3d printed moss pole

Assembly video (in Russian): https://www.youtube.com/watch?v=rt2GikOnDV8 The parts are printed with PLA plastic, the body and struts are 100% infill, the wheel guard mounts are 75%, the wheels are 50%. When assembled, my copy weighs 1466 grams. ...

Although these files have not been extensively tested through printing, they are intended to be resized to match common modelling and miniatures scales. Target scale - Scale STL files to: - Notes 1/3900 - 0.25641026 - FASA miniature scale 1/3788 -...

This is installed 30mm below the top of the vertical frame, or any distance you prefer The Z axis and bed are then moved so they are around 42-43mm below the X & Y axis Print one of each part, in the orientation you find them, no supports are...

This is mainly composed by Nitrogen (98%) it is 1.45 times the pressure of that of Earth at the surface, and it is 1.19 times more massive. Titan atmosphere has a climate system, in which methane sublimate and form clouds. It is known that Titan has...

Tips Be sure your Z axis is positioned so that the endstop is above the level of the print bed before you begin the z probing procedure. You can also use the adjustment for raising the Z axis when probing to help. Finally, I welcome all feedback. It...

There is a through-hole for the display and button cable.I also had to print a stand that is screwed onto the load sensor to get a smaller contact area due to the slight angle of the adapter.Included is a schematic on how everything is connected as...

There are also two variants of each model - one "basic" variant, and one variant that has been slightly altered to suit printing at 28mm scale. You will find all 28mm variants in the zip archive named "28mm versions" included in the purchase. All...

It was not intended for printing purposes. I wanted to design some custom cases for CHIP and I always start by modeling the subject before moving on to designing accessories. However, until I had the actual CHIP board in my hands, I couldn't even...

You’ll need a large printer for the Converter to accommodate the handles but it was necessary to print in one for strength (peace of mind when a £500 drone hangs in the balance). The phone clamp requires an 80mm M6 threaded bolt (I buy threaded...

I printed the part using supports which are only necessary for the corners to the upright face. -- x -- I've also included a camera housing for the rear camera (plus fittings). It is intended that this will be attached to the upper plastic trim...

There are two methods you can use, either print up a new modified WhiskerScar with the rib cut out for a 19 mm OD and 16mm ID 1.7 mm thickness o ring (or some close equivalent) or you can use electrical or masking tape on an existing Whisker scar...

Plastic parts printed in PETG, layer 0.2mm, walls/top/bottom 1.2mm, infill 40%. With good part cooling supports are required only for the lower groove of the tool holders. Development log: 04/09/2023 Working sample 04/10/2029 "Head"...

I need my printer to be able to use stronger higher temp materials and be able to print delicate single perimeter components for the wings and fuselage. I decided a direct drive upgrade would be a good upgrade to provide better performance and higher...

3X M6 hex nuts - two for EAF adapter and one for TP-Link adapter If you use a William Optics Dual-Sided 210mm or 245mm dovetail plate, use the following bolts: 2X M6x60 SHCS for riser 2X M6x20 SHCS for EAF adapter 1X M4x16 SHCS for ASIair Pro 1X...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

I have NOT built or printed this option, but I am confident it will work fine. You can probably source some thin material to take up any slop in the assembly - even the sheet of foam that is provided in the original tinySA packaging box could work...

For example, I always made the print bed side visible because I liked the surface better there. With this little Stepdown Modules you can connect the 12V fans to the 24V power supply. If you have installed these two Noctua you only have to remove the...

Both had minor errors that possibly causes them to print badlyUpdate 20.11.2023:-32 and 35 is the same, but the file for 32 is flawed and therefore gets deleted.If you like my work please consider supporting me on Patreon.Become a Patron!Some of my...

By any means you are now scared to do this operation, I highly suggest you ask someone with expertise to help you on your endeavors.You have been warned.Step 1: partsFirst you need Noctua nf-f12 for the psu and Noctua NF-A4x10 FLX 12v Version.you...

It is represented the inner part of the cold region of the disk, which is about the diameter of Pluto. The "middle" cold disk goes almost as wide as Saturn. The disk is actually a lot less thicker than this, but it is was made like that in order to...

Assume structure can move only rightwards from starting points at given array perimeter += (future_value - current_value) + (shape[1+i] == '1') print(perimeter) ``` Note: `0`s or non-matching nodes could be part of structure, though no code will...

... soon. For those of you thinking about supporting us on Patreon, our patrons get special access to our entire back catalog, including the Meepleverse stuff (not to mention license options to sell printed versions of our designs). ... Happy holidays!

(I use 4 x 25mm M2 screws) For mountig my rx and vtx, i printed 1 x vtx_base.stl which fits onto the fc stack. For the rectangle standoffs you need 2 screws and 2 nuts to fix it. These standoffs are inteded to use at the left, right and rear side...

Order of Operations !!!CAREFUL When you are done printing and are removing supports, make sure to be very careful on the Mainboard side. There is a 5th screw that is buried in the support material so just be careful that you don't rip it off. Won't...

Print all the parts before assembling anything. 4. Start by assembling all the windows, doors, and trim as shown in image 1. 5. Assemble the motor mounts by gluing the two halves together. Ensure you align the holes before gluing. 6. Attach them...

NOTE3: If you decided to print all of these parts with some others you made yourself, don't come crying to me if nothing fits. This design is not complete and not tested at all. NOTE4: (This is for the future) This design is designed to work with...

This collection is a curated list for the Gridfinity system that includes Structural prints and common applications. The collection excludes any designs for unique tools or vanity items. ...Please like/favorite the original posts</p><p>If you are...

this should be intuitive ISSUE ADDRESSED 1 OF 3, The manufacturer claims a print area of 240mm x 290mm. (I don't think I was getting even that!), but more could be squeezed out with alternate parts The issue is with the wheels that are mounted to...

* Print out all parts with whatever material/color you would like. * (optional but helpful) Use a thread tap on all screw holes #### Start Assembly * Tap threads for push button. If you don't have a tap, you can use the push button to create the...

For him, the wheel rims are printed on a printer, and the tires are used from those wheels that are sold in the store. The chassis has slots for Arduino UNO, L298N motor driver, HC-06 Bluetooth module (HC-05 and others of the same size should do),...