3d printed mtg life counter

I did just make them to show how the frame look like. Printer settings:Infill- 36% Grid patternPerimeters- 4Hight- 0,2I needed to use XY compensation +0,2 on my printerHAPPY PRINTING!  You need: 4 props where 2 is CCW and 2 is CW12pcs M3x8mm...

The box back design for each car is similar in design since I want it to be seen as a set.Print SettingsNozzle size = 0.4 mm (minimum, smaller better)Layer height = 0.2 mmFilament change layer for colours on "300ZXBoxBack":1) Start (Colour of the...

The drawer should now slide into place.• I guess you're all done unless you want to make more drawers :)Installing Drawers under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will...

Other Notes: I printed these on a Super Racer @ 100% infill, 100m/s 210/60deg. I wanted them solid to transfer as much of the vibration as possible through to the pedal. Probably doesn't need to be that solid but they still took less than 1 hour for...

There are two methods you can use, either print up a new modified WhiskerScar with the rib cut out for a 19 mm OD and 16mm ID 1.7 mm thickness o ring (or some close equivalent) or you can use electrical or masking tape on an existing Whisker scar...

There are also two variants of each model - one "basic" variant, and one variant that has been slightly altered to suit printing at 28mm scale. You will find all 28mm variants in the zip archive named "28mm versions" included in the purchase. All...

... It was only off .13mm (.0051 inches) at the most, but not really an issue if you have printed the parts already. Here is very short video of this machine working. https://youtu.be/HgV3grxkY44 I also added optional **CantileverStablizer.stl**.

Also, the "spikes" on the gripper didn't print well and had layer separation. The gripper is the part that connects onto the end core which pulls out. It uses a screw to tighten it. There are 2 gripper versions based on if you have the normal...

Print at 0.4mm nozzle, 0.2mm layers, otherwise all design tolerances will be wrong. It is a good idea (maybe essential) to specify 0.4mm wide outer perimeters in your slicer. PLA works fine. Supports are required, but only because of one very...

**Gravitrax Ball wheel V1.5** - Difference in height 80mm - no support necessary - 2 pressure parts: wheel, pillar - Printing time approx. 5 hours - Select the STL file according to the length of the gearbox, 9.0mm or 12.5mm. - I recommend the...

For a complete listing of character maps, do a simple search for "ASCII character map" Print instructionsOnly requirements are an Arduino Pro Micro (I used a clone board from Amazon -- HiLetgo 3pcs Pro Micro Atmega32U4 5V 16MHz) You will also need...

The secondary goal was to keep it simple and quick to print.The tripod consists of the following components:Tripod Head: Featuring fixed holes positioned at 20 degrees from the central axis.Telescopic Legs: Made from 6mm outer diameter and 4mm inner...

Here's what you need: * 6m GT2 with 2mm pitch belts * 1x 1040mm closed-loop belt (520mm perimeter) used for dual Z * 2 x 200mm closed-loop belts (100mm perimeter) * 4 x 20-tooth idler pulley with 5mm inside * 2 x 20-toothless idler pulley with 5mm...

The first level is composed of 5 components of which each part has fittings arranged differently so as to allow easy assembly, parts from 1 to 4 are numbered the fifth central fitting part to be assembled last, once the prints are completed, proceed...

Shoulders and Forearms (https://www.aguilarworkshop.com/product-page/odst-battle-armor-arms) Armored Plate Carrier (https://www.aguilarworkshop.com/product-page/odst-battle-armor-armored-plate-carrier) Utility Belt/Waist...

Be sure to print the version appropriate for your application. In order to mount 12mm/14mm wheels to the adapters you first need to install <b>(1) M4x12 or longer socket head screw</b> through the center of the adapter (see pictures for...

Then print the 2 models and install them on the printer. For the sensor set it in retract mode and touch the nozzle and the bed. Then place the 2 mm (approx.) allen wrench supplied with the printer between the tip of the sensor and the bed and screw...

I've printed a half-dozen of ‘em and they’re smooth as butter. The M10 coupler will screw into the Bowden tap nice and easy by hand.</p><h4><strong>Instructions&nbsp;</strong></h4><p>The pictures should be easy enough to follow but just in case here...

A constant current driver operating from 6 V to 15 V should do nicely for powering it directly from the main battery and adding an RC switch to control the light by the transmitter.\r\n\r\nI printed the chassis without supports using PETG and lots of...

Using it I created 12v powered Media centre with LibreElec running KODI so that I could watch TV-shows or movies in my RV without having to bring disks with me or have access to streaming services. I load the HD up with my ripped DVD's and then just...

I printed the part using supports which are only necessary for the corners to the upright face. -- x -- I've also included a camera housing for the rear camera (plus fittings). It is intended that this will be attached to the upper plastic trim...

このモデルは以下のモデルの自己Remixとなっています。 CE32A 1" Speaker Driver Enclosure PAM8403-based Tiny Audio Amplifier Board Adafruit Stereo 3.7W Class D Audio Amplifier MAX98306 Enclosure Adafruit Breadboard Friendly 3.5mm Stereo Headphone Jack Enclosure Adafruit USB...

...There is a preview .stl--nothing to print yet! Updated with v2 parts 09/21/2017: Added longer V2 parts that use two screws for better clamp support, similar to a woodworkers clamp. If you are shooting for light and cheap stick with the V1 clamps.

If your looking for the original look the v1.0 release at my Github repository: https://github.com/kellyegan/Arduino-Mounting-OpenSCAD-Library The library uses tbuser's pin library for the pin mounts: http://www.thingiverse.com/thing:10541 There are...

The drawer should now slide into place.• I guess you're all done unless you want to make more drawers :)Installing Drawers under each other• This is the same process as above but instead of mounting the "Rail Lock" into the nut on the rail you will...

... post 'em! Really! Take a cameraphone photo with your dope color matched mount in all its glory and show it off! Plus it really helps get this design out there to the world.Want a generic GoPro mount version?I got you covered, check out this design.

Added a photo showing the Endstop in fluorescent green filament. Print Settings Printer: Woodstock Delta Rafts: No Resolution: 0.2mm Infill: 25% Gyroid Filament: Generic PLA, PETG Any Notes: Orientation is often not correct, you will most likely...

Ideal material: alveolar plastic thickness ~ 2mm (from supermarket advertising panels) Flexible plastic mesh 5x5mm: cut-out size 430 x 220 mm Diameter of the holes: Passage Bees + Hornets: Ø8 to 9 mm Passage Bees only: Ø5 to 6 mm Print the 3...

There is a new version of this carriage at https://www.thingiverse.com/thing:3615464 AND an even newer one at https://www.thingiverse.com/thing:3688067 ** ** I'd recommend that newest version instead for better rigidity and simpler printing and...

I also don't notice any difference with no polyfill filling at all; so I provided new tops with no basket.* After printing and listening to guppyk2's 4" back horn speaker enclosure, which left me wondering why his design is so popular, I was thinking...