3d printed mouse trap

This is my over complicated / over engineered solution to prevent humidity from ruining my filament while it prints in my garage. The spool sits on the rollers inside the container and feeds out a tube on the bottom. The roller assembly has an...

The screws go through the mounts (print off Y Rail Mount A and B twice and bolt C onto the back of each) and the belt is zip tied to this. My tests show good hold and adjustability. There are also some for the X rail but they involve a new design for...

#### Broom Stick Section: First, test the printing tolerances by assembling only the left, right, and release parts. Insert the clippart of the wheel section. You might need to grind or cut a little bit on the clippart to make it fit. Now repeat the...

... It was only off .13mm (.0051 inches) at the most, but not really an issue if you have printed the parts already. Here is very short video of this machine working. https://youtu.be/HgV3grxkY44 I also added optional **CantileverStablizer.stl**.

Two versions available: > 1.3.1 Wheel + 2.2 Distance: Can be printed without support and must then be glued together > 1.3.2 Wheel: All in all, but needs support (for Overhang Angle 89 °) The axles are small and the rims fit exactly, so make sure...

The first level is composed of 5 components of which each part has fittings arranged differently so as to allow easy assembly, parts from 1 to 4 are numbered the fifth central fitting part to be assembled last, once the prints are completed, proceed...

The alternative file is what is in some of my first renders and does look cool, but they are often annoying to print and glue on the vehicle so adding them is up to you. Size of model when completed 165mm length, 90mm width, 68mm high. ...Instructions...

... in Tinkercad. Some of the screen shots show artifacts on the models from the edits, but do not show up on the prints themselves.Also if anyone has a spare Ender 5 carriage plate, I would happily take it off your hands (message me with price).

:) My fav PLA on Amazon Italy: Tianse PLA Sunlu PLA+ JAYO PLA+ My fav Resin on Amazon Italy: Elegoo ABS Anycubic NOVA3D Rapid Resin Print Settings Printer: Alfawise U30 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Tianse PLA White...

It should be fully rules complaint but check dimensions before using this design.Note: At time of upload, the design has not been tested in competition and has no guarantee of performance.Note: The pictures included with this design show a Launcher...

... professionally done and designed to remove beautifully (provided you have dialled in your printer settings). They are guaranteed to give you one of the best printing experiences you've ever had! Are we allowed to use the term "printgasm"?! ...:-)

The box back design for each car is similar in design since I want it to be seen as a set.Print SettingsNozzle size = 0.4 mm (minimum, smaller better)Layer height = 0.2 mmFilament change layer for colours on "300ZXBoxBack":1) Start (Colour of the...

Print Settings Nozzle size = 0.4 mm (minimum, smaller better) Layer height = 0.2 mm Filament change layer for colours on "300ZXBoxBack": 1) Start (Colour of the background, mine is in white) 2) Layer 14 (All logos outline and "Twin Turbo" letters...

6 is a hinged version, you need to print 3 of the hinges and 2 of the shafts.If you like my work please consider supporting me on Patreon.Become a Patron!Some of my other designs:https://www.thingiverse.com/thing:4654378 - Rivet Cutting...

Once the bed has been measured, dropping the nozzle to print height will bring the nail back in range of the magnet and retract it to the stowed position. The M5 iron grub screw attracts the magnet back to center and also helps extend and strengthen...

You don't need to print anything to get it working. Another thing I noticed, If you extrude filament on the button and then press again to stop. The hotend does not switch off on this printer. Kids fire hazard if left on Of course if you went...

It is represented the inner part of the cold region of the disk, which is about the diameter of Pluto. The "middle" cold disk goes almost as wide as Saturn. The disk is actually a lot less thicker than this, but it is was made like that in order to...

------------------------------ PRECAUTION: Après quelques prints, il faudra contrôler que les tensions soit toujours bonnes. Procéder à un ajustement ci nécessaire. ----------------------------- Ce custom est un projet personnel, qui m'a pris...

Also (constructive) criticism or exchange of experiences is welcome! Please also have a look at my designs on https://www.thingiverse.com/rolfmobil/designs and https://cults3d.com/en/users/rolfmobil/creations. under the same username (rolfmobil)......

No print support needed!This is an as-is project, will not improve it any further.It works great, cooling is better than stock, it's solidly attachedonly downside is limited visibility on the nozzle.This is a bit weird to setup due to the metal plate...

As for printing requirements, please note that some of the parts in the images do not match their .STL file counterparts due to an error on my part. I uploaded images that demonstrate how to obtain the correct pieces if you encounter any issues. All...

Because of the height of the box, the width of non-snug sleeves, and the text size required to come out visible without a .25mm nozzle (and by Thor, I would not want to print all these separators with that!) it became necessary to make the dividers...

Here is an example of how you could extract and print these lists in a Python script: ```python import json # Assuming that the provided JSON string is in a variable called 'json_str' json_str =...

I need my printer to be able to use stronger higher temp materials and be able to print delicate single perimeter components for the wings and fuselage. I decided a direct drive upgrade would be a good upgrade to provide better performance and higher...

Summary: This is a WIP (work in progress), so don't expect me to answer question about how to print things. If you need different file types let me know and I'll see what I can do. I'm just a hobbyist and I'm always learning. ...

Little material and time is required for printing. The "screws" and "nuts" can be pushed onto one another with a little force, the components are too small for a screw connection. I use the fan on the desk and another one to circulate air in a mold...

Ein Adapter Um 4x18650 Zellen anstelle von 2 Parallel zu Laden / Analysieren. Nur für den adapter wird stützmaterial benötigt... Die Sicherheitsbegrenzung für die Ladekapazität muss allerdings deaktiviert werden, da in diesen Slots max 2000mAh...

So I like to print a test piece before committing to anything big or sensitive. I find that making a piece of OS-Railway track using whatever filament is intended for the project is usually enough to warm up the bed and predict if the printer can be...

(I use 4 x 25mm M2 screws) For mountig my rx and vtx, i printed 1 x vtx_base.stl which fits onto the fc stack. For the rectangle standoffs you need 2 screws and 2 nuts to fix it. These standoffs are inteded to use at the left, right and rear side...

**Please buy using the following links to support my creations (doesn't cost you anything):** [Good quality E3D V6 clone][1] [1]: https://s.click.aliexpress.com/e/_AqHeoo [Good quality E3D V6 clone copper version][2] [2]:...