3d printed monitor stand

This stand for headphones is created from multiple printed components and can be fully customized to suit individual preferences. Additional parts can be easily printed to increase the height, allowing users to tailor the design to their needs. I...

Here is the rewritten text: Modular dual monitor stand built around sturdy metallic tubes with an outer diameter of 25mm, featuring a versatile VESA 75/100 mount. Recommended tube lengths include two vertical segments measuring 500mm each and two...

A rubber tape of some sort can be applied to areas where it touches the monitor for improved grip and to prevent scratching the surface. I personally used thin weather stripping foam from Aliexpress. ... I may improve it eventually when time allows,...

The support.stl file must be printed twice for the FPV monitor to work properly on your drone remote control. For fixing use flat head screws and nuts with 3mm holes that perfectly fit into place. ...For more details visit...

The system was created specifically for Vivo brand desktop monitor stands with a center column diameter of approximately 36mm. A comprehensive schematic and STL files for decorative embellishments are included; these can be omitted if desired. If...

It's 3D printed part that allows the robot to be left up to tests can run.

 HS8 will fit fine as well but you can alter dimensions for other monitors.I printed in PLA + but any filament will work. Infill 10+,  with a brim to minimize edge/corner warping.Printed on a Tronxy X5SA Pro 330 and they are 252mm long. ...Printed with...

Using a Vesa mount on the back of your monitor(or tv) you can screw this print and you are ready to go! Print instructionsThis model requires no support and you simply just print and use 2 m4 * 12mm screws to attach to monitor DISCLAIMER: There is an...

A custom-made stand holds four monitors with dimensions of 3 x 23.6 inches and 1 x 21.5 inches, crafted from 3/4 inch tubes. The PC uses a MicroATX computer case (https://grabcad.com/library/aime-c600-microatx-computer-case-1) and is equipped with a...

Here's another monitor stand with a VESA 75x75 mount, featuring a knock-off nut for adjusting the angle of your display. The necessary screws include: Four M4x8 screws for securing the VESA mount One M5x30 bolt for added stability One M5 nut for...

There are two types of individuals: those who possess a portable second monitor for their laptop and those who have yet to realize the need for one. The Asus MB169B+ comes with a protective case designed to serve as a stand, but its performance is...

Small TV/Monitor Stand Recommendation to check the final measurements for the use to be given on the page "Tinkercad", which was the page where it was designed and modified, as it is a support remember to increase the padding for greater hardness.

Raise the monitor and free up desk space

Monitor Mount Clip Headphones Holder Attaches to Computer Screen

*** Print the Monitor mount 'laying on its side' so that worm teeth are parallel and half way up the print. *** Use supports on everything except the Crank Knob. *** Print the Base with 50% infill or more for structural strength. *** Some...

... complaining that her monitor was too low so I remixed these models together in tinkercad. ...Sorry the prints didn't turn out great the prints failed at one point and I had to reprint the bottom halves of the leg and tail and then glued them together.

... was too low so I remixed these models together in tinkercad. ...Sorry the prints didn't turn out great the prints failed at one point and I had to reprint the bottom halves of the leg and tail and then glued them together. ... Category: Computer

... was too low so I remixed these models together in tinkercad. ...Sorry the prints didn't turn out great the prints failed at one point and I had to reprint the bottom halves of the leg and tail and then glued them together. ... Category: Computer

Hi, "thingy people" I needed a bit more space under my 'monitor stand', there is plenty of room for my Mac-Mini but that is all that will fit... So I produced a simple design for my specific stand (as shown in the images) and raise it another 50mm...

These are legs I created to use with a piece of wood to create a stand for your monitor. You will need 3/4 wood at 8 inches deep to friction fit into the slot. The length is up to you I suggest if you use it longer use more legs to counter any...

LED display bases: https://www.amazon.com/Display-LETS-RESIN-Lighted-Crystal/dp/B07T6ZS2XZ/ref=pd_rhf_se_p_img_1?_encoding=UTF8&psc=1&refRID=7M6CMJBEFHVHKGWBFZ7P These stands was designed for lithographs printed using the website below using the...

May Not Function Properly with Other Models Due to Distinct Dimensional Characteristics.** I encountered a challenge that prevented my KRK monitors from being angled correctly towards me. The solution was this compact stand. **Key Features** *...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/hTvslAw5bRt This was made for a 4.3" Furrion Monitor I printed it on my Voxelab Aquila. ... Just needs a 4mm X 1" bolt and lock nut.

I made this stand because I detested the other stands available, which either demanded additional hardware or were impossible to remove and made me fear damaging my Volcas. There were some tweaks that could be made but I never implemented them...

3D Printed Mini Portable Laptop StandHere You can see a full video of making: https://yashthummar.wixsite.com/portfolio/3d-printed-portable-laptop-standThese are fixed directly on the bottom of your laptop and give some space for air circulation to...

You can technically configure these parts to make a huge array of monitors, and you can use the spare space on the leg to attach other devices (like webcams, lights, speakers etc.). As always with my designs - use them at your own risk. ...I'm not...

I purchased a budget-friendly Chinese 10-inch full HD monitor that arrived without a base or stand, so I designed one to meet my needs. Two types of rear plates were also created, both equipped with standard VESA mount holes spaced at 75 and 100 mm.

This tray is specifically designed to snap onto a 48mm monitor stand base. A channel for securing with a zip tie is provided, just in case the fit isn't snug enough - fortunately, it hasn't been an issue so far. To make this tray work with PETG...

... the satechi holder in place. The satechi holder is this one: https://www.amazon.com/Satechi-Aluminum-Multi-Angle-Foldable-Tablet/dp/B004X2TJ1W/ref=sr_1_2_sspa?keywords=satechi+stand&qid=1688303707&sr=8-2-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9hdGY&psc=1

(EN): I made this support to be able to raise the height of my monitors, I had a piece of wood made in the measurements: 1000 x 240 x 15mm, and I printed the legs of this support and screwed them to the wood and the table to guarantee the fixation.It...