the USB DIY connector into the...

This sculpture combines elements from this image and the side view in this article. This sculpture was created with Sculptris, and I'm eager to hear how it prints out or any feedback on improving its printability. These tiny hominins were discovered...

I speak up now only for the next generation of silent sufferers, which from what I've witnessed from the inside is the 'True Normal'.) I kind of feel like printing mostly Sixteenth and Eighth notes and rests, to suggest high energy and rhythmic...

All other cars use the same wheel. Since I dont have an existing Brio or Ikea train set, I printed all my tracks from the following project using a -7.4 mm Z offset in my slicer, so that the tracks were thin (no need to waste filament/time making...

Using an M3 tapered tap, I found it was relatively easy to slowly do this with no pre-drilling.The thread will, of course, not be complete and that is why a long screw is used in fixing.Assembly:Two M3 nuts should be pressed into the back of the...

You’ll need to print the following and its best to fit in this order: If running the V6/Dragon carriage mod then fit the cable retainer and cable into it first, skip this step if you’re not. I’ve included a few options you could use: Cable retainer...

For this project, you will need: • 1/8" Clear acrylic • 1/8" white acrylic • Spray paint • Methylene Chloride Cord or chain Print Settings Printer: Trotec Speedy 300 How I Designed This Step 1: Laying out the letters To produce a high-quality...

# Print Instructions: Be sure to use supports for the wall pin and the gun holder. Take care to clean the supports and leave a smooth finish on the gun holder. I set this up so the gun points to the left to hide the screw holes. If you want to...

This is basically the **Customizable Better Temperature Tower** by *kmsd3d* including: - several pre-rendered stl files for various filament types - a list of layer change settings - the original customizable OpenSCAD file - an Python3-tool to create...

Printed all the parts with PCTG. Geänderte und verwendete Dinge aus: Changed and used things from: Adjustable LED Strip Backets https://www.thingiverse.com/thing:2207879 40mm Fan turbine cover with Dust Filter ...

They print at slightly hotter temperatures. Also, consider flexible TPU filament for the lid bumpers and the washers. The resilient material offers a quieter closure on the lid, and gives a bit of conformance on the nut tightening. The bumpers...

A Dremel or lighter can probably fix it if you've already printed, but there's a new version up too. Also added new versions of both frames that have a cut-out piece for a wire cover. You screw that into the bottom and it should protect those pesky...

Required components: 1 x high-torque geared motor (I used 5 rpm, it's slow but will never have problems with moving my blinds) 1 x L298N motor controller 1 x ESP8266 (I used a Wemos D1 Mini) 1 x micro-switch A couple of 3mm screws for the motor and...

It's not intended to be printed (model was taken from McMaster Carr). ... Side Note: If you're wondering what the vise base thing is with all the alligator clips, etc., it's an awesome tool from Hobby Creek:...

During printing the holes can sometimes be narrower. Therefore it may be necessary to drill them out. Take one thread and make a multiple knot at one end and then pull the thread through one hole. Place the top ring with the bottom side facing up. At...