3d printed motorcycle hand guard

If your looking for the original look the v1.0 release at my Github repository: https://github.com/kellyegan/Arduino-Mounting-OpenSCAD-Library The library uses tbuser's pin library for the pin mounts: http://www.thingiverse.com/thing:10541 There are...

There is, however, a fair amount of stuff to print for this modular insert and some optional parts. I will Identify the stuff below that is optional. To start, take everything out of the original base game box, including the manuals, player HP/RAD...

This is my over complicated / over engineered solution to prevent humidity from ruining my filament while it prints in my garage. The spool sits on the rollers inside the container and feeds out a tube on the bottom. The roller assembly has an...

The equipment tray and servo lock **must be printed as one assembly**. I separated them so you easily could make servo lock for different servo (in that case I use 1181MG servo). I made the square on the equipment tray floor for you to easy pairing...

Https://www.thingiverse.com/Apps/Customizer/run?thing_id=739573 Instructions: Using The Following Options: Text Outline Strategy For Non-Latin Scripts = bar and glyphs Outer Edge Color Of Design = gray Displayed Name On Model = kanu Frame Width Is...

I encourage experimentation with springs and perhaps with print settings if you know what you're doing to create a blaster fine-tuned to your needs. Grab your Snakethanhas here: https://www.thingiverse.com/thing:3890229 Feedback is very much...

You can set the X_MIN_POS to -1 and the Y_MIN_POS to -24 and the bed size to  234 on X and 211 on Y and then you won't run into issues with it trying to print off the edge of the build plate, you should also change them in the slicer to match. I...

I had problems with the walls printed vertically. As the plastic wires are laid one on top of the other, the wall is not very strong and it had the tendency with thermal shrinkage to crack. So I added different shaped ribs to see which ones are...

The support piece in the D-pad space will punch out with a punch and hammer after printing.Just place the shell on something with free space under the D-pad area and punch the support piece. Wiring the 9-pin d-sub for Amiga, Atari, Kempston or SEGA...

For example, I always made the print bed side visible because I liked the surface better there. With this little Stepdown Modules you can connect the 12V fans to the 24V power supply. If you have installed these two Noctua you only have to remove the...

I also added a box for the foreign market tiles for Lancashire.Brass Lancashire BOMItemQtyPurposebrass-lancashire-tile-box.stl4Industry tiles, link tiles, counters, Character tilebrass-lancashire-tile-lid.stl4 brass-lancashire-goods-box.stl1Iron...

Be sure to print the version appropriate for your application. In order to mount 12mm/14mm wheels to the adapters you first need to install <b>(1) M4x12 or longer socket head screw</b> through the center of the adapter (see pictures for...

blue lines or infill) should be ignored. Post-Printing Assembly Guide Tools needed:* ca 10 wooden toothpicks, 2mm diameter white glue. The one that dries in 5 minutes works best for me.</li> <li>adhesive tape to keep pieces in place, while the...

Two versions available: > 1.3.1 Wheel + 2.2 Distance: Can be printed without support and must then be glued together > 1.3.2 Wheel: All in all, but needs support (for Overhang Angle 89 °) The axles are small and the rims fit exactly, so make sure...

Added a photo showing the Endstop in fluorescent green filament. Print Settings Printer: Woodstock Delta Rafts: No Resolution: 0.2mm Infill: 25% Gyroid Filament: Generic PLA, PETG Any Notes: Orientation is often not correct, you will most likely...

----------------------------------- What you will need: * Four of the Corner Posts printed in your choice of plastic. * Two strips of polycarbonate strip 1/8" thick, 4" wide, 2 feet long. (Available from McMaster Carr in the USA part number...

Using it I created 12v powered Media centre with LibreElec running KODI so that I could watch TV-shows or movies in my RV without having to bring disks with me or have access to streaming services. I load the HD up with my ripped DVD's and then just...

Print instructionsPrinted with PLA plastic at 200 micron and around 7% fill. Mount the two front arms to the main body with a single zip tie. These zip ties should be quite snug, I used pliers. For the rear arm/pivot, first give the hinge slots a...

The two `o_ring` files are optional o-rings you could print with flex filament. Better to use o-rings, and at a pinch you can probably get away with using a rubber band, or just pushing everything together and putting up with water splashing...

K40 Paint Rack I recently started painting sla printed miniatures. Soon a lot of 25mm paint flasks crowded my workspace. So I was in need of some paint rack. I searched thingiverse but found none that appeals to me and whose parts will fit in my K40...

I print it with the cut in the bumper, which you can separate carefully with an exacto. Then wrap the bumper around, and trim the plugs as needed until it fits together well. Then I use my soldering iron (set around 3/medium) to heat up the edges...

The main point is that the duel disk can now be printed from a single spool, depending on your settings. Then I added some extra features for quality of life. Features: - All slots (monster, spell/trap, graveyard, extra deck) support cards in...

Plastic parts printed in PETG, layer 0.2mm, walls/top/bottom 1.2mm, infill 40%. With good part cooling supports are required only for the lower groove of the tool holders. Development log: 04/09/2023 Working sample 04/10/2029 "Head"...

This collection is a curated list for the Gridfinity system that includes Structural prints and common applications. The collection excludes any designs for unique tools or vanity items. ...Please like/favorite the original posts</p><p>If you are...

Alternatively, one could print the breasts and make an elastic mold. Step 1 If you look at the breast from the front and imagine a ball in the breast; what diameter would the ball be? <b>Bd= x (mm)</b> If you look at the doll's chest from...

First, you'll need a 2 gallon bucket (I got one from Home Depot for a few bucks), some M5 screws and some M5 knurled brass threaded inserts (use a soldering iron to install in plastic).I also included a strap mount so I didn't have to carry the ICM...

This is installed 30mm below the top of the vertical frame, or any distance you prefer The Z axis and bed are then moved so they are around 42-43mm below the X & Y axis Print one of each part, in the orientation you find them, no supports are...

electrical conduit pole. Print instructionsWhy I Built It I have an outdoor weather station that has batteries inside the instrument array. Changing the two lithium AA batteries once per year involves getting on the roof which is a PIA, so the idea...

Order of Operations !!!CAREFUL When you are done printing and are removing supports, make sure to be very careful on the Mainboard side. There is a 5th screw that is buried in the support material so just be careful that you don't rip it off. Won't...

Instructions If you plan to print in ABS, scale the object up by one press of the up arrow or the case will be too tight. ... Using the following options: 5width = 58.6 5height = 7.6 iphone_version = 1 4_per radius = .3 pattern_rotation = 10 5cornerR...