3d printed medals

The support piece in the D-pad space will punch out with a punch and hammer after printing.Just place the shell on something with free space under the D-pad area and punch the support piece. Wiring the 9-pin d-sub for Amiga, Atari, Kempston or SEGA...

# OpenSCAD Fully parametric drawer cable storage management hive with punch cuts (openscad-hex-cable-hive-fully-parametric)OpenSCAD Fully parametric drawer cable storage management hex hive with punch cutsThis is an OpenSCAD sketch to generate fully...

It should be fully rules complaint but check dimensions before using this design.Note: At time of upload, the design has not been tested in competition and has no guarantee of performance.Note: The pictures included with this design show a Launcher...

(I use 4 x 25mm M2 screws) For mountig my rx and vtx, i printed 1 x vtx_base.stl which fits onto the fc stack. For the rectangle standoffs you need 2 screws and 2 nuts to fix it. These standoffs are inteded to use at the left, right and rear side...

* Print out all parts with whatever material/color you would like. * (optional but helpful) Use a thread tap on all screw holes #### Start Assembly * Tap threads for push button. If you don't have a tap, you can use the push button to create the...

Let's collectively push the envelope of what's possible with Raspberry Pi.Download, print, and commence your journey with Poisonberry Pi - where the capabilities of your Raspberry Pi 5 are just the beginning.Exciting Update for Enhanced...

To achieve the insert as shown, print six of the player trays, two of the resource/silver trays, and one of everything else. The photos show how to layer all the trays, game board, and manuals in the box. ... I have included the original OpenSCAD...

Screw or push inserts would probably also work after drilling the holes to the required size for these inserts (no guarentee) - 5x M3x5mm allen head set screw ###Printed parts - 1x Base - 1x Stepper_Housing **(requires support)** - 2x Front_Wheel -...

Tips Be sure your Z axis is positioned so that the endstop is above the level of the print bed before you begin the z probing procedure. You can also use the adjustment for raising the Z axis when probing to help. Finally, I welcome all feedback. It...

If your looking for the original look the v1.0 release at my Github repository: https://github.com/kellyegan/Arduino-Mounting-OpenSCAD-Library The library uses tbuser's pin library for the pin mounts: http://www.thingiverse.com/thing:10541 There are...

Once the bed has been measured, dropping the nozzle to print height will bring the nail back in range of the magnet and retract it to the stowed position. The M5 iron grub screw attracts the magnet back to center and also helps extend and...

==================================================================== Easy to print, assemble, mount/unmount. To assemble with Nema14 motor you will need: ----------------------------------- * A set of parts from BMG or clone (gears, bearings,...

Shoulders and Forearms(https://www.aguilarworkshop.com/product-page/odst-battle-armor-arms)Armored Plate Carrier(https://www.aguilarworkshop.com/product-page/odst-battle-armor-armored-plate-carrier)Utility...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

I provide an easy-to-print alignment tool to ensure the heatsink is perfectly positioned for the cover to fit.\n* Direct airflow through the heatsink, don't leave proper airflow to chance.\n* Duct air in one side and out the opposite to maximize the...

This is my over complicated / over engineered solution to prevent humidity from ruining my filament while it prints in my garage. The spool sits on the rollers inside the container and feeds out a tube on the bottom. The roller assembly has an...

- The diameters of the holes is optimized to be just right to get 0.5mm holes, tight, using a 0.4mm nozzle and printing at normal cura settings at 190C of temperature. Beware higher temperatures, the walls sag and clog the hole. You should modify...

The templates cut the rods a little short (3mm) so that there is room for any tolerance stackup in the X and Y axes.Some NotesAll of the parts (except for 1) are printable without supports I recommend 100% infill for the “Sand Cover” piece to...

Shoulders and Forearms (https://www.aguilarworkshop.com/product-page/odst-battle-armor-arms) Armored Plate Carrier (https://www.aguilarworkshop.com/product-page/odst-battle-armor-armored-plate-carrier) Utility Belt/Waist...

... after days, or use a step-by-step motor or a properly controlled servo motor. I took advantage of the suggestion in the comments to widen the dial, so you can read the time well between 9 and 12, the result seems very good to me. Happy printing!

Note: Someone has mentioned the possibility of additional electromagnetic interference generated by the psu by removing the metal lid, so I may try to print this later in conductive filament. As of now, I have yet to experience any downsides of using...

On my desk was a sample of TPU filament (I had never got around to printing with it) and playing with the filament I thought: "if I can attach this to the model"... After repeated attempts to come up with a clamping system, I soon found out that the...

... It was only off .13mm (.0051 inches) at the most, but not really an issue if you have printed the parts already. Here is very short video of this machine working. https://youtu.be/HgV3grxkY44 I also added optional **CantileverStablizer.stl**.

In a few million of years Eros could change its orbit to a lower Earth crossing one, becoming a member of the Apollo or Aten group. Depending on how close it became to the Earth, it could be a Potentially Hazardous object (PHO), an object capable of...

To achieve a smoother rail on my new mk3 set, I've attempted to join the parts together at a diagonal, although this is still theoretical since I haven't printed the assembly yet. My symbol ring keeps getting stuck, possibly due to using the wrong...

[7] Thing Title : Tweezers (single print) Type 1 Simonwlchan created a set of precision tweezers, made available under Creative Commons - Attribution on thingiverse.com. [7] Thing URL : http://www.thingiverse.com/thing:1081911 Find the detailed...

The major innovation in coins the Byzantine’s made was to have the emperor face the front rather than print a profile. Most US coins would then adapt the side profile and bank notes adapt a front facing image, if not cocked to the side just slightly....

It will then print out a message to the console with the planet's name, its description, and its scale. Please note that this is just an example script, and you may need to modify it to fit your specific needs. Additionally, this script assumes that...

Happy printing and happy gaming! And of course there's lore to go with this; it wouldn't be me without it: The Landshark Grav Tank is another product of the labors of Belisarius Cawl and his faction within the Adeptus Mechanicus. Intended to fill...

Little material and time is required for printing. The "screws" and "nuts" can be pushed onto one another with a little force, the components are too small for a screw connection. I use the fan on the desk and another one to circulate air in a mold...