3d printed monitor stand

Not really a remix, but strangely stumbled on [this other monitor stand](https://www.thingiverse.com/thing:4656621) that closely resembled what I had printed myself a couple of weeks ago. Decided to add it here as a remix since it is pretty similarly...

I needed a simple stand for my monitor with a curved back, so I came up with this simple design. I included two holes for screws with a shaft diameter of around 4,11 mm for those wanting to secure the stands to the ground below. For my personal setup...

Stand Monitor soliworksa 2023 instagram @topbiko_speedMass properties of Assem1 Stand laptop ( papan + rangka) Configuration: Default Coordinate system: -- default --Mass = 5.25 poundsVolume = 79.34 cubic inchesSurface area = 703.58 square...

I required a stand to hold my monitor upright instead of having to place something behind it, or on its original stand. I created this because I needed the stand to fit perfectly in the space under a compartment and my desk, and having it on its...

Monitor Stand/ Estante para monitor The part that is printed are the legs, the part of the base is melamine and it measures 1.5 cm, The dimensions are up to your own taste, but I recommend 10 cm in height, and make it the size that fits your keyboard...

Monitor stand legs. I used a generic shelf for the top. ...The legs have 3 screw holes on the base to fix it, depending on the weight you expect you can use 1, 2 or all of them. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter...

I ended up printing four of these custom stands and bonding them together using two-part epoxy. ...Finally, I added some surface grip pads - similar to those available on Amazon...

This is a monitor stand that I made to fit with a piece of wood that I had laying around. It's designed for 11 and 3/8ths of an inch wide wood and 5/8ths of an inch thick. ...(Length doesn't matter) Category: Office

Something I whipped up in fifteen minutes in Fusion 360 because I needed a couple of monitor stands at my work. The four bottom pieces mate into the slab, and the legs thread into the bottom pieces. Simple. No BS. Not fancy. ...Functional.

This is a monitor stand that I made to fit with a piece of wood that I had laying around. It's designed for 11 and 3/8ths of an inch wide wood and 5/8ths of an inch thick. ...(Length doesn't matter) Category: Office

This is a monitor stand that I made to fit with a piece of wood that I had laying around. It's designed for 11 and 3/8ths of an inch wide wood and 5/8ths of an inch thick. ...(Length doesn't matter)

So designed and printed the Monitor mount. Used 5/16" nuts and bolts to hold it on. It is not designed to take a lot of abuse Works quite well. Standard VESA standard FDMI MIS-D for mounting holes (75mm x 75mm) on the monitor and 25mm thick...

... reach your desired lenght. The 13mm aluminimum tubes can be bought at the construction markets for a few Euros. Print with PLA and 100% infill to provide strength. Glue the tubes and the joints together. ...No support needed when printing.

These are the feet of a monitor stand i created. You'll need a wooden plank to complete the stand. The lenght and the width is up to you. You only need to drill holes in it to fix it. ...You can also just glue it, it should hold.As it will probably hold...

Remix for the 3D Printed VESA Monitor Arm to fit 100x100 Monitors

I designed this for a 27" Samsung curved monitor, as the stand it came with made it sit much too low on my desk. It should work for any other monitor with a base that's smaller than 20x20cm, and will lift it up by 12.5cm. You will need two equal...

... across, adding a touch of functionality to its design. This versatile base not only elevates small televisions but also holds a remarkable weight of at least 100 pounds, as demonstrated by the challenge of standing on it successfully during testing.

This is a straightforward printer stand that requires minimal effort. ...Simply print the stand's legs twice, then secure them beneath a wooden base of your preference using screws.

You can build a monitor stand using standard 3/4" boards or plywood as the horizontal surface. It features two mirrored corners and one symmetrical leg that serves as a middle support, offering extra stability when needed. The legs are designed for...

You can install a central leg to hold up the monitor base if it extends far beyond the desk edge.

Legs for a monitor stand (or any kind of short table) that utilize a standard 3/4" boards or plywood as the horizontal surface. There are two mirrored corners and one symmetrical leg which can be used in the middle if you need some extra support or...

User interface: refers to the simplified appearance of a Computer screen displayed on a Monitor device from the User's perspective.

This sleek 20-cm tall monitor riser elevates your screen to an ideal viewing height, perfecting posture and reducing strain on your back.

A small block use to hold portable monitor like Asus Zen Screen. I've build it on a Creality Ender 3 V3 SE at .12mm resolution

Compact desktop holders provide ample space for monitors measuring up to 1.25 inches thick, keeping them securely at eye level.

I crafted this to place my keyboard directly underneath my monitor, thereby decluttering my workspace. I can modify the .SLDRT file using SolidWorks. ...The .DWG file is specifically requested for laser cutting and bending purposes.

No Hardware needed.Just put the raisrer Feet under the Monitor.The Front Feet are the same for all versions.There is space for rupper feet.3 Versions:Simple no Docking stationShort for docking stationLong for Docking station

... as the focal point. ...The printer-friendly creation requires M5 and M6 bolts for assembly. Crafted using 25mm square piping, it is compatible with makedaves monitor mount (excluding the wall piece) available at http://www.thingiverse.com/thing:22934.

I'm taking a trip down memory lane to my old gaming days, when I had three monitors set up and running simultaneously. The bezels on those screens were always getting on my nerves, so I took matters into my own hands and ripped them off. ...Little did I...

Podstavec pod monitor je tvořen dvěma vytisknutými díly (nohy) a jedním dřevěným prknem, pod které je možné schovat klávesnici a mít tak uklizený stůl. Parametry / parameters:tloušťka prkna / board thickness: 20 mmdélka prkna / board length:...